Construction of PDS Building

Earth work excavation in all classes of soils except hard rock requiring blasting depositing on bank with initial lead of 10M and lift of 2M including all labour charges and incidental charges such as shoring, strutting, providing coffer dams, bailing out of water etc., in SDR Soil- 1st depth

Earth work excavation in all classes of soils except hard rock requiring blasting depositing on bank with initial lead of 10M and lift of 2M including all labour charges and incidental charges such as shoring, strutting, providing coffer dams, bailing out of water etc., in SDR Soil- 2nd depth

Earth work excavation in all classes of soils except hard rock requiring blasting depositing on bank with initial lead of 10M and lift of 2M including all labour charges and incidental charges such as shoring, strutting, providing coffer dams, bailing out of water etc., in SDR Soil-3rd depth

Supplying and Filling foundation and basement with filling M sand in layers not more than 15cm . Thick well rammed, watered and compacted Complete complying with standard specification.

Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed. A) Grade Beam

Filling in Basement with conveyed earth in layers of not more than 15cm. Thick well rammed, watered and consolidated complying with standard specifications etc., complete.

Brick work in CM 1:5mix using country bricks ground molded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. A)For foundation and basement

b) For superstructure in ground floor

Supplying and Fabricating and placing in position MS steel or ribbed steel for all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with standard specification. A) For foundation and basement

Supplying & Erecting centering for sides & soffits including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casuarinas props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items. Centering below Ground level

Rate for column post

Rate for Grade beam ,Lintel

Rate for Roof Beam ,Slab

Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcemeat and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary and bearing surfaces of walls , sides and bottom of the slabs, beams etc., shall be finished smooth with cement mortar 1:3, 12mm thick. and with Kraft paper without claiming extra as directed by the departmental officers complete complying with standard specifications. For foundation and basement

For superstructure in ground floor

Finishing the top of the roof with one course of Machine Pressed Tiles of size 20 cm x 2 cm of approved quality laid in CEMENT MORTAR 1:3(One cement and three sand) 12 mm thick mixed with water proofing compound conforming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar, red oxide, etc., complete complying with standard specification

Finishing the exposed surface of RCC item of work such as slabs, beams, sunshade, facial, canopy slab, staircase waist slab, landing slab etc., with CM 1:3, 10mm thick. including raking the surface. The rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps, landing slabs etc., complete complying with standard specifications.

Plastering with CM 1:5,12mm thick. over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers.

Granolithic Floor finish 1:2:4 mix of 40mm thick HBG metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed.

Paving the flooring with special type of flooring tiles (Cement based Hydraulically pressed Anti skid tiles (20mm thick) in CM 1:3, 20mm thick complying with the standard specifications and as directed by the departmental officers.

Dadooing the walls with glazed tiles of 15 c.m x 15c.m 6mm size laid in cement mortor 1:2 mix 10mm thick and pointing with 0.40 kg white cement per m2 etc.

Distempering two coats with best approved oil bound distemper including cost of painting priming coat over new plastered surface and conveyance of all materials to site and all labor charges

Exterior Emulsion Two coats over priming coat including cost and conveyance of all materials and labor charges etc complete.

Painting two coats over new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with best approved best quality of synthetic enamel paint of approved color over the existing priming coat etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fabrication of the following rolling Shutters including cost and conveyance and all charges etc complete.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,

Fabricating, Supplying and fixng in position of steel sheeted windows ( Two Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.

Fabrication, supply and fixing in position of 'N' type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm 'T' section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising as directed by the departmental officers.

Supply and fixing of 15 A Aerial Fuse unit (500A) unsuitable 100 x 100 Teak Wood Board Concealed box Using Clamps SD-128

Supply and fixing of 16 Amps DPIC switch of 500V grade with Fuse and Neutral on suitable T.W. board with painting of suitable color with PWD Earthling (SD No.154)

Supply and run of 2 of 6 sq. mm ( 84/0.30) polythene insulated and PVC unsheathed S.C. Alu cable of 1100 V on 7/20 Gi bearer wire for Service Connection Main - SD.64

Supply and run of 2 x1.5sq. Mm(22/.3) PVC insulated SC unsheathed CU. Conductor of 1100Grade in 25mm Dia GI PIPE (Glass"B")suitably Bent at both ends with necessary angle iron upright and end supports for Mains SD 69

Supplying and fixing of CFL including all cost and conveyance to work site etc complete

upply and fixing of W.T. Bulk head fitting complete with guard suitable for lamp with 40 W bulb with PVC unsheathed leads from terminal to the fitting - SD. 83

Wiring with 2 x 2.5 Sq.mm PVC unheated SC allocable of 650V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with T.W. Switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable color for concealed PVC light point / Fan Point SD 25

Wiring with 2 x 2.5 Sq.mm PVC unheated SC allocable of 650V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm T.W. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 Amps 3 pin non - interlocking C.S. Plug top with painting of suitable color for open PVC plug point.- SD -36.

