Special Civil maintenance and repairs to staff quarters complex and renovation of NA-II quarters to IQ-II at Kanyakumari Lighthouse.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in?charge.

Plain cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) standard specifications and as directed by the Departmental officers.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) including mixing, placing, consolidation, curing etc., including cost of supply of all labours., materials, tools and plants all the charges etc., complete.

Providing 15 mm thick Cement Plaster in single coat on rough side of single or half brick wall for interior / exterior plastering up to floor two level, including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80 mm in girth and finished even and smooth in CM 1 : 4 including supply of all labours, tools, materials, etc. complete as directed by the engineer in charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50m and lift upto 1.5m.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand) Including supply of material and labour charges etc complete for kerb wall.

Providing and laying factory made chamfered edge Cement Concrete paver blocks (Rubber moulded) in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilever1

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing Steel reinforcement (Thermo-Mechanically Treated bars) of Fe 500 approved brand / grade for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Providing and fixing White Vitreous China Wash basin size 630x450 mm fixed over white vitreous china pedestal completely recessed at the back for the reception of pipes and fittings. with a single 15 mm C.P. brass pillar tap with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste pie of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require as directed including supply of all materials, labours, tools etc. complete as directed by the engineer in charge (Brand: Parryware, Hindware, Neycer).

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as directed by the engineer in charge.

Providing and fixing PTMT 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88mm, weighing not less than 190 gms complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour complete as directed by the engineer in charge.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance (approved quality) from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing white vitreous china pedestal type water closet (European type) with white solid plastic seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.l.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as directed including supply of all materials, labours, tools etc. complete as directed by the engineer in charge. (Parryware -C8935-(S-290))

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, complete as directed by the engineer in charge. (Brand: Parryware, Hindware, Neycer).

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 610x510 mm bowl depth 200 mm,complete as directed by the engineer in charge.

Demolishing R.C.C Work manually/ by mechnical means including stacking of Steel bars and disposal of unserviceable material with in 50 meters lead as per direction of engineeer in charge.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in?Charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead Of area 3 sq. metres and below.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Providing and fixing Glazed tiles for walls Dadoing/Decorative tiles Concept type design tiles Dadoing for washroom, Anti Skid tile flooring are confirming to IS: 13753 of minimum thickness 10mm of approved make like (NITCO, Orient, Somany, Kajaria) or equivelent in all colour, Glazed tile of size 300mmX450mm & floor tiles 300 x 300mm thk after spreading & leveling with C.M. 1:3 of thick 20mm (avg) & pointing with white cement of approved quality admixture with colour pigment etc. as directed including supply of all labour, material, curing, tools& plants etc. complete.

Providing & fixing ceramic Antiskid tiles of approved 1st quality, size and colour (300 x 300)

Decorative concept design tiles for walls of bath room walls, toilets etc., (300mm x450mm)

Providing and fixing 18 mm thick gang saw cut Granite of any colour and shade, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

For Flooring a nd skirting

Nosing on edges

Replacement of damaged netlon mesh of windows, ventilatiors, meat safe, shutters etc and as wherever directed including removing the damaged netlon mesh and refixng with new ones with teak wood being, including disposal of unserviceable materials etc, supply of all labours, tools, materials, etc. complete

Providing 15 mm thick Cement Plaster in single coat on rough side of single or half brick wall for interior / exterior plastering up to floor two level, including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80 mm in girth and finished even and smooth in CM 1 : 4 including supply of all labours, tools, materials, etc. complete as directed by the engineer in charge. (For roof tiles laying)

Providing and laying in situ seven course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Applying interior Emulsion two coats on Ceiling, inner wall with oil bound washable distemper of approved brand and manufacture to give an even shade surface, by brooming the surface to remove all dirt, dust mortar draps and other foreign matter etc. including cost of brushes labour, materials, & ladder and all other charges etc., complete 1.Q, P.H land Staff auauters. (Brand Asian/Berger)

a) White/colour washing

Painting two coats Exterior wheather coat paint APEX ULTIMApaint with First quality of approved manufactures on undecorated wall surface, ceiling surface to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar draps and other foreign matter etc., applying one coat of cement primer including the cost of supply of all labours, materials, tools & plants, scaffolding and ladder,brushes puttywhere ever required and all other charges etc., complete. (Brand Asian/Berger)

