CONSTRUCTION OF EIGHTY METER STRETCH OF PERIMETER WALL AT BAFFLE RANGE AND SPECIAL REPAIRS TO RETAINING WALL AND DRAINAGE AT BMP GARAGE LOCATION BRICHGUNJ MILITARY STATION, PORT BLAIR

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard dense Soil complete all as specified and as directed.

Excavation in trenches, exceeding 1.5 M deep and not exceeding 3 M depth for foundation, etc., and getting out in hard/dense Soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm in soils complete all as specified and as directed.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and as directed.

Taking down cement plaster on Brick / Concrete surfaces incl raking out joints, hacking for key scrubbing down with water complete all as specified and as directed by Engineer-in-Charge.

Demolition of PCC Block walling built in CM complete all as specified and as directed

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Material and labour Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour pre-cast cement concrete masonry in PCC 1:3:6 type C1 (using 20mm graded aggregate) with solid block, exceeding 10cm in width setting in CM 1:4 complete all as specified and as directed.

Material and labour precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:6 complete all as specified and directed.

Material and labour Providing cement concrete type B1 1:3:6 (Using 20 graded stone aggregate) as in coping complete all as specified and as directed.

Material and labour for RCC M30 design mix for foundation, including rafts, footings, foundation beams; plinth beams; bases for columns etc, basement slabs,, under-reamed piles and mass concrete complete all as specified and as directed.

Material and labour for RCC M30 design mix for column / pillars, post and struts etc all as specified and as directed.

Material and labour Reinforced cement concrete Design mix M-30) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Material and labour for RCC M-30 design mix concrete (using 20mm graded stone aggregate) as in lintel/tie beam/roof beam complete all as specified and as directed.

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter

Use and waste of form work to sides of columns, rough finished surfaces of concrete square, or rectangular all as specified and as directed.

Use and waste of form work to sides of beam / lintel beam and similar structure for flat, rough finished, surfaces all as specified and as directed by Engineer-in-Charge.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Material and labour for TMT bars10 mm dia and over cut to length bent to shape spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.5 mm dia or securing clips etc complete all as specified and as directed

Material and labour for TMT bars 6 to 8 mm dia cut to length bent to shape spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.5 mm dia or securing clips etc complete all as specified and as directed

Material and labour for TMT bars 5mm and over and upto 10mm for stirrups cut to length bent to shape spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.5 mm dia or securing clips etc complete all as specified and as directed

Material and labour rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement.

Material and labour rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

Preparation of old surfaces of Wall and applying one coat of Cement Base Paint on walls all as specified and directed by Engineer-in-Charge.

Material and labour for preparing new plastered surfaces and applying two coats of cement based l paint over a coat of primer complete all as specified and as directed.

Material and labour for preparation of new steel surface of any description, exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

Material and labour for MS Framed work such as in posts & struts etc. including cutting, welding, drilling holes notching for barbed wire etc complete confirming to Fe-290 Grade E-165 complete all as specified and as directed.

Supply and fix for framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tank and similar works conform complete all as specified and as directed.

Supply and fix GI 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs @75mm spacing and straining and fixing including, securing crossing with and including GI wire staples complete all as specified and as directed

DAS AND SONS CONSTRUCTION

Priya construction

T.THIYAGARAJAN

M/S KHUSHICONSTRUCTION

V KARTHICK

Vandana Enterprises

M/S TANISHA ENTERPRISES

RADHA GOVIND CONSTRUCTION