WBPWD/SE/SWEC/NIQ39/2024-25

Amount

Supply & delivery of 1.1 KV, following size XLPE insulated 1100V grade as per IS 7098 (part-1) 1988 armoured sheathed Aluminium conductor cable as mentioned below. (Make- Polycab/Havells/Gloster/ KEI/RR Kabel as approved by EIC)

(a) 2 core 6 sqmm

(b) 4 core 10 sqmm

(c) 4 core 16 sqmm

Laying of cable upto 2 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting.

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed

Laying only Cable upto 50 sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core

Supplying & fixing 32 mm dia medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials :

(a) 2 core 6 sqmm

(b) 4 core 10 sqmmb

(c) 4 core 16 sqmm

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below :

(a) 2 core 6 sqmm

(b) 4 core 10 sqmm

(b) 4 core 16 sqmm

Supply & Delivery of 9 Mtr Steel Tubular Pole (Zindal /Bansal/ Utkarsh/Calcutta pole) as per specification Type 410 SP -29 as overall length 9 mtr weight 125kg. & having diamention are : Out side dia & thickness of the Bottom section (139.7 x 4.85) mm; Middle;(114.3 x 4.50) mm ,Top Section (88.9 x 3.25) mm with fixing the base plate and GI earth bolt after making drilled holes etc. on pole incl. jacketing arrangement if reqd as per direction of EIC

Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly. Up to 9 mtr Size 0.6x0.6x1.70 mts

providing CC (6:3:1) base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) incl. drilled hole in pole suitable for alkathene/polythene pipe entry, for street light wiring, without Loop Box.

Supply & Fixing of 1.5 mtr long detachable type double arm bracket for pole SP-30/80 mm (ISI-M) pipe pole. The arm bracket shall be properly welded stifner plate of pole sleeve for strengthening including properly fixing arrangement with pole by nut-bolt, washer etc. as per direction of the EIC.

Supply & Delivery 3" dia. 2 Mtr. Long heavy gauge G.I. Pipe (minipole) having 9” X 9” X 1/2" M.S. sole plate welded with drilled hole at bottom of the pole to be installed on roof of building with S.F. grounding bolts. Incl providing CC (6:3:1) base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) suitable for alkathene/ polythene pipe entry as directed for street light wiring, incl. Supply & fixing 50mm Dia 1.5mtr long detachable type GI Single arm bracket suitable for the pole head.The arm brfacket shall be properly welded with 5 mm thick stifner plate of pole sleeve for strengthening including properly fixing arfangement with the pole by bolt, nut, wahser as per direction of EIC. incl. painting by 2 coat of aluminium paint over 1 coat of RO priming

Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper,cleaning etc. for receiving fresh coat of paint.Upto 9.0 mtr. long pole

1st coat of aluminium paint over 1 coat of RO priming

2nd coat of aluminium paint over 1st coat

Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc.

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one 4 way terminal, one compression type brass cable gland for upto 2/4- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

Supply of 240 V timer DB with suitable size sheet steel enclose double door, phosphatised powder coated, neutral bar , din rail with IP-43 protection comprising Timer control for automatic operation of compound lights Consisting of 415V 40A FP MCB - 1 No. , 1 no Astro time switch ( L&T make, cat no- AUTS02AST00/Legrand/ABB), 1 no 40A, 3pole power contractor withh aux NO, NC block (Make- L&T/ Legrand/ABB), wiring by 6 sq. mm. copper wire including 1 no auto manual by pass toggle changer over switch including 1 no LED indicating light for running condition with locking arrangement and outgoing cable terminal. (for controlling Compound Light ) [Make:- L&T / Cabtree / ABB / Legrand]

S & F of 230v, road lighting luminaire (IP 65 or better) with peanut lens and high power LED and to ensure uniform distribution, higher spacing between poles and maintenance free system and system lumen output will be minimum 110 lumen/w suitable for use with 230Volt 50Hz AC supply etc as required on college building front site poles as per direction of EIC.

i) Make- Philips- BRP033 LED120 CW SLR GR PSU SPD or equavalent product of Crompton/ Wipro )

ii) Make- Philips- BRP504 LED210 CW R3C PSU S1 or equavalent product of Crompton/ Wipro )

Inter connection of HPSV/LED fittings by 2 x 1.5 Sq. mm. PVC insulated copper wire from loop box with 19mm bore PVC polythine pipes as per direction of EIC.

Supply of 16M High mast lighting system with its accessories Mast shaft shall be in two sections with steel material confirming to BSEN 10025 and material shall be high tensile steel, grade S355, hot dip galvanized confirming to BSEN ISO 1461 having top dia 150 mm, bottom dia 410mm, sheet thickness Bottom-4mm & top- 3mm, base plate dia 570x25mm suitable for wind speed as per IS 875, with raising lowering system comprising, head frame, Galvanized luminaries carriage suitable to install luminaries in symmetrical arrangement for up to 8 luminaries , double drum winch, 6mm diameter 2 continuous SS wire rope without any jointed or bolted, trailing cable, connector, integral power tool motor incl Supply & Fixing of Cu Cable of Power Tool motor, junction box, lightening finial. Wiring for Luminaries, power cables between panel and mast, MCB in base compartment, Cg mounting clamps and bolts , Anchor Plate, 08 nos. Foundation Bolt (M30 x 850), Nut, Washer, and common Template all complete. luminary mounting bolts are not included. (Make :- Bajaj/Valmont/ Transrail/Lysaght) The following points must be noted and documents must be submitted by the bidder during tender submission: a) Tenderers should note that junction box shall be provided at the top of the high mast and separate control gear boxes for light fittings. b) The high mast should have wind tunnel test report. Relevant documents should be submitted during tender submission by the bidder. c) The Winch Type Test report must be submitted by the bidder from a reputable Government Institute during tender submission. d) The High mast Manufacturer must have Govt. of India recognized Laboratory and Illumination Design Cell. Relevant Supporting Documents must be submitted by the bidder confirming the same during tender submission. e) Relevant ISO Certificates of the manufacturers must be submitted by bidder during tender submission

