Supply of Machinery Equipment

Amount

Electronics & Communication Engineering

Instrumentation & Transducer Trainer Kit Input Transducers Onbard: Carbon track, wire-wound and precision rotary potentiometers. Slide potentiometers. NTC Thermister. Type 'K' thermocouples. I.C. temperature sensor. Photoconductive cell. Photovoltaic cell. Phototransistor. PIN photodiode. Linear variable differential transformer. Linear variable capacitor. Strain gauge. Air flow sensor. Air pressure sensor. Slotted opto sensor. Reflective opto sensor. Inductive proximity sensor. Hall effect sensor. Precision servo potentiometer. Techo-generator. Humidity sensor. Dynamic microphone. Ultrasonic receiver. Output Transducers Onboard: Heater. Filament Lamp. DC motor. Solenoid air valve. Ultrasonic transmitter. Buzzer. Loudspeaker. Relay. Solenoid. Counter/timer unit with LED display. Bargraph voltage indicator. Analog 10V center-zero meter

Microwave Bench(Klystron based) Includes Klystron mount with tube, Klystron Power supply, VSWR digital meter, frequency meter, variable attenuator, detectror mount and other standard accesories including magic tee, directional coupler and horn antenna

Digital IC trainer Kit: Built in power supply providing regulated DC for operation At least 8 Logic inputs switches At least 8 LEDs for observing output Components Onboard: NOT, AND, OR, NOR, NAND and XOR gates 4 Bit Universal Shift Register 4 Bit Adder/Sub tractor Flip Flops - RS, JK , Multiplexer, De multiplexer Encoder, Decoder Onboard Seven segment Display with inbuilt decoder IC Patch Cords (at least 30)

EPROM Programmer: USB 8051 Programmer AT89C series and AT89S series from Atmel. Supports 8 pin serial EEPROM ICs, Single ZIF socket for easy insertion and removal of ICs for programming. Software compatible with Windows 10

Experimental kit for Error detection & correction using Hamming code with built in power supply; On Board Digital Data signal generator and clock generator and a word length of 8, or more; with on-board noise insertion circuit and data receiver

Experimental kit for study of parallel to serial data conversion using USART 2) with built in power supply; On Board Digital Data signal generator and clock generator and LEDs for observation of Input and Output

Experimental kit for study of Time division Multiplexing & De-Multiplexing with built-in power supply, variable on-board data signal generation and LED Indication for outputs

Experimental kit for study of FSK modulation & Demodulation 4) with built-in power supply, variable on-board data signal and carrier generation and different test points for observation of waveforms

Experimental kit for study of ASK modulation & Demodulation with built-in power supply, variable on-board data signal and carrier generation and different test points for observation of waveforms

Demonstration kit of Inverter/UPS with different test points for observation of waveforms and troubleshooting using block diagram approach; including all accessories with batteries and power adapter

Experimental kit for plotting frequency response of a microphone With built-in power supply & Amplifier

Experimental kit for plotting frequency response of loud speaker With built-in power supply & Amplifier.

Three phase Transformer: Operation of three phase transformers each of capacity 10 KVA, with provision for Star- Delta connections including Panel Board and all accessories.

DC Shunt motor coupled with Dc Shunt Generator: DC Shunt Motor 5 Hp including control panel board with starter

3-Phase Squirrel Cage Induction motor: 3-Phase Squirrel Cage Induction Motor with star –Delta starter 5HP, 440 V, 50 Hz, 1500 rpm including control panel Board and its loading arrangement.

Single phase Induction motor: Single Phase induction motor, 220V 2 HP including Panel Board, Wattmeter and power factor meter of suitable rating.

AC Distribution panel Single Phase 10 way MCB’s & RCCB 32A, 16 way (with pilot lamps and fuses)

AC Distribution panel 3-phase 4 wire distribution with MCB & RCCB’s 32A, 16 way (with pilot lamps and fuses)

DC Distribution Panel 240V DC, 16 way (with pilot lamps and fuses)

Tachometer capable, Analog Type/Digital type capable of Measuring speeds upto 20,000 RPM and above.

Single Phase Capacitor start and run Motor, 220V 2 HP including Panel Board, DOL starter and all accessories.

