Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Finance | Admitted-Finance |
| 2 | Admitted-Finance INDEX NO B 33 NC R O KRALPORA DISTT BUDGAM SRINAGAR J K 190019 | SRINAGAR | BUDGAM | JAMMU AND KASHMIR | 190019 | Admitted-Finance |
| 3 | Admitted-Finance | Admitted-Finance |
| 4 | Admitted-Finance | Admitted-Finance |
| 5 | Admitted-Finance | Admitted-Finance |
Tender Value
₹23 L
EMD Value
₹46,000
Closing Date
19 Jun 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GARRISON ENGINEER
GE 970 EWS C/O 56 APO PIN 913970
PROVN OF DG SET AND HIGH MAST LIGHT AT JAK LI RC UNDER GE 970 EWS
2023_MES_596959_1
GE 970 EWS-09/2023-24
Open Tender
Electrical and Maintenance Works
Item Rate
180 days
GE 970 EWS C/O 56 APO
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
GE 970 EWS
₹46,000
Yes
11 Jul 2023
20 May 2023
21 Jun 2023
20 May 2023
19 Jun 2023
4 Jun 2023
Amount
Supply, installation, testing and commissioning of silent type diesel engine driven generating set with governing class G2 including sound reducing canopy (sound level not more than 75 decibal from 1 mtr distance) 14 gauge as per guideline issued by central pollution control board, 415 volts, 3 phase, 50 Hz supply suitable for giving an output of 125 KVA after considering derating factor confirming to IS-1601 at 5430 feet (approx) altitude above mean sea level and capable of operating between temperature range (-) 20 degree centigrade to (+) 40 degree centigrade (at Srinagar, J&K) and alternator of suitable capacity and RPM coupled with each other with flexible coupling mounted on common base plate on anti vibration pads on foundation as recommended by manufacturer. (a) Alternator: Directly coupled with engine and suitable to produce 415 volts, 3 phase 4 wire system, 50 Hz, 0.8 power factor @ 1500 RPM of capacity 125 KVA all as per IS-13364 and upto date amendments with H class insulation self excited, self regulated, screen protected drip proof type with two end shield ball/roller bearing with damper winding in each pole all as specified and directed. (b) Engine : Water cooled diesel engine (CPCB norms compliance) as recommended by the manufacturer for 5430 feet altitude having self start engine (including batteries with provision of charging the batteries and leads) suitable to drive above specified alternator complete with foundation (foundation design as per OEM), as per IS-10001/10002, coupled directly through flexible coupling, multi cylinder four stroke, cold starting, 1500 RPM industrial type with AI electronic governor suitable to regulate speed of DG set from No load to full load complete with fuel tank of capacity as per manufacturer recommendations, fuel lines, exhaust pipe duly insulated with asbestos rope and with support and silencer mufflers etc for continuous operation and standard accessories, sump pre heaters, cold start kit etc all as specified and directed. (c) Canopy : Canopy enclosure shall be powder coated and fabricated out of power coated after passing through seven tank process 16 SWG CRCA MS sheet and lockable doors should be provided in canopy with lockable fuel filling arrangement provided external to the canopy. The exhaust system and noise suppressor shall be provided with thermal insulation by using fire retardant/non igniting foam to prevent excess heat radiation on the engine and safe for operator. Absorption type non resistance residential silencer shall be provided to suppress exhaust noise from the engine. (d) Alignment and fuel tank : Alternator and engine aligned on a common 14 SWG CRCA MS base frame complete with MS fuel tank, fabricated out of 16 SWG CRCA MS sheet and is part of base frame. (e) Maintenance spares :- (i) Fuel filter element - 02 Nos (ii) Oil filter element - 03 Nos (iii) Element air cleaner outer - 06 Nos (iv) Element air cleaner inner - 06 Nos (v) 'V' belt - 02 Nos (vi) Filter lubricant oil bypass - 02 Nos (f) DG set shall be supplied along with acoustic enclosure of the manufacturer suitable for 125 KVA DG set as per CPCB norms.
Supply, installation, testing and commissioning of three Phase 415 V AMF Panel For 125 Kva DG set with power-200 Amps, current rating upto 200 Amps, aluminium bus bar, IP protection-65, changeove time of 0.5 sec, 3 Phase ATS with auto Start & Stop With Auto operation for Three Phase DG & Three Phase Mains (Double Interlocking) 4 pole 200 A. Contactors – 2 , for DG & Mains Control MCB, Timer, Volt Monitor Relay, Battery Charger 12V ,Panel Size: 700x1200x350 mm , Operating Voltage Range 130-280 VAC and all as specified and directed by Engr-in-Charge.
Supply and lay XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 95 sq mm 4 Core complete all as specified and directed. Note :- Suitable cable glands shall deemed to be include in this unit rate.
Supply and Fix Off Load change over switch 250 Amps, 4 Pole made out of Sheet metal enclosure and fixing arrangement on panel/wall complete all as specified and directed.
Material & labour for LT heat shrinkable cable jointing kit suitable for 4 core 95 Sqmm aluminium cable complete all as specified and directed.
Excavating in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation for laying cables, stays etc and getting out in hard / dense soil all as specified and directed.
Returning filling in, including spreading, levelling, watering and well ramming of excavated earth in layers n.exc 25cm thick in any type of soil complete all as specified and directed.
