REPAIRS TO WOODEN and STEEL FURNITURE FOR SOLAN, SUBATHU,

Amount

Schedule 'A' Section - I

REPAIR TO CHARPOY GI PIPE 32MM AND CONVERSION/ REPLACEMENT WITH PLY TOP (FD-220)

Long rail;- Re-threading and fixing with elbow after removing and cutting the long rail all as shown on drg and as directed.

Short rail :- All as per description at ser No 1.01 above but to short rail.

Legs :-All as per description at ser No 1.01 above but to legs.

S & F long rail to charpoy GI made out of 32mm dia GI pipe medium grade conf to IS:1239 Part-I of lengh 1.9 mtr after removing the old one.

Cutting , threading and fixing of short rails obtained from long rails at ser No 1.04 above as per drg after removing the old one.

Cutting , threading and fixing of Legs obtained from short rails at ser No 1.05 above as per drawings after removing exising unservicable legs.

S & F of check nut 6mm thick 32mm dia GI to the long rails after removing the old UNSV chek nuts.

S & F 32mm GI elbow 3 way medium gde ISI marked after removing the old UNSV Elbow.

S&F ply wood 12mm thick BWR type size 1980X930 after tightining of frame all as specefied with provision of flat iron of size 40X6mm,900mm long 2 Nos with 65mm long 6mm dia nuts and bolts 8 Nos with washers after drilling complete all as specified after removing the old unservicable nylon newar from charpoy.

M & L for welding to steel frames of furniture articles such as chair CB steel with arms,chair CB steel without out arms, chair verandah, table office clerk steel, form with out back, steel almirah, Table dining OR's, Locker bed side steel etc, including fixing of parts in proper position by preparing the old welded surfaces. welding shall be done through gas welding, the thickness of the metal to be welded n.exe 16 gauge. Length of welding n.exe. 25mm in each point, all as directed.

CHAIR DINING OFFICERS (FD/E6/MAP/10)

Seat made out of 75mm foam cushioned of 40 density covered with Tapestry cloth, cost shall not less than Rs -450/- mtr & Width 1.25 mtr as approved by Engr-in-Charge fixed on12mm thick plywood as base.

Bottom stiffener

Vertical back stiffener

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of chair made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Chair Visitor & Office Type of all models (TP) Repair to chair visitor / Writing Officer & Moulded Fancy with cushion of all models, including repair/replacement of seat, and back, welding of broken joints of frame of chair visitor to make the chair serviceable all as directed.

Seat made out of 75mm foam cushioned of 40 density covered with Tapestry cloth, cost shall not less than Rs -450/- mtr & Width 1.25 mtr as approved by Engr-in-Charge fixed on12mm thick plywood as base.

REPAIR TO ALMIRAH STEEL MEDIUM WITH SHELVES FD-1032

Removing unserviceable shelves of almirah Medium steel & material & labour for providing new shelves made out of PBI sheet 1mm thick cold rolled duly painted with spray paint synthetic enamelled OG/smoke grey over a coat of red oxide primer after preparation of surface & fixing the same with MS clamps,nuts & bolts as shown on drg.

Removing of unserviceable locks, supply & fixing of new lock of approved quality as required having 3 way locking device & duplicate key all as specified in drg

Removing of unserviceable Tala plates, supply & fixing of new Tala plate of approved quality as per drawings.

S&F of CP steel handle & to make the locking device in proper function as specified and shown on drg.

S&F of legs(foot rest) made out of 18G MS sheet to almirah medium steel as per drg after removing the old one

S&F of MS clamps made out of suitable size mild steel flat iron with suitable nuts & bolts as specified in drg.

Removing unserviceable moving rod of almirah medium steel and S & F new moving rod 8mm dia of required length as per drg including making it functional after painting with OG Paint synthetic enameled over a coat of primer.

M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after and painting with one coat of synthetic enamel paint by spray machine to steel items complete of colour/shade as directed by Engr-in-charge and as required :-

REPAIR TO ALMIRAH STEEL LARGE WITH SHELVES FD-1031

Removing unserviceable shelves of almirah large steel & material & labour for providing new shelves made out of PBI sheet 1mm thick cold rolled duly painted with spray paint synthetic enamelled OG/smoke grey over a coat of red oxide primer after preparation of surface & fixing the same with MS clamps,nuts & bolts as shown on drg.

