Maintenance of Electrical Consumption Charges of Street Lighting on PWD Roads under West Elect. Maintenance Division, New Delhi. (SH- 1. SITC of LED Street Lights at Guru Virja Nand Marg in Hari Nagar Con...etc (FULL NAME OF WORK MENTIONED IN NIT)

Amount

(SH- 1. SITC of LED Street Lights at Guru Virja Nand Marg in Hari Nagar Constituency.) Fabrication, supply and erection of flange mounted hot dip Galvanized Octagonal Poles of 8 mtrs. height made from 4 mm thick HT Steel plate, having minimum bottom dia of 150 mm. & top dia of 75mm. complete with window with hinged cover at a height of 2.5 mtrs from the base for cable termination block etc. and galvanized base plate of nominal size 240mm X 240mm X 16mm thick to suit the existing foundation at site as required.i/c supplying and fixing of the following in the window box provided for cable termination :- a) Supplying and fixing 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. G.I strips 4mm thick of suitable length and having suitable size tapped holes - 10nos. as reqd. b) Supplying and fixing of 40 Amp terminal block suitable for 25sq.mm conductor -4 nos. & shorting links – 5nos. on DIN channel i/c pdg. and fixing DIN channel of suitable length – 2 nos. on the existing laminated sheet. c) Supplying and fixing 6 Amp, SPMCB, ‘C’ Characteristics Curve - 2 No. Earth stud-2Nos. welded at suitable height two nos. washers, springs washers & nuts. d) Cable support clamp suitable for 4 Nos of 4x25 sqmm cable. e) The nuts and bolts shall be welded .The nut-bolts of the foundation shall be covered with cement concrete of ratio 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) upto a height of 30 cm. above foundation.

Providing and laying in position 1:2:4 reinforced cement concrete foundation of size 600 mm.(L) X 600 mm. wide and 1500 mm. deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm. dia- 1660mm long (approx)- 8 Nos. and reinforcement ring of cold twisted bar of 8mm dia - 2200mm (approx) - 10nos. (with 150mm spacing) as required with positioning of foundation bolts (as per item below) and providing 90 mm. (O.D) DWC, HDPE Pipe for cable entry & exit as required. (For 8 Mtr Pole)

Supplying, installation, testing & commissioning of LED street light fixture with IP 66 & IK 07 protection pressure aluminium die cast housing capable of delivering following nominal system lumens output with a minimum system efficacy more than 120 lumens /watt and a CRI greater than 70 . The luminaire shall have a life class of 50000 hours @L70 for a design ambient of 35 deg C . The inbuilt electronic driver shall operate at power factor > .95 of CCT 5700K minimum internal surge protection of 4 KV with toughned glass /polycarbonated cover LM 79/80 certifaction to be provided by the manufacturer for LED luminaire /LED chip .complete etc . as reqd. Not Less than 21000 lumens

Fabirication, Designing, Supplying & Fixing of Galvanized arm bracket 1000 mm long Single / double / triple over hang with tightening bolt etc. as per design approved by Engineer-In-Charge.

Supplying and Drawing following sizes of PVC Insulated and PVC Round Sheathed Multi Core Flexible Copper Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990.

3 x 2.5 sq.mm

Supplying/Laying/Fixing of one number PVC insulated and PVC sheathed/XLPE Al. UG Armoured Conductor power cable of 1.1 KV grade of following sizes in the existing RCC/HUME/METAL pipe/Duct/Surface of Flyover as per instructions of The Engineer-in-Charge as reqd.

4 x 25 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

4 X 25 sq. mm (28mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Providing boring and laying HDPE pipes (ISI marked) of 120mm dia by trench less technology with no dig method by making bore hole in horizontal direction across the road as per direction of Engineer-in-charge with moling equipment i/c jointing cleaning, rodding of pipe providing, suitable covers on mouth of pipes, excavation of pits of required of size at depth 1.30mtr to 2.00mtrs i/c refilling etc. as reqd.

Excavation of the cable trenches in hard rock not exceeding 1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter.