Stepper Motor 220V 0.5HP including Panel Board and all accessories

Servo Motor 220V 0.5HP including Panel Board and all accessories

AM Transmitter: Audio Oscillator with adjustable Amplitude & Frequency (300 Hz - 3.4 KHz), Audio Output: Amplifier with speaker Modulators: Balanced Modulator with Band pass Filter (1 MHz) - 2 nos., Balanced Modulator: 1 No. (455 KHz) Ceramic Band pass Filter: 1 No. (455 KHz), carrier Frequency : 1 MHz, Transmitter Amplifier Output gain adjustable) DSB (1 MHz), SSB (1.445 MHz) connected to Antenna/cable

Radio Receiver: Superhetrodyne type Rx, Frequency Range : 980 KHz to 2060 KHz, Intermediate Frequency : 455 KHz Tuning with variable capacitor (ganged), Dial marking on board, Receiving media : Telescopic antenna / Cable Audio Output : Amplifier with speaker Automatic Gain Control : Switchable

PCB Design & Fabrication complete Setup: PCB Art Work Film Maker, Artwork Table , PCB Shearing Machine , Photo Resist Dip Coating Machine , UV Exposure Unit , Dye Tank , Development Tank , PCB Etching Machine, Drill Machine , Solderable Lacquer, PCB Designer Kit , PCB Curing Machine

Digital IC trainer Kit: Built in power supply providing regulated DC for operationAt least 8 Logic inputs switches, At least 8 LEDs for observing output, Components On-board:NOT, AND, OR, NOR, NAND and XOR gates, 4 Bit Universal Shift Register,4 Bit Adder/Subtractor,Flip Flops - RS, JK Multiplexer, De-multiplexer, Encoder, DecoderOn-board Seven segment Display with inbuilt decoder ICPatch Cords (at least 30)

Amplitude Modulation & De-Modulation kit: Audio Oscillator(Sine Function) Output : 0-10 VPP , Frequency : 200Hz - 10 KHz,Carrier Output Frequency(Sine & Cosine),Output : 0-10 VPP, Frequency : 2KHz- 100 KHz, Modulator, Phase Locked Loop detector , Low Pass Filter:10 KHz cut-of frequency. Output Amplifier with adjustable Gain; with provision of obtaining DSBSC, SSB modulation using jumpers on the same kit.

PAM kit: Pulse Output (frequency) : 8kHz, 16kHz, 32kHz ,Function Generators: Sine wave & Square wave with Gain Adjustable

PWM kit: Pulse Output (frequency) : 8kHz, 16kHz & 32kHz, Function Generators: Sine wave & Square wave with adjustable gain ,Voice Communication : Voice Link using Dynamic Mini Microphone & Speaker,AC Amplifier : With adjustable gain

PCM kit: Audio codec : Stereo Inputs : Single ended Number of bits per channel : 16 bits (Left and Right)Sampling Rate : 48, 24, 12 and 6 KHz System clock : 256 x (Sampling clock) Clock Source on-board, Analog Signal Sinusoidal with Frequency up to 3.3 KHz and Amplitude 0 - 5 Vpp

Cathode Ray Oscilloscope Two Channel Channel I & II alternate or chopped, X-Y operation,(Ratio 1:1 Input via CH II), Add/Sub CH I ± CH II, Invert CH II, Intensity and Focus Control, X-pos, Y-Pos controlsBandwidth : DC -30 MHz,Trigger Bandwidth : 40 MHz,Modes : Auto/ Level.Source : CHI, CH II, ALT-CH I/ CH IIExt. Slope : Positive or NegativeComponent Tester (built in)Display : 8×10 cm. Signal coupling modes - DC, AC. Calibrator : Square Wave generator 1KHz, approximately, 0.2 V. Included Accessories : BNC to BNC -2No.s, 1X/10X. Switchable probes - 02No.'s

Digital Storage Oscilloscope Bandwidth - DC to 200 MHz,Number of Channels: 2, CH +1 Ext (or more).Acquisition Modes: Normal/Average/Peak Detect. Input Coupling - DC, AC and GND.Trigger Sources: CH1, CH2, Ext. AC LineTrigger Modes: Auto, Normal, SingleVertical sensitivity: 500µV/DIV to 10V/Div. Maths functions : +, – , ×, /, FFT. Power: 100 - 240V AC. Accessories: 1:1 Probe (2 pcs), Power Cord, USB CableSize of Jaw 4” (or 100 mm).

DSB /SSB Transmitter trainer kit. Oscillator : With adjustable Amplitude & Frequency (300 Hz - 3 KHz) Audio Output : Amplifier with speaker Modulators : Balanced Modulator with Band pass Filter (1 MHz) - 2 nos. Balanced Modulator : 1 No. (455 KHz) Ceramic Bandpass Filter : 1 No. (455 KHz) Carrier Frequency : 1 MHz (Oscillator controlled) Transmitter Amplifier Output : (Gain adjustable) DSB (1 MHZ), SSB (1.445 MHz) connected to Antenna/cable Switched Faults : 8 nos. Interconnections : 2mm Banana socket Test Points : 27 nos Power Supply : 110-220 V AC ±10%, 50/60Hz Power Consumption : 4 VA approximately Dimensions (mm) : W 326 × D 252 × H 52 Weight : 2 Kg. approximately Product Tutorial : Online (Theory, procedure, reference results, etc). Included Accessories : Patch Cord 16" : 2 nos. Mains Cord, TechBook Power Supply, Microphone, Earphone:1

Optical Fibre Training Kit. Transmitter : 2 No.,Fiber Optic LED having peak wavelength of emission 660 nm & 950 nm Receiver : 2 Nos., Fiber Optic Photo detector Modulation Techniques : 1. AM / FM 2. PAM/PWM/PPM Drivers : 1 No. with Analog & Digital modes AC Amplifier : 2 Nos. Clock : Crystal Controlled Clock PLL detector : 1 no. Comparator : 2 nos. Filters : 2 nos. 4 order Butterworth. Analog Band Width : 100 KHz or above Digital Band Width : 1MHz or above Function Generator : Sine wave (Amplitude adjustable) Optical Power Meter, 5 meter fiber cable(650/660/950nm), 10 meter fiber cable(650/660/950nm).

Prototype (constant K) low pass filter experimental Kit Measurement of the following: characteristic impedance, attenuation, Cut- off Frequency

Prototype (constant K) high pass filter experimental Kit Measurement of the following: characteristic impedance, attenuation, Cut- off Frequency

Prototype (constant K) band pass filter experimental Kit Measurement of the following: characteristic impedance, attenuation, Cut- off Frequency

M-derived low pass filter experimental Kit Measurement of the following: characteristic impedance, attenuation, Cut- off Frequency

M-derived high pass filter experimental Kit Measurement of the following: characteristic impedance, attenuation, Cut- off Frequency

Crystal filter experimental Kit Measurement of the following: attenuation, Cut- off Frequency

Transmission line Trainer Kit Measurement of the following: SWR and characteristic impedance of the line.

Instrumentation amplifier Trainer Kit Measurement of gain,input impedance and o/p impedance of instrumentation amplifier.

Thevenin’s theorem Kit Experimental kit for the verification of Thevenin’s theorem with suitable voltmeters

Norton’s theorem Kit Experimental kit for the verification of Norton’s theorem with suitable meters

Ohms law kit Experimental kit for measurement of resistance by Ohm’s law

Kirchhoff's Current law kit in dc circuit Experimental kit for the verification of kirchoff current law with ammeters

Voltage Laws in a dc circuit Experimental kit for the verification of kirchoff voltage law with suitable voltmeters

Amplifier for conference room Wired for min 50 delegates Features:- Amplifier 250 Watts(for conference Hall) 1)USB port for Pen drive 2)Aux Port for playing mobile recording 3)Must have feature of operating cordless mic(Min 3 no ). 4)Speakers(240 watts)-40wqtt/60watt 5)Cordless Mics 6)Chairman unit 7)Delegate unit

PLC Experimental Kit: Allen Bradley PLC Configurable to both 24 V DC & 230 V ac, built in 24V DC power supply With digital and analog inputs & outputs. 16 I/O LED indications on front line panel, 64 k bytes memory. 8 I/O simulating devices(Toggle switch) Provision to interface PLC module with customized system and for student project interface. Relays protected output. Main socket with self illuminated switch and dual fuse protection. All major components is covered with acrylic or transparent sheet. USB based programming. Simulation basedm, 1) Sequential motor starter interface. 2)Star Delta interface, 3)DOL Starter, 4)Water level controller, 5)Reaction vessel interface,6)Resistance welding interface.7) Traffic Light, 8)Car parking interface,9)Piston cylinder interface, Real time working model for automatic sliding gate and Lift control sytem .Ladder programming & PLC to PC Communication software.