Removing of unserviceable locks, supply & fixing of new lock of approved quality as required having 3 way locking device & duplicate key all as specified in drg.

Removing of unserviceable Tala plates, supply & fixing of new Tala plate of approved quality as per drg.

S&F of CP steel handle & to make the locking device in proper function as specified and shown on drg.

S&Fof legs foot rest made out of 18G MS sheet to almirah med steel as per drg after removing the old.

S&F of MS clamps made out of suitable size MS flat iron with suitable nuts & bolts as specified in drg.

Removing unsv moving rod of almirah large steel and S&F new moving rod 8mm dia of required length as per drg including making it functional after painting with OG/Grey/Silver Paint over a coat of primer.

M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after and painting with one coat of synthetic enamel paint by spray machine to steel items complete of colour/ shade as directed by Engr-in-charge and as required.

REPAIR TO CHAIR VERANDAH FD-359

M&L for re-canning of chair verandah with cane plastic half round 0.4 mm thick Width in matt pattern superior quality as shown on drg and as directed.

M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after and painting with one coat of synthetic enamel paint by spray machine to steel items complete and colour/shade as directed by Engr-in-charge and as required.

Standred white PVC Shoes shall be fixed to Legs.

PAINTING TO STEEL FURNITURE( INTERNALLY & EXTERNALLY):-

M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after and painting with one coat of synthetic enamel paint by spray machine to steel items complete and colour/shade as directed by Engr-in-charge and as required.

INTERNALLY & EXTERNALLY

Locker bed side steel

Table office clk steel

EXTERNALLY

Chair CB steel with arms

Chair verandah

Teapoy verandah

Book shelf open large steel

REPLACEMENT OF CUSHION FOR SOFA SET 3/4/5 SEATER

M&L in replacement of foam cushion size 600x600x100mm, 40 density. Duly covered all over with tapestry cloth superior quality not less than Rs 450/- per R/M as approved. A suitable chain with hook and runner of approved quality one side of the cushion will be provided of the required length as directed by Engineer-in charge.

REPAIR TO CHAIR EASY :FD-229 S & F of following components of chair easy made out of well seasoned sheesham wood all as per drg after removing the old one.

Front leg

Rear leg

Side rail duly holed (Distance of 12.5 mm from one hole to another)

Front rail duly holed (Distance of 12.5 mm from one hole to another)

Back rail duly holed (Distance of 12.5 mm from one hole to another)

Front support rail

Back support rail

Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with lacquer to bring the surface to high glossy finish and as directed by Engr-in-Charge.

REPAIR TO CHAIR WRITING :FD-229 S&F of following components of chair Writing made out of well seasoned Ist class teakwood all as per drg after removing the old one.

Front leg

Rear leg

Side rail duly holed (Distance of 12.5 mm from one hole to another)

Front rail duly holed (Distance of 12.5 mm from one hole to another)

Back rail duly holed (Distance of 12.5 mm from one hole to another)

Long Stiffner

Back support rail

Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with lacquer to bring the surface to high glossy finish and as directed by Engr-in-Charge.

REPAIR TO CHAIR DINING :FD-279 S&F of following components of chair Dining made out of well seasoned Ist class teakwood all as per drg after removing the old one.

Front leg

Rear leg

Side rail duly holed (Distance of 12.5 mm from one hole to another)

Front rail duly holed (Distance of 12.5 mm from one hole to another)

Back rail duly holed (Distance of 12.5 mm from one hole to another)

Long Stiffner

Back support rail

Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with lacquer to bring the surface to high glossy finish and as directed by Engr-in-Charge.

M&L for re-canning to all types of chairs, chair dinning, writing, easy, CBA, CBB, easy NF, stool dressing and bin soiled etc with cane plastic 2mm wide half round with border of 3mm wide in white colour as approved in true godrej pattern as shown in drg after removing the old one.

Repair to Peg Table:FD/271/384

Removing the unserviceable leg and providng the new leg made out of 1st class teakwood seasoned of size 30x50x362mm high and fixing the same in its original position as per drg.

Removing the old broken top rail and providing the new top rail made out of 1st class teakwood of size 20x40x380mm and fixing the same in its original position as per drg.

S&F in replacement of table top for Peg table after removing the old unserviceable top made out of 19mm thick MDF exterior quality one side teakwood faced and other side white balancing confirming to IS-3097 including teakwood beeding 12 mm thick fitted all around duly polished as shown in Drg and as directed by Engineer -in-charge .

