Repairing Renovation at GNM School of Nursing, GMCH (Repairing/Renovation of RCC hostel building, GNM School of Nursing, GMCH, Guwahati)

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :15.12.2: Of area beyond 3 sq. metres

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).9.1.3: Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

15 mm cement plaster on the rough side of single or half brick wall of mix :13.2.1: 1:4 (1 cement: 4 fine sand)

Grading roof for water proofing treatment with 22.14.1: Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.(For the purpose of measurement the entire treated surface will be measured.)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):21.3.2: With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:9.95.3: 100x75x4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :9.96.1: 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :9.97.1: 300x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :9.100.1: 125 mm

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :13.43.1: Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :13.60.1: Two or more coats on new work

Applying priming coat:13.50.1 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.62.1: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1.14.1: 12X 1.5 sq. mm+ 1X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2X4 sq. mm + X4 sq. mm earth wire

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 1.23.1: 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing following nodular switclh sockct on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1: 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular Each plate as required.

Supplying and fixing following sizel modules, Gi box along with modular base & cover plate for modular switches in recess etc as required.1.47.1: 1 or 2 Module (75mmX75mm)

3 Module (I00mmX75mm)

6 Module (200mmX75mm)

12 Module (200mmXI 50mm)

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in surface etc as required. 1-2 Module (75mmX75mm)

3 Module (100mmX75mm)

8 Module (125mnXI25mm)

12 Module (200mmX150mm)

Supplying with fitting fixing of surface & wall mounted LED luminaries complete with al! accessories including driver directly on wall / ceiling including connection with .5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (BAJAJ / Crompton / PHILIPS / Havells or equivalent considering the mother items rate and specification) (a) 18W 4ft LED Batten

Supplying including fitting fixing of following A.C. Ceiling fan (ISI Marked) complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department Without regulator). (USHA Or Equivelent 1200mm Sweep

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approvcd by the Deptt.) as required complete and as directed by the Department. (Havells or equivelent make) 450mm Sweep Metal Blade

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Dept.)as required complete and as directed by the Department. (USHA or equivelent make) 225mm Sweep Metal Blade

Supply, Installation, Testing and Commissioning of Constant Beamwidth TechnologyTM Line Array Column Loudspeaker. Drivers Eight 50 mm(2 in) Full-Range, Frequency Range (-10dB) 80 Hz - 20 kHz, Coverage Angle Vertical 20° (1.5 kHz - 16 kHz, ±10), Horizontal 150° (ave, 1 kHz - 4 kHz, ±20°), Sensitivity 93 dB (speech mode, 2 kHz - 14 kHz)89 dB (music mode, 300 Hz - 18 kHz), Impedance 8 ohms, Power Rating 150W (600W peak), 2 hrs, 100 W (400W peak), 100 hrs, Maximum SPL (1m) Speech mode: 115 dB cont ave (121 peak), Music mode: 111 dB cont ave (117 peak). (Make:- JBL )

Supply, Installation, Testing and Commissioning ofTwo- channel, 525 W @ 4 Power Amplifier Make:- Crown

Supply, Installation, Testing and Commissioning of Wireless Handheld Microphone (Make:- AKG)

Supply and Laying of Audio Speaker Cables 2.5 Sqmm (Make:- Gotham / Belden/ Finolex)

Supply and Laying of Audio Signal/ Microphone Cables (Make:- Gotham/ Belden)

Supply, Installation of Audio Connection (Make: Ampohenol/Neutrik),

Supply, Installation, Testing and Commissioning of LED Blinder 400w 4 Eyes Blinder COB Matrix blinder audience cob LED light, 4* 100W 3200K party event equipment 1.Light Source :4 pcs 100/100W warm white or cool white or cool white+ warm white 2 in l or white + yellow 2 in 1.Voltage : AC90V - 245V Frequency : 50 60Hz Power Consumption : 450 W Light Color : White or warm White LED Control: Individual Controllable Lifetime : 60,000 hours DMX Channel: 6/12/2CH Color Temp : 2500K /3200K / 6500K Warm White : 5600K - l6400K Cool White : 2800K - 3200K Dimmer :0-100% Linear Adjustable Beam Angle : 38 Degree, Working Temperature : - 30°C-50°C Control Mode : DMXS12, Master / Salve, Auto Run, Stand alone,Sound Active Strobe, Effect : Variable Speed (1-30Hz) House Material Matel House Color : Black IP Grade : IP20 Weight: 5.5 kg

Supply and Laying of 2.5 Sqmm Electrical Power Cable (Make:- Finolex/ Polycab/ KEI)

Supply and Laying of DMX Cable

Sri Dilip Kumar Deka