8051 universal developmemt platform, MCU : 8051 core DC Power Supplies : : +12V, -12V, +5V & - 5V Crystal Frequency : : 11.0592 MHz Power Supply : : 110V - 260V AC, 50/60Hz Programmer : : Ready to run programmer.

Electrical Engineering

Expt. Board for V-I Characteristics of a Semiconductor Diode and Zener Diode .Experimental Trainer Board comprising of experimental setup for performing V-I characteristics of semiconductor diode(Silicon & Germanium) and Zener Diode .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. Inbuilt Power Supply, Digital voltmeter and Ammeter with connecting leads.

Expt. Board for observation of I/P and O/P wave shapes of a full wave rectifier. Ckt. With (1) Shunt capacitor (2) Series inductor (3) Pie- filter Ckt . . Inbuilt Power Supply along with individual terminals of all components with connecting leads.

CRO 50 MHz Duel beam 5v D.C Output terminal and having component facility.

Expt. Board to measure (a) voltage gain (b) I/P & O/P impedance for an emitter follower Ckt Inbuilt Power Supply, Digital Frequency meter with connecting leads.

Mono stable & astable , bi-stable multivibrator circuit using IC 555 (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for Mono stable & astable , bi-stable multivibrator circuit using IC 555.The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: study pin configuration of IC 555 , Inbuilt Power Supply , Provision to observe the waveform(i/o) on CRO, connecting leads.

Expt. Board for verification and interpretation of truth table for Logic gates Inbuilt Power Supply alongwith individual terminals of all components with connecting leads for AND, OR, NOT, NAND, NOR, XOR, XNOR, Gates.

Trainer Kit for verification operation of a 8- bit D/A converter Inbuilt Power Supply alongwith individual terminals of all components with connecting leads.

8085 micro Processsor trainer Kits User Memory : 8 KB Input : ASCII Keyboard Display : 20 X 2 LCD Power Supply : 110V - 260V AC, 50/60Hz Battery Backup for RAM Learning manual.

8051 Microcontroller Trainer Kit, operating at 11.0592MHZ. EPROM.64KB on chip Flash memory ,Two 16 – bit programmable on chip Timer.50 pin FRC connector for system bus expansion.Facility to connect to PC. Supports Assembly and “C “ language

V- I CHARACTERISTIC OF SCR Experimental Trainer Board comprising of experimental setup for performingV-I characteristics of SCR .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

V- I CHARACTERISTIC OF DIAC and TRIAC Experimental Trainer Board comprising of experimental setup for performingV-I characteristics of DIAC and TRIAC . The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Use of variable frequency Drive kit for controlling the speed of a 3 phase Induction motor Inbuilt Power Supply, Digital voltmeter and Ammeter with connecting leads. Make. Omega / Sigma/ Scientific Systronics/ Aplab /Meco/Testronic

Digital Multimeter Multimeter Digital (for measurtement of ac voltage 0-500v/ Dc voltage-0-750v, current 0-10 A , alongwith component testing facility .

10 KVA ,440/220 V,Three- Phase air cooled Transformer housed in a Ventilated sheet metal case with all winding terminals fixed on the transformer body .

Diesel Generator set 3 phase Silent Diesel generator , 3- Phase , 415v, 50 Hz , 30 KVA , Water coolant

3 HP ,230 V,1500 rpm Dc series Motor With loading arrangement & control Pannel Board having the provision of changing the value of armature resistance and field resistance with ammeter installed for showing the value of Armature current / field current

5 HP,220V DC.1500 rpm. DC Compound Motor With loading arrangement & control Pannel Board.

Single phase Transformer 5 KVA ,220/440 V,Single Phase two winding air cooled Transformer housed in a Ventilated sheet metal case with all terminals out

Synchroscope meter Electronic / Electrical synchroscope

Three phase Wound Rotor /Slip Ring Induction motor 3H.P,440V,50 Hz,1500 rpm. Slipring Induction Motor (with RotorResistance Starter) including Control Pannel Board and its loading arrangement.