Preparation of surface by Removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Table Centre FD-274

Removing unseviceable leg and providing new leg made out of 1st class teakwood of size 60x30x356 mm and fixing the same in its original position as per drg.

Removing old broken top rail and providing the new top rail made out of 1st class teakwood of size20x50x900mm and fixing the same in its original position as per drg.

S&F in replacement of table top for table centre after removing the old unserviceable top made out of 19mm thick MDF exterior quality one side teakwood faced and other side white balancing confirming to IS-3097 including teakwood beeding 12 mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge

Preparation of surface by Removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Table Dining 6 person FD-273/FD/MAP-II/03

Removing unserviceable leg and providing new leg of size 75x40x722mm high and shape made out of 1st class well seasoned hardwood teakwood and fixing the same in its original position as per drg.

Removing the unserviceable top rail long and providing the new top rail of size 25x100x1500mm and shape made out of 1st class hardwood well seasoned Ist Class teakwood and fixing the same in its original position as per drg.

Removing old broken top rail short and providing the new top rail made out of 1st class teakwood and fixing the same in its original position as per drg.

S&F in replacement of table top for table dining six person after removing the old unsv top made out of 19mm thick MDF exterior quality one side Ist Class teakwood faced and other side white balancing confirming to IS-3097 including Ist Class teakwood beeding 12 mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge.

Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Table Dining 8 person FD-373

Removing unserviceable leg and providing new leg of size 75x40x722mm high and shape made out of 1st class well seasoned Ist Class teakwoodand fixing the same in its original position as per drg.

Removing the unserviceable top rail long and providing the new top rail of size 25x100x1500mm and shape made out of 1st class hardwood well seasoned 1st class teakwoodand fixing the same in its original position as per drg.

Removing old broken top rail and providing the new top rail made out of 1st class teakwood of size 1500x900mm and fixing the same in its original position as per drg.

S&F in replacement of table top for table dining eight person after removing the old unsv top made out of 19mm thick MDF exterior quality one side 1st class teakwood faced and other side white balancing confirming to IS-3097 including 1st class teakwood beeding 12mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge

Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Table 3x2 with drawer FD-284

Removing unserviceable leg and providing new leg made out of 1st class well seasoned 1st class teakwood and fixing the same in its original position as per drg.

Removing the unserviceable top rail long and providing the new top rail made out of 1st class teakwood fixing the same in its original position as per drg.

Removing old broken top rail short and providing the new top rail made out of 1st class teakwood and fixing the same in its original position as per drg.

S&F in replacement of table top forTable 3 x 2 with drawer after removing the old unsv top made out of 19mm thick MDF exterior quality one side sheesham faced and other side white balancing confirming to IS-3097 including 1st class teakwood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge.

Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Table Dressing Ladies FD/MAP/II/07

Removing unserviceable legs and providing the legs of size 150x45x45mm made out of well seasoned 1st class teakwood and fixing the same in its original position as per drg.

Removing unserviceable stiffener and providing the new one of size 235x40x25 mm made out of 1st class teakwood and fixing the same in its original position as per drg.

Removing unserviceable top and providing/fixing the new one made out of 18mm thick MDF exterior quality of size 900x380mm with 4mm thick 1st class teakwood beading on front side and fixing the same in its original position.

Remove the ply wood from the back of the mirror and providing the new one made out of 6mm Green ply BWR commercial and fixing the same in its original position as per drg.

Remove the unserviceable broken mirror and providing the new one of size 1220x365x5.5mm thick Make as approved by Engineer-in-Charge and fixing the same in its original position.

S&F in replacement of table top for table dressing ladies after removing the old unserviceable top made out of 19mm thick MDF exterior quality one side 1st class teakwood faced and other side white balancing confirming to IS-3097 including 1st class teakwood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge.

Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge.