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.(Brand Asian/Berger)

Painting two coats with sy.enamel paint to the wooden surfaces. (Brand Asian/Berger)

Applying two coats of sy. Enamel paint of approved quality and colour to steel surfaces as directed. (Brand Asian/Berger)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.(Concealed work, including cutting chases and making good the walls etc.)

a)CPVC pipe20mm dia

b) CPVC pipe 25mmdia

c) CPVC pipe 32mmdia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.(External work).

a) 65 mm nominal dia Pipes

b)100 mm nominal dia Pipes

Providing and fixing PVC 100 mm / 150 mm dia fittings like Tee,Bend,Reducer and other accessories

P/F.100 mm PVC bend

P/F .100 mm PVC "T"

P/F. 100 mm dia PVC Shoe

P/F. PVC Reducer 100mm x 100 mm x 75 mm

P/F. PVC floor trap (Nahini trap)of size 110mm.

P/F PVC Slotted vent cowl of size 100 mm dia

P/F. PVC 100 mm dia door bend

Providing and fixing water supply fittings like Taps,Valves,etc., (Brand: Jaquar, Parryware)

C.P. brass 15mm dia long body bib cock

P/F. C.P Brass 15 mm dia tap (Short body)(Two way):-

Providing and fixing pillar tap (Bib cock)

P/F. C.P brass 15 mm dia Stop cock:-

P/F. C.P.Shower arm - 230 mm long.

P/F. C.P Brass 100 mm dia. Shower rose.

P/F. PVC 15 mm dia Flexible connection pipe for W.Basin.

P/F. 20 mm dia G.M Wheel Value

P/F. 25 mm dia GM Wheel valve.

P/F. 32 mm dia G.M Wheel Valve for Pump room/ inlet/ outlet for Oh tank

40 mm dia non return valve

32 mm CP Waste coupling for sink (Kitchen)

P/F. 15 mm dia Lead flexible Pipe for Geycer.

P/F of Health fauset With Hose

Replacing the damaged pipe fittings

a)15mm dia cp brass bibcock

b)15mmdia cpbrass stop cock

c)15mm dia cp brass pillar cock

d)32mm dia Angle valve ( Conceled)

Providing and fixing good quality Second class teak wood wrought frames of Doors & Windows with M.S. hold fast fixing in Cement conrete 1:3:6 (1 Cement, 3 Coarse sand, 6 Stone aggregate of 20 mm cum down gauge) as per drawing at all heights including supply of all labours, tools, materials and finishing etc. complete as directed by the engineer in charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, Including 12mm thick water proof Playwood etc., panelling, all complete as per direction of Engineer-in-charge and as Per Drawing (Note:- Butt hinges and necessary screws shall be paid separately).

35mm Thick Door Shutters

Providing and fixing M.S. rod with 16mm dia of required pattern in Fixed to openings /wooden frames with rawl plugs screws etc frames of windows etc. with M.S. flats, square or round bars etc. including priming kg coat with approved steel primer all complete. ( for windows and ventilator)

Providing Frosted glass panes 4mm thick louvers (not exceeding 0.2 Sqm ) are provided in flush door shutters for ventilator,Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door shutters to be measured).

Renewing glass panes, with wooden fillets wherever necessary Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and Fixing of wall to wall enclosure with 2 fixed glass and 1 openable door in between with square hardware and profile finished with black glass 8 mm thick fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Providing and fixing Chromium Plated brass Napkin Holder of approved ISI mark and quality with C.P. brass brackets fixed to tiles wall with wooden plugs & C.P. Brass Screws near wash basin etc. including supply of all labours, materials, tools etc. complete as directed by the engineer in charge

Replacement of Unserviceable/broken fitting of doors,windows,Ventilators, Cupboards of shutters and as wherever directed with new aluminium fitting (Heavy Duty) ISI makie, fitted with brass screws, including removing damaged fitting and disposing unserviceable materials from the site etc, supply of all materials, labours, tools, etc.Complete.

100mm SS. butt hinges Heavy duty

75 mm SS. butt hinges.

Al tower bolt 200 x10mm.

Al. tower bolt 150 x 10mm.

Al tower bolt & eyes 150mm.