Removing excavated soil to a distance n.exc 50m, depositing where directed at a level n.exc 1.5M above the starting point complete all as specified and directed.
Supply and laying dry river sand in trenches for cable protection complete all as directed. Note : Punned thickness only will be measured & Paid.
M&L for Earthing complete with GI earth plate 60x60cmx6mm thick electrode and 32x6mm GI strip as earthing lead burried directly in ground (Earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metre below normal ground level, conneceted to GI strip 32x6mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 and incl earth work, PCC pit and RCC cover, watering pipe 20mm dia light grade, funnel, wire mesh, charcoal dust, 40mm dia light grade protection pipe and salt etc and connected to earthing test point all as specified or directed and testing complete all as specified.
M & L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, mass concrete etc complete all as specified and directed.
M&L for covered shed with CGI roof top on 02 Nos of MS angle trusses (65mmx65mmx6mm) of size 3.5 mtr x 2.5mtr over the PCC (1:3:6 type B2) foundation 2.5m x 2m x 0.6m, plinth protection (0.5 mtr wide) all around the shed and finishing the surface even and smooth and erecting 4 Nos of 80 mm dia heavy duty tubular pipes having height 3 mtr including well grouted in foundation 0.45x0.45x0.6 m, with 6 nos of purlins and 04 nos of angle iron to hold the tubular pipes and CGI fencing of size 13m x 3m including provn of gate of size 1.6x2.5 mtr with locking arrangements and painted with two coats synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.
M & L for HIGH MAST LIGHTING system with its accessories control panel housing etc, Nominal height of Mast 20 Mtrs, length of individual section : 10 Mtrs Base section and 10 Mtrs Top section, Base Dia : 350 mm and Top Dia : 150 mm, thickness of each section 3 mm, Cross section of Mast 12 sided Polygon, Size of Base flange : Diameter 540 mm and thickness 25 mm, Details of Template : P.C.D - 440 mm, not less than 06 Nos of foundation bolts, Material of Construction BSEN 10025, diameter of carriage ring inc. Arms 2100 mm(Approx), load carrying capacity 350 Kg (Approx), for 08 Number of luminaries, Double drum winch capacity 550 Kgs, Method of operation : Manual/Electrical, Stainless steel wire rope 2 Nos for winch and 3 for Lantern Carriage of size 6 mm diameter construction 7/19 with central core SS, Power tool input supply 440V, 50Hz, 0.75KW, Reversible,Power control copper cable 4 core as per suitable size, Torque Limiter mechanically Complete including necessary RCC foundation casting, earth work as per soil bearing capacity and manufacturer design and erection as required in 90° vertical including Power control housing suitable for Surya Make High mast Light fittings, it shall consist of suitable control for the power tool motor 440V, 50Hz, 0.75 KW, reversible, with timer,contractor facility complete as per OEM specifications and all as specified and as directed. Make : Surya Roshni Ltd/Bajaj / Crompton Greaves/hAVELLS
Supply and fixing of LED Floodlight luminaire 240 watts capacity with secondary optics made in pressure die cast housing and heat sik in aluminium extrusion and IP66 Protection fixed in the AOL bracket of High mast light fittings all as specified and as directed. (Make : Bajaj/Philips / CG/LEGERO)
Supply and fixing of Integral LED aviation light comprising of aluminium housing with polycarbonate enclosure fixed on the top of the High mast light fitting all as specified and as directed. (Make : Bajaj Cat No BGAV 302 LED or equivalent in Philips / CG).
Supply, installation, commisioning and testing of LT Control Junction board made up of 3 mm thick CRCA Sheet, double door, outdoor type, mounted on rigid angle iron frame, over all size not less than 600 x 600 x 450 mm, having independent compartment for bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of 3 mm thick CRCA sheet suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with copper bus bar of 100 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, common earth bus bar of GI Strip 32 x 6 mm at bottom with panel board at two earth terminals , cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour all as approved with and including following items: -
Incoming & Out going :-
a) MCCB 4 Pole, current rating 32 Amp, fixed thermal magnetic release, breaking capacity 16 kA at 415V, 50Hz, - 01 No.
b) Angle iron base frame as reqd size as per above panel, total leg height 600 mm and grouting in side PCC 150 mm legs and made out of ISA5050, 50 x 50 x 6 mm thick angle iron duly painted - 01 No.
c) M & L for necessary excavation and as reqd PCC 1:3:6 (40 mm graded aggregate) Type C2 for foundation of angle iron legs frame work complete - 01 job
Supply and lay LT Cable XLPE insulated heavy duty armoured sheathed 1100 volts grade 16 Sq mm, 4 core, with aluminium conductor, ISI marked as per IS : 7098( Part-1) complete all as specified.
Supply and fix GI Pipe light grade 40 mm bore for cable protection as a guard pipe including required accessories etc. complete as specified and directed.
Excavation in trenches n exc 1.5 Mtr wide and exc 1.5 Mtr deep but n exc 3 metre in soft/disintegrated rock and getting out and levelling of bottom surface to required level complete all as specified and directed by Engr- in- charge.
BLANK
Supplying & Laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250mm x 150mm x 40mm in trenches for protect to under ground cable complete all as specified.
M/S NEW ROYAL CONSTRUCTION CO
M/S M.Y Enterprises
CHINAR CONSTRUCTION TRADERS
M/S MIR SAJAD ENTERPRISES
M/S Noor Mohammad Shalla
G N Constructions
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .