Brick Masonry, Plaster Work, Tile Flooring and Internal Sanitary / Water Supply etc. In Lecture Hall Cum Laboratory Block at Govt. Medical College Works Anantnag.

Amount

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more including cost of meterial & all other charges / complete job.

Providing and laying in position machine mixed design mix M25 grade of reinforced cement concrete excluding the cost of centering ,shuttering, finishing and reinforcement. above plinth level.upto all levels (cement content @330 Kgs/cum including cost of meterial & all other charges / complete job.

Extra for providing richer mixes at all floor levels. Providing M30 grade concrete instead of M25 grade . Cement Content considered @340kgs / cum including cost of meterial & all other charges / complete job.

Add for using more cement in the design mix over and above the specified cement content there in, (450kgs instead of 340kgs) to be paid as per actual design Mix including cost of meterial & all other charges / complete job.

Centering and shuttering including strutting, propping etc. and removal of form for:

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, piers, abutments, posts and struts.

Suspended floors, roofs, landings, balconies and access platforms.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor five level

Extra for brick work in superstructure above plinth above floor five level

15mm cement plaster on the walls of single or half brick wall of mix 1: 6 ( 1 cement : 6 coarse sand) . (interior) including cost of meterial & all other charges / complete job.

20mm cement plaster on the walls of single or half brick wall of mix 1: 6 ( 1 cement : 6 coarse sand). (exterior) including cost of meterial & all other charges / complete job.

6mm cement plaster to ceiling of mix (1:3) 1 Cement : 3 Fine sand) including cost of meterial & all other charges / complete job.

Extra for plastering exterior walls of hight more than 10mts of hight from ground level Upto all hights including cost of meterial & all other charges / complete job.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:4:8 (1 Cement: 4 coarse Sand: 8 Graded Stone aggregates crushed 40 mm nominal size) including cost of meterial & all other charges / complete job.

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 above plinth including curing in : Cement mortar 1:3 ( 1 cement : 3 coarse sand) including cost of meterial & all other charges / complete job.

Rebaring in RCC Work including marking position,making and cleaning of holes supply and application of rebaring chemical of approved Quality (HIT HY 200 of HILTY make ) including cost of meterial & all other charges / complete job.

Supply and fixing of Deodar wood frames of Doors, windows clestory windows and other frames , wrought framed and fixed in position with dash fastners of required dia and length (cost of dash fastners shall be paid separately ). Size and section a per Architectural drawings

Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing 40x5 mm flat iron hold fast 40 em long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and em beddings in cement concrete block 30x10 x15 em 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size )

Providing and laying Industrial floor tiles of size as mentioned below (15 mm thickness as specified by the manufacturer) with water absorption less than 0.5% and conforming to IS-4457:2007, flexural strength not less than 38N/sqmm & Breaking strength not less than 4000N, of approved make, in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand), including grouting & jointing with Laticrete or approved equivalent jointing compound of matching shade in place of white cement with matching pigment all complete as per direction complete. Size of Tile: 300 mm x 300 mm x 15 mm thick including cost of meterial & all other charges / complete job.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Eningeerin- Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarse sand) and jointing wtih grey cement slurry@ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.(digital) including cost of meterial & all other charges / complete job.

Providing and laying Double charged vitrified floor tiles size 600x600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make (Kajaria, Somany or equivalent) in all colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand), on floor and skirting/dado in patterns as per Archetctural drawings/directions of Engineer-in-charge of the site including grouting the joints with white cement and matching pigment including cost of meterial & all other charges / complete job.

Providing an applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Cement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 50mm thick with 20mm nominal size of stone aggregates including cost of meterial & all other charges / complete job.

Providing and laying Polished Granite stone flooring and skirting/dado 100mm-150mm in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed withpigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge including cost of meterial & all other charges / complete job.

Providing and laying Anti-skid Ceramic Floor Tiles (300x300) of Standard Quality and approved make (digital Matt) in all colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand), on floor and skirting/dado in patterns as per Archetctural drawings/directions of Engineer-in-charge of the site including grouting the joints with white cement and matching pigments including cost of meterial & all other charges / complete job.

Providing and fixing 16 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite Slab for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.(jet black )

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White vitreous china Orissa pattern WC pan of size 580 x 440mm with intergal type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing white vitreous china wash basin oval Type (counter Top) 56X41cm 32 mm C.P. brass waste of standard pattern,including cutting and making good the walls wherever require :

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder. C.P. Brass

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore

Providing, fixing, testing and commissioning of CP brass central hole wash basin mixer (table mounted) without popup waste with brass nuts casted spout complete including cutting and making good wherever required.

Providing & fixing grab bar (SS 304) in toilets for physically handicapped with non-slip gripping surface complete in all respects, including cutting and making good the wall wherever required.

Providing & fixing 600 mm grab rail (SS 304) in toilets for physically handicapped with non-slip gripping surface complete in all respects, including cutting and making good the wall wherever required.