Al.hasp & staples 150mm.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 12.50mm thick Gypsum Board false ceiling conforming to IS-2095- Part with design work in two level as directed by the Engineer in charge as per the site condition, at all heights including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120gms/sqm(both sides inclusive) as per IS : 277 , consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm , at 1200mm centre to centre, one flange fixed to the ceiling with dash fasteners 12.5mm dia x 50mm long with 6mm dia. Bolts, other flange of cleat fixed to the angle hangers of 25mm x 10 x 0.5mm required length with nut and bolt of required size and other end of angle hangers fixed with intermediate G.I channels 45x15x0.9mm running at spacing of 1200mm c/c to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, 450mm c/c , shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clips made out of 2.64mm dia. x230mm long G.I wire at every junction, including fixing perimeter channels of 0.5mm thick, 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to the wall/ partition with the help of rawl plugs at 450mm centre, with 25 mm long dry wall screws at 230mm. intervals, including fixing gypsum boards to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230mm c/c including jointing and fixing to flush finish of tapered and square edges board with recommended joining compound, jointing tapes, finishing with jointing compound in three layer covering 150mm on both sides of joints and also including the cost of making opening for light fittings, grills, diffusers , cutouts made with frame perimeter suitably fixed , all completed as per specification including providing of molding for light opening , cornice P.O.P all as per drawing and as per direction of Engineer in charge, including supply of all materials, labours, tools and plants and all other charges etc., complete. (The payment will be made for plain area only. No additional payment will be made for design work.The rate may be quoted including design of work). The false ceiling design shall be got approved from the DLL, before execution of work.

Providing and fixing of I class hard wood pelmet boxes over doors & windows as per existing design including woodern polish of 3 coats etc., removing of all dirt, dust etc., supply of all labours, tools, materials, etc.complete.

Polishing with frame polish on previously polished wood and wood surface to given an even surface including cleaning the surface of all dirt, dust and sand smooth etc., supply of all labours, tools, materials,etc. coimplete.

single cot

Sofa set-3 seater

Sofa set-1 seater

Chairs

Teapoy

easy chair royal

easy chair ordinary

Wooden meat safe

wooden Dinning table

Wooden Dinning chairs

Supplying and fixing C.I. cover with frame for manholes :455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. Cost including supply of all labours, tools, materials, etc. complete

Providing and fixing stainless steel ( Grade 316) railing made of Hollow Stainless steel hand rails fabricated out of 316 grade stainless steel flats and tubes, including cutting old damaged M.S railings from supporting RCC pillars of balconies, stocking in ground, fabricating new handrails, polishing, hoisting the new S.S rails to required position, fixing them with RCC pillars with 55 anchoring fasteners, finishing all as per drawing and as per direction including supply of all materials, polishing, fabricating, transporting, fixing, all other charges etc., complete.

Supplying & fixing sintex water tank of three layer (white colour) 1000 lits capacity including transportation, mateials, labours, fixing, tools & plants and all other charges etc complete

cleaning of septic tank by removal of slugde mechanically or by manually and disposal of the same as directed as per the conditions. Cost including labour, materials, tools & plants etc all complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.Cost including supply of all labours,tools, materials, etc. Complete.

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with 6 rows of G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.

Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead.

Providing and fixing of GI pipes for roof truss ,the zinc coating in the tubes must comply with IS 4736 The Gi pipe to be screwed, must be galvanized before screwing.the truss work including welding, zinc coating and all kind of works.all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge.

Providing and fixing of GI pipes for roof truss ,the zinc coating in the tubes must comply with IS 4736 The Gi pipe to be screwed, must be galvanized before screwing.the truss work including welding, zinc coating and all kind of works.all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge.ss flat bar 60x 400mm , ss pipe 19.5 @ 2mm thickness fabrication charges etc., as per the drawing and as directed.

Providing and fixing of GI pipes for roof truss ,the zinc coating in the tubes must comply with IS 4736 The Gi pipe to be screwed, must be galvanized before screwing.the truss work including welding, zinc coating and all kind of works.all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge and as per drawing.

Providing & fixing at all heights, levels and locations Mill finish aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).

0.91mm Aluminium profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm asper drawing and as directed.

M Rajagopal

s.srinivasan

M/s MSK Construction