Providing and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment}

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

(SH- 2. SITC of LED and Other Repairing work at Satguru Ram Singh Marg (From SD Public School to Mayapuri Flyover.) Fabrication, supply and erection of flange mounted hot dip Galvanized Octagonal Poles of 12 mtr. height made from 4mm thick HT Steel plate, having minimum bottom dia of 200 mm. & top dia of 100 mm. complete with window with hinged cover at a height of 2.5 mtrs. from the base for cable termination block etc. and galvanized base plate of minimum size 320mm X 320mm X 20 mm thick on existing cement concrete pedestal as required. i/c supplying and fixing of the following in the window box provided for cable termination :- a) Supplying and fixing 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. G.I strips 4mm thick of suitable length and having suitable size tapped holes - 10nos. as reqd. b) Supplying and fixing of 63 Amp terminal block suitable for 25sq.mm conductor -4 nos. & shorting links – 5nos. on DIN channel i/c pdg. and fixing DIN channel of suitable length – 2 nos. on the existing laminated sheet. c) Supplying and fixing 6 Amp, SPMCB, ‘C’ Characteristics Curve - 2 No. Earth stud-2Nos. welded at suitable height 2 nos. washers, springs washers & nuts. d) Cable support clamp suitable for 4 Nos of 4x25sqmm cable. e) The foundation bolts shall have check nuts and nuts shall be welded with the bolts. The nut-bolts shall be covered with cement concrete of ratio 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) upto a height of 30 cm

Providing and laying in position 1:2:4 reinforced cement concrete foundation of size 750 mm.(L) X 750 mm. wide and 1800 mm. deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm. dia- 1960mm long (approx)- 8 Nos. and reinforcement ring of cold twisted bar of 8mm dia - 2800mm (approx) - 10nos. (with 150mm spacing) as required with positioning of foundation bolts (as per item below) and providing 90 mm. (O.D) DWC, HDPE Pipe for cable entry & exit as required. (For 12 mtrs. pole)

Supplying, installation, testing & commissioning of LED street light fixture with IP 66 & IK 07 protection pressure aluminium die cast housing capable of delivering following nominal system lumens output with a minimum system efficacy more than 120 lumens /watt and a CRI greater than 70 . The luminaire shall have a life class of 50000 hours @L70 for a design ambient of 35 deg C . The inbuilt electronic driver shall operate at power factor > .95 of CCT 5700K minimum internal surge protection of 4 KV with toughned glass /polycarbonated cover LM 79/80 certifaction to be provided by the manufacturer for LED luminaire /LED chip .complete etc . as reqd Not less than 33000 lumens

Fabirication, Designing, Supplying & Fixing of Galvanized arm bracket 1000 mm long Single / double / triple over hang with tightening bolt etc. as per design approved by Engineer-In-Charge.

Supplying and Drawing following sizes of PVC Insulated and PVC Round Sheathed Multi Core Flexible Copper Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990.

3 x 2.5 sq.mm

Supplying/Laying/Fixing of one number PVC insulated and PVC sheathed/XLPE Al. UG Armoured Conductor power cable of 1.1 KV grade of following sizes in the existing RCC/HUME/METAL pipe/Duct/Surface of Flyover as per instructions of The Engineer-in-Charge as reqd.

4 x 25 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

4 X 25 sq. mm (28mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.

bituminous portion

Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment}

Supplying & Fixing of Hot molded SMC (Sheet molded Compound) street light pole termination window cover for following size of street light poles complete with rubber gasket. G.I. Mounting strip and bolt for mounting,locking arrangement, color steel grey. Suitable for 12 mtr G.I. Octagonal Pole (having thikness 3mm)

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

(SH: - 3. SITC of LED and Other Repairing work Bhim Sen Marg, Kirti Nagar.) Fabrication, supply and erection of flange mounted hot dip Galvanized Octagonal Poles of 10 mtrs. height made from 4 mm thick HT Steel plate, having minimum bottom dia of 200 mm. & top dia of 100 mm. complete with window with hinged cover at a height of 2.5 mtrs from the base for cable termination block etc. and galvanized base plate of nominal size 320mm X 320mm X 20mm thick to suit the existing foundation at site as required i/c supplying and fixing of the following in the window box provided for cable termination :- a) Supplying and fixing 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. G.I strips 4mm thick of suitable length and having suitable size tapped holes - 10nos. as reqd. b) Supplying and fixing of 40 Amp terminal block suitable for 25sq.mm conductor -4 nos. & shorting links – 5nos. on DIN channel i/c pdg. and fixing DIN channel of suitable length – 2 nos. on the existing laminated sheet. c) Supplying and fixing 6 Amp, SPMCB, ‘C’ Characteristics Curve - 2 No. Earth stud-2Nos. welded at suitable height two nos. washers, springs washers & nuts. d) Cable support clamp suitable for 4 Nos of 4x25 sqmm cable. e) The nuts and bolts shall be welded .The nut-bolts of the foundation shall be covered with cement concrete of ratio 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) upto a height of 30 cm. above foundation.