Design, casting of suitable R.C.C foundation with M-20 grade concrete considering SBC of soil as 10 T / Sq. Mtr. For 16Mt high mast

Erection, testing & commissioning of 16 Mt high mast on the existing civil foundation by bolts with suitable tools, tackles, machines, crane support etc, all complete, as per direction of the EIC. 16 Mt HM.

Supply & fixing of single dome LED aviation lamps.

Supply, Installation & commissioning of mini pillar box of size 800X600X500mm (HXLXB) made from 4 mm thick M.S sheet reinforced with 50X50X5mm angle iron frame work with both side individual hinged door with 1 nos Godrej make 7 lever padlock arrangement with 2 nos earthing arrangement as per direction of EIC. i) The kiosk should have base plate (detachable type with knock out punch for entry cable) ii) There should be hylam sheet of 10 mm thick for fixing of control switch & KWh meter. iii) the kiosk box will have to be painted with lead primer & powder coated synthetic enamel paint. iv)The kiosk should have ventilated window at both side wall v)The roof of the kiosk should be slanting on four side. Incoming:- 415V 40A FP MCCB (DU100D type) with 8 nos spreader terminal make L&T - 1 No. Bus Bar:- 415V 63A 4 nos Cu Bar of 25cm length. Outgoing:- a) 415V 16-32A TP MCB of Breaking capacity 10kA & C characteristics on din rail (Legrand) - 3 nos (light Ckt, Motor Ckt & 1 no spare) b) Timer control for automatic operation of Mast light Consisting of 1 no Astro time switch ( L&T make, cat no- AUTS02AST00) , 1 no 3 pole power contractor ML-2 ( L&T make ), 240V 6A SP MCB of Breaking capacity 10kA & B characteristics(For control Circuit Protection) on din rail complete with wiring by suitable size of copper wire including 1 no auto manual by pass toggle changer over switch including 1 no LED indicating light and outgoing cable terminal.

c) Power tool motor controller comprising of 3 pole power contractor -2 nos with wiring by suitable size of copper wire including 2 nos up & down push botton and outgoing cable terminal to motor. d) Provision for earthing attachment - 2 nos. f) Danger plate - 2 nos. The pillar box has to be installed with brick foundation of size 1000X750X650mm(HXLXB) with hard jhama cement mortar soaling at bottom and 300mm below & 500mm above GL neatly plastered & cemented incl. polythene pipe entry as directed by EIC.

Supplying and fixing 415V, 63A TPN SFU with sheet steel enclosure on flat iron frame on wall with nuts bolts etc incl. S & F 3 nos. 40A DIN type HRC fuse. (Make - L&T/Siemens) at pump room.

Supply & delivery of LED Flood light of following specification: a) 250 W for each set (Maximum). b) System Efficacy of the Luminaries should have minimum 25000 lumens & color temperature: 5700K (+/-)300K, more than 50,000 hrs of life span for LED. c) The fixture shall have Ingress Protection of IP 66 Rating for both for Optical & Electrical Compartments. d) Luminaries should consist of Universal Voltage Driver to handle wide operating voltage range from 120-270V AC and frequency range of 50+/-3% Hz. e) Driver shall have high efficiency and have inbuilt safety features like over voltage , short circuit , over load , thermal protection and reverse polarity protection. f) Surge protection : Inbuilt - 5KV & External - 10KV. g) Luminaries should be powder coated and housed in a single piece Pressure die cast non-corrosive Aluminium alloy enclosure with optimal fins for Heat Sink Mechanism. h) Rated Operating Temperature should be 0 deg to +55 deg C with a relative humidity of 10-95% RH. i) Luminaries shall have five (5) years replacement warranty period from actual date of completion of work including driver/control gear, LED etc. (Make & Model No .: Philips -BVP483 LED259 CW NB A1 PSU GR SPD or equivalent make) for 16M HM .

Fixing only Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI medium GI pipe/ TATA-M

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages. For solid 4 SWG GI wire.

S & D of 18W PC body LED Tube light.(Make - Crompton, Cat - LTT8-20 or equivalent of Wipro/Phillips)

S & D of industrial LED batten for fixing 1200mm retrofit 18/20W T8 tube light

Single Batten(Make - Crompton Cat NoIGP161LT8-16 1 x T8 or equivalent of philips/ Wipro )

Double batten (Make - Crompton Cat NoIGP162LT8-16 2 x T8 or equivalent of philips/ Wipro )

Excavation of soil for installation of Earth Electrode and filling & ramming. (For morrum soil)

M/S JOGMAYA ENTERPRISE (BID ID -5660951)

MODERN ELECTRIC (BID ID -5666570)