Three Phase synchronous Generator 3 KVA,440V,1500 rpm,(3-Phase 4-Wire) Alternator coupled with 5 HP,220V DC.1500 rpm. DC Compound Motor including Control Pannel Board ( also having a provision of Synchronisation on the same panel Board, synchroscope /lamp method)

Synchronous Motor 3 hP, 1500 rpm , 3 Phase synchronous motor with all field and armature terminals brought out. With load arrangement and control panel

Single Phase Capacitor start Motor and Single Phase 1 HP ,220,1500 rpm Capacitor Strart, capacitor run Single Phase Induction Moto with control panel and loading arrangement

Hysteresis Motor Hysteresis Motor 220V 1 HP including Panel Board and accessories.

Transformer Oil test Apparatus Oil Testing Set input 230V,Out Put 0-50 KV,2KV/Sec.

Tachometer Techometer Digital,Non-Contact Type, 0-3600 r.p.m.

Automatic Voltage stabilizer 10KVA, SINGLE PHASE 90-250 /220 + 10% , Digital Display

Single phase Digital energy meter Digital Energy Meter Single phase , 20 A , 220V, 50 Hz

Earth tester electronic Electronic earth tester (with complete Kit) 0- 100Ω Range

Single Phase wattmeter WATTMETERS:- Provided with Knife Edge Pointer mirror scale, Accuracy ±1% :-Portable wattmeter,dynamometerType,fitted in a wooden/PVC box 1/2 A, 300 V /500 25/50A, 150/300 /500V

Megger insulation tester Megger/Insulation Tester 500 V,200MΩ Analog

Single phase Power factor meter Portable power Factor Meter (0.5--1--0.5 range) : (Provided with Knife Edge Pointer mirror scale ) 10/30 A, 150/300 /600V

Current transformer ( Panel Mounting Type) 2000/1-5A

3-phase Resistive Balanced load Resistive Bank 15 KW,440 V,Three Phase , Loading Rheostat housed in a well ventilated metal case with switches &Fuses , all connecting terminals fixed on the body (With Step Variation)

Rheostats Rheostat ( Single Tube) With Carbon Contacts , 25 Ω / 3 A , 110Ω/ 1.5A , 500 Ω / 1A

DC Regulated Dual power supply Regulated Dual power supply 0-30 V / 0-5 amp +/- 15V, 0-5 A

D.C. Ammeters Portable Moving Coil Ammeter(DC), fitted in a wooden/PVC box square type 0-10m A , 0 - 5A , 0- 10/20 A

D.C. Voltmeters Portable Moving Coil Voltmeter(DC), fitted in a wooden/PVC box square type 0-150/300V , 0-300/600V

AC Ammeters Portable Moving Iron Ammeter(AC), fitted in a wooden/PVC box square type 0- 10mA, 0- 10/20 A, 0- 50A

AC Voltmeters Portable Moving Iron Voltmeter(A.C), fitted in a ooden / PVC box, square type 0-150V/300V , 0- 300V/500V

DA and AD Converter kit Experimental Trainer Board comprising of Experimental setup for Analog to Digital and digital to Analog converter The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB

Single Phase Controlled rectifier Kit Single phase half controlled and fully controlled full wave rectifier Using Thyristors (Experimental Board ) Experimental Trainer Board comprising of Experimental set up for SCR based single phase half controlled and fully controlled full wave rectifier. The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities:1.In built power supply with indicator 2. On/Off switch 3.Protection against high current and transients. 4. Provision for observing waveforms on CRO. 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord(min. 4 mm) required for the ETB

Universal IC Tester : IC PACK : Digital ICs up to 40 pins and analog ICs up to 20 pins in DIP package.IC TYPE : Tristate, open collector & bidirectional TTL/CMOS digital ICs also analog ICs as per list. TEST BY : Truth table comparison for digital ICs. Functional test of output for various input conditions for analog ICs. ZIF : 20 pin DIP ZIF for analog ICs and 40 pin Universal ZIF for digital ICs.KEY : 24 keys DISPLAY : 16 character x 2 line SUPPLY VOLTAGE : 230V AC.