Providing and laying in position 1:2:4 reinforced cement concrete foundation of size 750 mm.(L) X 750 mm. wide and 1800 mm. deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm. dia- 1960mm long (approx)- 8 Nos. and reinforcement ring of cold twisted bar of 8mm dia - 2800mm (approx) - 10nos. (with 150mm spacing) as required with positioning of foundation bolts (as per item below) and providing 90 mm. (O.D) DWC, HDPE Pipe for cable entry & exit as required. (For 10 mtrs. pole)

Supplying, installation, testing & commissioning of LED street light fixture with IP 66 & IK 07 protection pressure aluminium die cast housing capable of delivering following nominal system lumens output with a minimum system efficacy more than 120 lumens /watt and a CRI greater than 70 . The luminaire shall have a life class of 50000 hours @L70 for a design ambient of 35 deg C . The inbuilt electronic driver shall operate at power factor > .95 of CCT 5700K minimum internal surge protection of 4 KV with toughned glass /polycarbonated cover LM 79/80 certifaction to be provided by the manufacturer for LED luminaire /LED chip .complete etc . as reqd. Not Less than 28000 lumens

Fabirication, Designing, Supplying & Fixing of Galvanized arm bracket 1000 mm long Single / double / triple over hang with tightening bolt etc. as per design approved by Engineer-In-Charge.

Supplying and Drawing following sizes of PVC Insulated and PVC Round Sheathed Multi Core Flexible Copper Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990.

3 x 2.5 sq.mm

Supplying/Laying/Fixing of one number PVC insulated and PVC sheathed/XLPE Al. UG Armoured Conductor power cable of 1.1 KV grade of following sizes in the existing RCC/HUME/METAL pipe/Duct/Surface of Flyover as per instructions of The Engineer-in-Charge as reqd.

4 x 25 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

4 X 25 sq. mm (28mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Excavation of the cable trenches in hard rock not exceeding 1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter.

Providing and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment}

Supplying & Fixing of Hot molded SMC (Sheet molded Compound) street light pole termination window cover for following size of street light poles complete with rubber gasket. G.I. Mounting strip and bolt for mounting,locking arrangement, color steel grey. Suitable for 10 mtr G.I. Octagonal Pole (having thikness 3mm)

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

(SH: - 4. Painting of Street Lights & High Mast Poles on PWD Roads under Hari Nagar and Janakpuri Constituency) Painting of 12/10/8 mtr height GI street pole and mounting bracket with two or more coats of aluminium paint of approved brand & manufacture to give an even shade and Washing/cleaning .etc complete as reqd.

Painting of 20/25/30 mtr high mast pole and mounting bracket with two or more coats of aluminium paint of approved brand & manufacture to give an even shade and washing/cleaning etc complete as reqd.

(SH:- 5. SITC of 30Mtr. High Mast, Near Shadipur Flyover). Supplying, Installation, Testing and Commissioning of 30 Mtr. Height High Mast Tower having in three sections with plate thickness 3mm, 4mm & 5mm Hot dip galvanized and suitable for wind velocity as per IS875, with Bottom dia 460mm and top dia 150mm in polygon structure, comprising of winch (Double drum, SWL 750kg) for raising /lowering. Integral motor push button station, pulleys, Head frame, lighting protection finial & buffers, resting on the foundation bolts duly provided with stiffeners, double locking arrangement for the door and pole installed on the existing RCC foundation complete as per specifications attached i/c supply and fixing following. (a) Hot polygonal structures in three sections. The sections shall be stress/slip fitted without any circumferential weld in between. There shall be only one longitudinal seam weld per section and no circumferential weld. The flanges provided with strengthening gussets between bolt Holes for stiffening complete with raising/lowering mechanism, double drum winch, motor push button station, pulleys, Head frame, lightening protection finial and buffers. – 1 No. (b) Galvanized Lantern Carriage with 12 Nos. arms secured tightly with suitable arrangement for fixing of 12 Nos. Luminaires & other accessories complete etc. as reqd. - 1 No. (c) It shall include 3 point suspension system with accessories for High Mast i/c steel wire rope of 8mm dia (7/19 construction SS316), EPR trailing cable, double drum winch, suitable for 12 luminaries symmetrically & its control gear boxes and lighting finial – Set (d) Moto suitable to operate on 230/415 Volt, 50 Hz 960 RPM detachable type for lowering and lifting mechanism – 1 No. (e) Supplying and drawing multicore, copper conductor flexible power trailing cables of appropriate rating for energizing the luminaries complete as per specifications attached. – 1 Lot. (f) Supply of Foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common plate suitable for 30 mtr. High Mast Pole.) (g) Supply & Fixing of single dome LED aviation light i/c connection complete as reqd. – 1 No. (h) Supply & Fixing of external feeder pillar for 30 mtr. High Mast, Supply operator i/c connection etc. as reqd.