Repair to Bed Hard with Ply Top :FD-246/147 Dismantling of old unserviceable components and S & F of new components made out of well seasoned sheesham wood properly planed all as shown in drg :-

S & F Long rail size 1980x100x40mm

S & F Short rail size 840x100x40mm

S & F Stiffner to support ply top of size 835x50x40mm

S&F of head side board of bed bed ply top duly fixed with legs of shisham wood including dismantling of UNSV Compoment all as specified and shown on drg. FD-245/246

S&F of foot side board of bed newar/bed ply top duly fixed with legs of shisham wood including dismantling of UNSV Compoment all as specified and shown on drg. FD-245/247

S&F of 3mm thick sheesham face ply wood BWR gde with head less nails to both sides to the following including sheesham wood beading 6mm thick all around after taking out old one

(i) Head board size 900x442mm

(ii) Foot board size 900x230mm

S&F 12mm thick BWR plywood top in one piece BWR ISI marked to bed hard fixing with 40mm screw wood steel as shown on drg.

S&F MS flat iron clamp size 200x35x6mm long made to shape shall be fixed with six Nos of screw wood steel as shown on drg duly painted with paint enamelled black.

POLISHING TO WOODEN FURNITURE : M&L for preparation of old polished surfaces of any descreption width or girth including cleaning , removing oily spots, ink dots etc and polishing with french polish for glossy finish to the entire satisfaction of Engr -in- charge the tint of polish shall be exactly same as of existing polish colour of furniture or as approved by Engr-in-charge.

Almirah large with shelf

Almirah Medium with shelf

Bed hard with ply top

Book case small

Bin soiled linen

Chair dining

Chair writing

Chair easy

Chair CBA

Chair wooden bottom

Sofa set 5 seater

Locker bed side(Internal & External)

Table peg

Teapoy

Table bed side

Table office officer wooden

Table office clk wooden

Table writing

Table centre

Table dining 6/8 pers

Table 3'x2' with drawer

Table 3'x2' without drawer

Side board

Table Bedside (MAP-15)

Back plywood of 6mm thick commercial plywood of existing shape & size

Drawers made out of 18 mm thick MDF exterior quality with teak wood edging

Chromium plated Handle 100mm long

Telescopic channel of good quality.

Hard Rubber /PVC shoes with steel plate inside of appropriate size shall be provided under legs.

Tube shall be of 18mm square MS Pipe having wall thickness of 18 Gauge.

CHAIR COMPUTER (FD/E6/MAP/01)

Replacement of complete seat & back with new moulded foam cushioned 25 mm thick addn layer & 40 density as shape and size covered with tapestry cloth cost of tapestry cloth/leather finish not less than Rs 450/- RM. of cost as approved along with PVC liping all round, complete all as specified

All as per item No 23.01 here-in-before but for back frame

Hand rest two piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system

TABLE COMPUTER (FD/E6/MAP/03)

Top of 18mm thick pre-laminated MDF board incl PVC lipping all around the top

Drawer of 18 mm thick pre-laminated MDF board fixed with telescopic channel

Shelf for keyboard of 18 mm thick pre-laminated MDF board fixed with telescopic channel .

PVC shoes at the bottom of leg.

Chair Revolving Steel high back (TP)

Replacement of complete seat with new moulded foam cushioned 25 mm thick addn layer & 40mm density as shape and size and fixed over 12mm thick hot pressed plywood, covered with synthetic leatherate as approved and as directed by Engineer-in-charge

All as per item No 25.01 here-in-before but for back frame

Hand rest two piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system

TEAPOY (FD-278/382)

Long rail

Short rail

Side stiffener

Centre stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

Provn of wooden Triangular bracket of size 75x75x30mm at joint of leg and rail of teapoy made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

TABLE 900mm x 600mm WITH DRAWER (FD-1008)

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side MDF exterior quality having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Sofa Set 3/4/5 Seats FD 281/18/373 Supply wood and fixing of the fwg new parts after removing broken/unserviceable parts of well seasoned teak wood including tighting other parts of well seasoned teak wood with screw/bamboo pins only of the sofa complete all as specified in drawing & directed by Engineer-in-charge.

Removal of unserviceable seat and back tapestry cloth and unsv cushion of sofa set three + 2 seater seater and supply and fixing with new cushion according to sofa size of 50 mm thick and 40 Density in additional layer of required length duly covered with well finished best quality tapestry cloth of approved make/shade, cost shall not less than Rs 450/- per metre (width 1.25 mtr) including providing quality ZIP all as specified and shown on drawing and directed by Engr-in-charge

Removal of unserviseable seat and back for Sofa set Three seater of tapestry cloth of not less than Rs. 450 GSM of approved make/shade duly providing quality Zip all asper specified and directed by Engr-in-charge

Amount of credit of Rs. 19102.00 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

M/S SUNIL TRADERS