TRIAC characteristics Kit Experimental Trainer Board comprising of experimental setup for performingV-I characteristics of TRIAC . The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Signal Generator Operating Modes : Sine, Square, Triangle, Ramp, Pulse, TTL and Serial Data Frequency Range : 1 Hz - 10 MHz Sine wave &1 Hz - 2 MHz others Frequency Accuracy : 0.5 % Frequency Display : 20 x 4 character LCD Output impedance : 50 Output Voltage : 10 Vpp into 50.

Function Generator Range 0.3 Hz to 10 MHz with Sine , Square , Triangle waveforms, Ramp and pulse Square Wave Rise time typ. 70 ns , LED Display

Hartley Oscillator Kit Experimental Trainer Board comprising of Experimental setup for Hartley Oscillator circuit .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities:1. In built power supply with indicator 2. On/Off switch 3. Protection against high current and transients.4. Provision to observe the waveform(i/o) on CRO.5. Operating manual with detail procedure and specifications of components used .6. Suitable numbers of Banana Patch cord(min. 4 mm) required for the ETB. 7. Quality check and calibration certificate for meters used.

Clipping and Clamping Kit Clipper and clamping circuit trainer (Experimental Board ) Experimental Trainer Board comprising of experimental setup for performing clipping and clamping operation .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure.The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Provision to observe the waveform(i/o) on CRO. 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Transistor Characteristic Kits (Common Base and Common Collector).Experimental Trainer Board comprising of Experimental setup for Input & Output Characteristics of Transistor(NPN&PNP) in Common Base and common collector configuration mode .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Single stage transistor Amplifier Kit Single stage Transistor Amplifier Circuit(CE mode) . (Experimental Board )Experimental Trainer Board comprising of Experimental setup for Single stage Transistor Amplifier Circuit(CE mode).The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure and specifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

V- I Characteristic of Field Effect Transistor (Experimental Board )Experimental Trainer Board comprising of experimental setup for performing V-I characteristics of Field Effect Transistor ( FET) .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure.The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3. Digital voltmeter and ammeter 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Washing Machine Semi Automatic 6KG

Electric Oven MICRO WAVE OVEN; Including Grill & Utensils 32L

Electric OTG Furnace Digital PID controller muffle furnace 900 0c 9'' x 4 '' x 4''

Drilling Machine Power Drilling Machine- chuck capacity upto 1’’ make Wolf , (with Bits)

Motor starters 1. D.O.L. Starter upto 5 hP 2. Mannual Operated Star-Delta Starter (For 5-20 HP) 3.Automatic Star-Delta Starter (Above 20 HP) 4. Three point starter 5. Four point starte

Binary Half And Full Adder Experimental Kit Experimental Trainer Board comprising of Experimental setup for Construction of Half Adder and full Adder. The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure. The boardmust include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB.

Binary Half And Full Subtractor Experimental Kit Experimental Trainer Board comprising of Experimental setup for Construction of Half subtractor and full subtractor. The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure. The boardmust include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB.

Flip Flops (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for study of Flip Flops(RS,JK, master slave J-K,D and T ). The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB.

Mona Stable Multivibrator , Astable Multivibrator Circuit , and Bistable Multivibrator Circuit (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for Astable Multivibrator Circuit ,Mono stable Multivibrator and Bistable Multivibrator Circuit .The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB.