Designing & Casting of suitable open raft type RCC shallow foundation for High Mast as per recommendation of the manufacture adopting the safe soil bearing capacity of site at 10 T/Sq. Mtr. at 2 Mtr. below FGL including positioning of Suitable foundation bolt nut washer, Pdg. straightening cutting, bending rings strictly as per bar bending schedule & drawing complete and PVC pipe of 110mm dia for cable entry at desired level i/c supplying and casting and as per specifications attached. For 30 m high mast

Supply of LED flood light luminaires with wattage < 450 Watt and minimum lumen 53000 in Aluminium PDC housing with clear toughened glass suitable for 240V, 50Hz A.C. supply as required.

Supply of LED flood light luminaires with wattage < 350 Watt and minimum lumen 41000 in Aluminium PDC housing with clear toughened glass suitable for 240V, 50Hz A.C. supply as required.

Supplying/Laying/Fixing of one number PVC insulated and PVC sheathed/XLPE Al. UG Armoured Conductor power cable of 1.1 KV grade of following sizes in the existing RCC/HUME/METAL pipe/Duct/Surface of Flyover as per instructions of The Engineer-in-Charge as reqd.

4 x 25 Sq.mm

Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment}

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

(SH:- 6. Shifting of two nos. High Masts from Hari Nagar Schools to PWD Road in Hari Nagar Constituency.). Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).

All works above plinth level upto floor V level

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Excavation of the cable trenches in hard rock not exceeding 1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter.

Supplying & Drawing of 3 Core 2.5 Sq.mm. PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990. as reqd.

Supplying & Drawing of 6 Core 4 Sq.mm. PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade 1100 Volts as per IS: 694:1990. as reqd.

Supply of LED flood light luminaires with wattage < 300 Watt and minimum lumen 37000 in Aluminium PDC housing with clear toughened glass suitable for 240V, 50Hz A.C. supply as required.

Supplying and Lying of 1 no. cable PVC Insulated & PVC sheathed/XLPE Al. Conductor armoured cable of 1.1KV grade in the existing RCC/ HUME/ HDPE pipe as required.

4 x 25 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 25 sq. mm (28mm)

Supplying and Laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting , jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as. required

63 mm dia (OD-63 mm & ID-51 mm nominal)

Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.

bituminous portion

Fabricating, supplying and fixing of wire mesh protection frame work fabricating with 40 x 40 x 6 mm thick angle iron/Tee iron having intermediate members of size 25mm x 6 mm flat strip welded at 30 cm in each sections & duly welded with hard drawn wire fabric mesh of size 25 mm X 75 mm (GI wire should be 6SWG) having weight not less than 7.5 Kg/Sqmtr. and making main door gate provided with two nos. sliding bolt with 02 nos. godown inter locks with operating hadle welded from inside of the door i/c providing and fixing of four no. legs of same angle size of 90 cm length duly grouted in foundation (30 x 30 x 45) cm (deep) in 1:2:3 cement concrete & painting with one coat of red oxide & two coat of super synthetic luminous paint of approved colour and quality etc. complete as complete as reqd. {Area of hard drawn wire fabric with angle (Except legs) shall be measured for payment}

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal/ coke and salt) as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

M J Electricals and Electronics

HST ENTERPRISES

SM ELECTROTECH PRIVATE LIMITED

DEV ENGINEERS

ACE ENGINEERS BUREAU

SONA ENGINEERS

SACHDEVA ELECTRICALS

Arya Engineers

AJAY MC TOOLS