Supply, fixing, testing and commissioning of storage type automatic electric hot water heater made out of heavy gauge steel jacket finished with rust proof baked-on glossy white enamel paint, inside glass lined heavy gauge steel tank, 25 mm thick polyurethane foam insulation, thermostatically controlled immersion heater with pilot neon lamp, replaceable magnesium anode bar, suitable for 8.0 bar maximum working pressure, cold water inlet and hot water outlet pipe, suitable length of electrical cable and 15 amp 3 pin plug top, non return valve and pressure release valve complete in all respect including testing etc. (Horizontal/Vertical)

15 litres storage capacity

25 litres storage capacity

soil, waste and vent pipes: Providing and fixing 3 layer PP-R(Poly propylene Random copolymer) pipes of standard quality having minimum SDR value 11 UV stablized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitings I/C trenching, refilling and testing of joints complete as per direction of Engineer-incharge.(Make :- Astral, Finolex, Supreme)

PN-10 pipe , 110mm OD (SDR-11)

Providing and fixing PP Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections.110 mm inlet & 110 mm outlet

Providing and fixing 125 mm dia, 1 mm thick stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.

Providing and fixing floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for waste, with SS grating (adjustable height), having 50mm water seal.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes of standard make SOR 7.4 UV stablized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitings 1/C fixing the pipe with clamps at 1.00m spacing. (For Indirect waste/ Wash Basin/Urinal/Sink/Floor Drain (Make :- Astral, Finolex, Supreme)as per direction of Engineer-in-charge

Pn-16 pipe , 40mm OD

Pn-16 pipe , 50mm OD

Pn-16 pipe , 63 mm OD

Providing, fixing, testing and commissioning of pipe inlet fittings fabricated with maximum 3 inlets 40, 50 & 75 mm OD size fixed to 'P' traps including Dripseal/Pipe seal/solvent weld joint/rubber ring joint complete .

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. (Make :- Astral, Finolex, Supreme) Concealed work,including cutting chases and making good the wall etc.

PN-16 pipe , 20mm OD

PN-16 pipe , 25mm OD

PN-16 pipe , 32 mm OD

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. (Make :- Astral, Finolex, Supreme) Internal Exposed on walls

PN-16 pipe , 32 mm OD

PN-16 pipe , 40 mm OD

PN-10 pipe , 50 mm OD

PN-10 pipe , 63 mm OD

PN-10 pipe , 75 mm OD

PN-10 pipe , 90 mm OD

Providing and fixing brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 and spindle AISI 410) with setting and gland of superior quality having minimum working pressure of 10 kg/cm2.

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

90 mm nominal bore

Providing and fixing, testing and commissioning CI double flanges suction strainer (PN 1.6) “Y” type including, nuts, bolts and 3mm thick rubber insertion complete. Installed at terrace for water supply and fire line downtake pipes.

80 mm dia

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc. And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil. All kind of soil Pipes, cables etc, exceeding 80mm dia but not exceeding 300 mm dia.

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete including cost of meterial & all other charges / complete job.

100 mm diameter

150 mm diameter

Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround stoneware/RCC pipes including in bed for pipes to be laid in trenches as per standard details including cost of meterial & all other charges / complete job.

100 mm diameter

150 mm diameter

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

150 x 100 mm size P type FPS bricks

Constructing brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C. top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 cm and 45 cm deep including CI Cover with frame (light duty ) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15 kg) FPS bricks including cost of meterial & all other charges / complete job.

Extra for depth for manholes Size 90 x 80 cm FPS bricks

Providing nallah boulder , including placing hand packed in under floors & carriages etc. complete.

Making of concrete plate form for orissa patern WC 900X1200,in size and 150mm height.(1:3:6)

P/L cinder filling in sunk slab including compacting mannually with rammer and finishing true line and level at all floor level etc. complete as directed by Engineer in charge

Providing and laying water proofing treatment in sunken portion of Gutters, WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying: (Tapecrete of CICO or approved equivalent). 1st layer of slurry of cement @ 0.488kg/ Sqm. mixed with water proofing cement compound @ 0.253kg/ Sqm. This layer will be allowed to air cure for 4hours. 2nd layer of slurry of cement @ 0.242kg/ Sqm. mixed with water proofing cement compound @ 0.126kg/ Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering ,shuttering, finishing and reinforcement. above plinth level. 1:2:4 (1cement : 2 coarsesand: 4 crushed Stone aggregates 20 mm nominal size ) including cost of meterial & all other charges / complete job.

Providing and fixing PVC four layer water storage tank of Sintex make including installation, making inlet and out let connection complete

Providing and fixing tanky nipples G I of standard quality and make ( 90mm nominal bore)

Providing and fixing white vitreous china flat back half stall urinal basin of 580x380x350mm with Flat White P.V.C automatic flushing cistern, of approved make with fittings, C.I./M.S. brackets, standard size of C.P. brass flush pipe, spreaders with unions and clamps complete, (all in C.P. brass) with waste fitting as per IS:2556, C.l trap with outlet grating and other couplings in C.P brass including painting of fittings and brackets, cutting and making good the walls and floors wherever required: Single half stall urinal with 5 litre white P.V.C automatic flushing cistern of approved

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite stone of approved shade including cost of meterial & all other charges / complete job.

SUBZAR AHMED ROY