Supply and Fixing of Ceiling fan including cost and conveyance of all materials and labor charges etc complete.

Wash Basin

RCC Ring 1.0m dia for Rain Water Harvesting

RCC Ring 1.5m dia for septic Tank

PVC Water Tank

Fabricating, supplying and fixing in positon of SOLID PVC DOORS with frames of different sizes as per the specifications given below: PVC door frames made out of best quality PVC extruded section of 40mm * 58 mm * 2.50 mm +/- 0.3 mm thick, having multichamber cross section and duly reinforced with steel to be mitre cut at the corners and welded including providing tie rod at the bottom and necessary weather seal etc., and PVC door shutters made out of extruded plastic section of 60 mm * 24 mm size in the configruation of an "A" section for shutter frames and multi-chamber hollow plastic section of 200 mm *200 mm*1 mm (average thickness) with tongue and groove section for panels etc., with necessary holdfasts, rubber beedings, furniture fittings, locking arrangements etc., complete including dimantling the masnery, making chippings, holes in the RCC column, beam etc., wherever necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete as per specifications and as directed by the departmental officers.

Conducting Geophysical Survey, quantity and quality test and transportation charges etc., complete

Drilling of bore well anywhere in Tamil nadu including transportation from one place to another place within Tamil nadu in alluvial soil or sedimentary strata of clay and sand or sand, stone, shale, pebbles, boulders etc., y first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia by direct or reverse rotatry mud and circulation method using Contractor's rig, fuel, labour, drilling, betonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit (only Calyx drills are to be used).pg no.198

Supply and delivery of un plasticised 150mm dia PVC Plain casing pipes including, loading, unloading, freight, stacking and transit insurance charges etc., complete TWAD Board pg no.20

Supply and delivery of un plasticised 150mm dia PVC Slotted including, loading, unloading, freight, stacking and transit insurance charges etc., complete TWAD Board pg no.20

Labour Charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including the jointing the pipes with PVC couplers with cement paste etc. complete TWAD Board pg no.313

Supply and delivery of HDPE tank of size 1000 litres capacity bearing with ISI make providing 3 Nos. of 20mm tap connections with check nut washers nipple arrangments and 1 No. of 25mm for scour and 32mm for over flow arrangemetns etc., complete tward board pg.no.92

Supply & delivery of Single phase panel board with two level guard with auto start for 1HP single phase submersible pumpset including cost and conveyance of material etc., complete as per standard specification TWAD Board pg no.313

Supply & delivery of 1 HP Single Phase submersible pumpset Duty 20 lpm x 90 m head, including cost and conveyance of material etc., complete as per standard specification. page no.102 tward board

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required dept valves erection clamps, pressure gauges upto the exterior wall of pump room and erectionof panel board consisting of TPICN switches starter, voltmeter, ammeter, three piolot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules, etc compete and testing the pumpset and train run for 10 days page no.302 tward board 24-25 pg no.204

Charges for developing the Borewell with air compressor of 600 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor as directed by TWAD Officers and conducting yield test by ‘V’ notch method. (TWAD SR

Supply and delivery of PVC insulated and sheathed 3 core 2.5 sqmm flate type copper cable confirming to IS 694/1990 including cost and conveyance of material etc complete as per standard specification.tward board pg.124

Providing kisok of size 75 x 75 x 45 cm made up to MS sheet of 19 guage and MS angle of size 50 x 50 x 3 mm and MS flats 25 x 3 mm for doors withlocking arrangements and fixing over the pedestal of 0.45 x 0.75 x 1.2 m using country bricks etc., complete PG NO.92

Supply, delivery and fixing the following specials in GI and PVC including cost and conveyance of all materials and labour charges fixing in position of specials etc.,complete tward board pg.no.218 a) 50mm HDPE Hosepg.no.218

b) Clamp

c) Borepit

d) 1-1/4" GI Coupling

e) 1-1/4" GM Gate valve-32mm

f) 1-1/4" GM Non return Valve-50mm