Earth Leakage Relay voltage 90-270v AC/DC , BURDEN UP TO 3VA, Current rating 10mA - 30 Ma

Frequency Meter Analog up to 60 HZ ,220V

Coil Winding Machine 15” X 14”, 152-C Coil Winding Machine. (Floor Model) Standard Machine specifications Base Plate size 15'' x 14 '' maximum coil/Bobbin Diameter 8'' Maximum Centre Distance 5 '' Maximum Axial Winding length 4.5'' Wire Range 20-46/16-40/40-36 SWG Motor 0.5 hP 1440 RPM Single Phase Clutch Foot Padle Assembly Fabricated Stand

Cross Sectional Model Of Motor( Cut View Model) Cut View of 3- Phase induction motor

Relay Demonstration Panel

Single Phase Induction Motor along with Panel Board 1 HP,220V , 1500rpm,50Hz Capacitor Start Induction Motor Provision of connecting and disconnecting the capacitor

Synchronous Motor Coupled With DC Generator , 5HP Synchrous motor with 3kw , 220v shunt gen

Tachometer Digital,Contact Type , 0-3600 R.P.M.

Electronic analog Frequency Meter 0- 60 Hz

Rheostat ( Double Tube)160 Ω / 2.8 A

Rheostat ( Double Tube)1350 Ω / 1 A

Cable Jointing Kit : lv/lt heat shirnk type cable jointing kit for 1.1kv, 3.5 core, 17mm2 power cable

Contractor 10A,230V (3N/O,2N/C)

Contractor 10A,230V (4N/O,3N/C)

Contractor 15A,415V (4N/O,3N/C)

Crimping Tool(Hand) Hand crimping tool 10mm2

Instrumentation and Control Engineering

PLC Automation Lab Set Up - System Specification: - PROGRAMMAMBLE LOGIC CONTROLLER (PLC) - Make: - ALLEN - BRADLEY/SIEMENS/MITSUBISHI - Micro 810 Series 2080 - LC10 -12AWA or Equivalent - Micro 810 controller Input /Output :- 8 INPUTS (4 Digital,4 Analog/Digital ,Configurable) and 4 Outputs (Relay) - Output:- Total Four with Two Relay at 8 A @ 240V AC and General Use , Other two Relay at 4 A @ 240V AC, General Use - Power Rating:- 120-240 V AC ,50 Hz - PC Interface Facility - PLC interface cable 2080- USB Adapter, USB Adapter Plug for 8010 12- point only - 2080 LCD, 1.5 LCD display and Key Board for micro 810 - Necessary I/P - O/P Simulating devices - Ladder Diagram Programming on PC - SCADA SOFTWARE Connectivity for PLC (Optional) - Electrical Control Panel for Simulation of Digital Circuits

Power Electronics Multi trainer Kit - Operated on mains power supply with inbuilt power supplies of +5V, +12V, 0-15V, 0-30V, 15-0-15V - With analog and digital meters on front panel for dc voltage and current measurements - Power devices to be mounted on panel for their characteristics study: SCR, DIAC, TRIAC, UJT, MOSFET and power diode - On-board resistor bank: rotary switch load resistance, fixed and variable resistances and potentiometer for intensity control applications - On-board capacitor bank - On-board firing circuit: RC firing and UJT firing - Electric bulb of 12V 18 Watt - Interconnection points and interconnection cords.

Optical Pyrometer - Optical Pyrometer: Temperature Range: - -40 degree Celsius to 900 degree Celsius (Rugged and Usable up to 180 degree Celsius without Cooling) -Spectral Range: - 8-14 micrometre - Optical Resolution: - 22:1 - System Accuracy (at ambient Temperature of 23+_ 5 degree Celsius): - +_ 1% or +_ 1 degree Celsius (Whichever is greater) - Repeatability (at ambient Temperature of 23+_ 5 degree Celsius): - +_ 0.5% or +_ 0.5 degree Celsius (Whichever is greater) - Response Time: - 150 milliseconds -Display: - LCD Backlit Display - Analog Outputs: - 0/4- 20m milliampers,0-5/10V, Thermocouple J, K type - Inputs: - Programmable Function Inputs for external emissivity adjustment, ambient temperature compensation, trigger (reset of Hold Function) - Cable Length: - 3 meter - Current Drawn: - maximum 100 m ampere - Power Supply: - 8-36 V DC

TRAVEL & TOURISM

Camping Tents for 02 persons

Camping tents for 03 persons

Sleeping Bags

Inflatable mattresses 02 person

Inflatable mattress 01 person

Hikers cooking set with nontick cationg for 4 persons

Camping Lamps

Mars Edpal Instruments Pvt Ltd

Scientech Technologies Pvt Ltd