Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹15.4 LAccepted-AOC MURSTEY COLONY PLOT NO 16 LEH 194101 LADAKH | LEH LADAKH | LADAKH | 194101 | L1 | Accepted-AOC Lowest and reasonable | |
| 2 | L2₹17.0 L+₹1.6 L (10.3%)Rejected-Finance BOGDANG NUBRA PIN 194101 | BOGDANG | NUBRA | LADAKH | 194101 | L2 | Rejected-Finance Other than lowest |
Tender Value
₹20.0 L
EMD Value
₹39,980
Closing Date
13 Jun 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GARRISON ENGINEER (AF) THOISE
GARRISON ENGINEER (AF) THOISE 19 FBSU, c/o 56 APO, PIN 937219
REPAIR/REPLACEMENT OF E/M INSTALLATION AT AF STN THOISE UNDER GE(AF) THOISE
2023_MES_596296_1
GEAF/T-25/2023-24
Open Tender
Civil Works
Item Rate
210 days
GARRISON ENGINEER (AF) THOISE
As per tender document
7 documents required · 7 mandatory
₹500
GE AF Thoise
₹39,980
Yes
22 Aug 2023
18 May 2023
15 Jun 2023
18 May 2023
13 Jun 2023
25 May 2023
Amount
Demolition of cement concrete in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-Charge.
M&L 100 mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in sub base course, floor etc complete all as specified and as directed by Engr-in-Charge.
M&L 200 mm thick PCC 1:2:4 type B-2 using 40 mm graded crushed stone aggregate as in base course, floor etc complete all as specified and as directed by Engr-in-Charge.
M&L for plain cement concrete type B-2 1:2:4 (40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and as directed by Engr-in-Charge.
Dismantling posts & struts; (wood, steel or R.C.C) any section, including taking out embedded portion (embeded in conc) & making good distributed ground, complete all as specified and as directed by Engr-in-Charge.
Dismantling plain or corrugated steel sheeting any gauge, thickness, including nanital or similar pattern roof covering, etc, complete all as specified and as directed by Engr-in-Charge.
S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in roofs, walls etc. with grade of zinc coating 275, etc, complete all as specified and as directed by Engr-in-Charge.
Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed by Engr-in-Charge.
S&F steel work in tubular trusses, as in post, trusses, purlin etc, incl special shaped washer etc, complete using ERW or induction butt welding tubes confirming to IS 1161-1979 grade St-240, including structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as specified and as directed by Engr-in-Charge.
S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, bearing plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engr-in-Charge.
M&L for preparation for new steel Surfaces of any description over 10cm grith or width, not otherwise described, two coat of synthetic enamel paint in comauflauge pattern, over a coat of red oxide zinc primer, complete all as specified and as directed by Engr-in-Charge.
S&F in repair Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, Complete all as specified and as directed by Engr in Charge.
Taking up or down 20 mm steel tubing and connections, including cleaning for refixing or removal to store, Complete all as specified and as directed by Engr in Charge.
S&F 20 mm tubes, medium grade galvanised , with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engr in Charge.
Taking up or down 15 mm steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed by Engr in Charge.
S&F 15 mm tubes , medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors all as specified, Complete all as specified and as directed by Engr in Charge.
S&F in repairs 15 mm Pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, Complete all as specified and as directed by Engr in Charge.
S&F in repairs CP 15 mm Bib taps cast copper alloy, fancy type, with crutch or butterfly handles, screwed for iron pipe or for brass ferrule and fixed, Complete all as specified and as directed by Engr in Charge.
S&F in repairs Angle stop valve of PTMT, 15 mm dia, any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and as directed by Engr-in-Charge.
S&F in repair PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed by Engr-in-Charge.
M&L for preparation of old decorated plastered or unplastered surface of walls etc brooming down with steel wire brushing, scrapping down smoke soot, moulds mass and efforescent salts trading oils etc & greasy spots including concrete plasters etc and applying two coat of white wash on walls, complete all as specified and directed by Engr-in-charge.
M&L for preparation of old decorated plastered or unplastered surface of walls etc brooming down with steel wire brushing, scrapping down smoke soot, moulds mass and efforescent salts trading oils etc & greasy spots including concrete plasters etc and applying two coat of white wash on ceilling, complete all as specified and directed by Engr-in-charge.
M&L for preparation of old decorated plastered or unplastered surface of walls etc brooming down with steel wire brushing, scrapping down smoke soot, moulds mass and efforescent salts trading oils etc & greasy spots including concrete plasters etc and applying one coat of oil bound distemper on wall surface, complete all as specified and directed by Engr-in-charge.
M&L for preparation of old decorated plastered or unplastered surface of walls etc brooming down with steel wire brushing, scrapping down smoke soot, moulds mass and efforescent salts trading oils etc & greasy spots including concrete plasters etc and applying one coat of cement base paint in camouflaging pattern on wall surface, complete all as specified and directed by Engr-in-charge. Note: The pattern of camouflaging shall be approved by GE.
Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, Complete all as specified and as directed by Engr in Charge.
M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beading in square n. exc. 0.5 Sqm in each pane, Complete all as specified and as directed by Engr in Charge.
M&L for preparation of old painted steel surface of any description exceeding 10cm in width and girth and applying one coat of synthetic enamel paint as in camouflaging pattern over rolling shutter lath, steel doors, etc complete all as specified and directed by Engr-in-charge.
Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed by Engr-in-charge.
M& L Screed bed or bedding layer or layer of cement mortar 1:4, 25 mm thick for laying floor finishes, complete all as specified and directed by Engineer-in-Charge.
S & F Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed by Engineer-in-Charge.
Demolition of pre-cast cement concrete block walling built in cement mortar complete all as specified and directed by Engineer-in-Charge.
Material and labour for providing precast cement concrete block of PCC (1:3:6) type-C1 in masonry with solid blocks, as in Manhole, septic tank wall etc, exceeding 10cm in width & set in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.
Taking down cement plaster on brick, stone/concrete surface etc including racking out joints hacking for key scrubbing down with water, etc built in cement mortar complete all as specified and directed by Engineer-in-Charge.
Material and labour for 15mm thick rendering in cement mortar (1:4) on concrete surface of wall is to be finished even and smooth (without using extra cement) complete all as specified and directed by Engineer-in-Charge.
M&L for preparation of newly plastered surfaces and applying two coats of cement base paint as in walls in camouflage pattern complete all as specified and directed by Engineer-in-Charge. Note: The pattern of camouflaging shall be approved by GE.
S & F in repairs 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float, chain and pull and brackets etc complete all as specified and directed by Engineer-in-Charge.
S&F in repair Vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and directed by Engineer-in-Charge.
S&F in repair Vitreous China wash basin, white , flat back, size 550 x 400 mm including cutting for and pinning in ends of brackets or errecting stand and 32 mm waste fittings, brass, chromium plated for galzed ware basin, etc with long screwed shanks and flu-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.
Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.
M&L for Non - skid ceramic coloured tiles 7 to 8 mm thick over 15 mm thick screed bed in CM 1:4, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.
M&L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes as in CM 1:4, Complete all as specified and as directed by Engr-in-Charge.
M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors With grey cement and no pigment complete all as specified and directed by Engineer-in-Charge.
M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of equired strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper mbedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engineer-in-Charge.
Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge.
S&F in repair 4mm thick non asbestos fibre cement building boards fixed or laid in/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frames with shutters exc.1.5 sq.m but n exc 4 sq.m each(without talking off shutters from the frame), complete all as specified and directed by Engineer-in-Charge.
S&F Second Class hard wood plain, solid, straight as in chowkat and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.
S&F for 30 mm thick first class hard wood plain , framed , Panelled Shutters ( any number of panels), with panels of timber flat on both sides(feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.
S&F 100 mm long medium weight, cold rolled mild steel Butt hinges ISI marked complete all as specified and directed by Engineer-in-Charge.
S&F 300 mm Mild steel sliding door bolts, plate type stove enamelled black , with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer-in-Charge.
S&F 200 mm long Mild steel barrel tower bolts, enamelled black, with bright bolt, complete all as specified and directed by Engr-In-Charge. .
S&F 125 mm Mild steel pressed handle, oval type stove enamelled black complete all as specified and directed by Engr-In-Charge.
M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer-in-Charge.
Periodical inspection, checking various parts, greasing/oiling as required to make the sliding steel door/rolling shutters gear/hand operated/electrical operated for easy and smooth operation all as specified and details of sizes and pattern of Mild steel door of any type area exceeding 05 Sqm and not exceeding 30 Sqm, complete all as specified and as directed by Engineer-in-Charge.
S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-Charge.
MEHDI ALI
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .