GE (AF)/SGR-29/2025-26 REPAIR / REPLACEMENT TO ROLLING SHUTTER, SLIDING SHUTTER, COLLAPSIBLE GATE, SHEETING, PAINTING, PLASTERING, TILING AND CONNECTED WORKS AT OTM, TECHNICAL AREA, BLAST PEN AND WIRELESS UNIT UNDER GE (AF) SRINAGAR

Amount

S&F in repairs for 6mm dia SWR galvanized steel wire rope 6x19 tensile strength 1770 N/mm2 connected to hook etc, complete all as directed and specified

S&F in repairs of mild steel wire rope clamp 8 mm with two bolt size for looping of wire rope, complete all as specified and directed.

S&F in repairs galvanised iron turn buckel of M-16 eye to hook type, body length 170-180 mm, complete all as specified and directed.

S&F in repairs 16mm dia straining bolts / eye bolt including moulding to the required shape and with nut & washers, minimum length 300 mm conforming to FE-290 Gde-E-195 etc, completed all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L for rolled mild steel work in Plates (plain or chequerred ) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410-W (gde-E-250) Quality B complete all as specified and as directed.

M&L for rolled sections Fe-410-W (Gde-W (Gde-E-250) qualty-B , as in framed work for connecting SWR Wires over blat pen main beams and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

M & L Cement concrete Type D2 1:4:8 (40 mm graded stone aggregate) in foundations, filling and mass concrete

M&L for mild steel framed work such as grills, gratings, gates etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed.

M&L for structural steel work as in truss, rafter purling, made out of angle / Hollow pipe / tube section including jointing cleats, plates flat iron, gusset plates, rails, braces etc. conforming to Fe 410-W (gde-E-250) Quality, confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed.

S&F in repairs 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed.

All as per Ser item No 12.00 here in above but except Sheets.

S&F in repairs 0.63mm thick Galvanised, Plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed.

Preparing new zinc (or galvanised) surfaces to receive painting of any description over 10cm width or girth, by coating with mordant solution including washing and cleaning, etc. steel and iron surfaces and applying two coats of synthetic enamel paint in camouflaging CCD pattern as approved, complete all as specified and directed.

Taking down the existing rolling shutters from the existing opening and refixing the same in position after carrying out necessary repairs including oiling, greasing,easing out etc size of shutter exc 7.00 Sqm & n exc 12.00 Sqm each. all as specified and directed by Engr-in-Charge.

M&L for greasing the bottom rail , repair of gap, making the sliding iron door of blastpen in technical area of size exc 30 sqm but n exc 60 sqm each after carrying out necessary repairs including oiling, greasing, easing out etc., complete all as specified and directed.

S&F in repairs hood cover with MS sheet 1mm thick, made to hexagonal square or circular contour and stiffened with angle / flat stiffeners at top and bottom edges and fixed to bracket plate as existing, complete all as specified and directed.

S&F in repairs mild steel safety lever locks with 4 levers for rolling shutters size of lock 100mm, complete all as specified and directed.

S&F in repairs mild steel handle for rolling shutter of size 150mm, complete all as specified and directed.

S&F in repairs rolling shutter gear box made up of worm gear, worm wheel, motor count gearbox case and drive shaft including making the shutter in operating condition, complete all as specified and directed.

S&F in repairs fabricated lock plate of riveted construction made of mild steel sheet of not less than 3.15mm thick, reinforced with mild steel angle section of size 35x35x5mm size at the bottom, interlocked with bottom most lath section of curtain so as to provide contact against the cill, when closed, fitted with sliding bolts with arrangement for locking with pad locks, one handle for widths upto 2.5m, and two handles for widths of above 2.5m, complete all as specified and directed.

S&F in repairs 40mm dia mild steel pipe shaft, heavy duty, complete all as specified and directed.

Preparation of old painted steel and iron surfaces of any description not otherwise described exc 10cm width or girth by brooming down or steel wire brushing, scrapping down, smoke soot moulds, moss and efflorescent salts and greasy spots of roof /CGI Sheets, steel gates, steel doors, steel rolling shutters, steel eves boards etc. and applying one coat of synthetic enamel paint including scaffolding up to 15m height, complete all as specified and directed.

S&F in repairs 1.25mm thick of laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, push pull or manual type, complete all as specified and directed.

S&F in repairs 1.00mm thick of laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, push pull or manual type, complete all as specified and directed.

M&L for Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L welding work for exc 2.5cm and n. exc 5cm in length, thickness of metal to be welded n exc 6mm, welding of hinges, helical door spring, tower bolt clips, MS Flat in steel window for fixing wiremesh etc., complete all as specified and direcetd.

M&L for mild steel works as in holdfast, rails, braces, etc., drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging holdfasts, Grills, cladding and similar small articles conforming to Fe 290 Gde E-165, in repairs, complete all as specified and directed.

M&L for plain cement concrete, 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) for hold fast & similar work etc. including necessary formwork, complete all as specified and directed.

S&F in repairs marathon mild steel wheel, Heavy duty, dia of wheel exc 200mm and n.exc 300mm and width of wheel exc 75mm and n.exc 100mm for hanger door load including fixing to existing or new MS plate of existing size, complete all as specified and as directed.

Taking down and refixing of hanger door of any size for fixing of wheels etc., complete all as specified and directed.

M&L for 100mm thick plain cement concrete, 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in flooring , laid in alternate bays and finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

M&L for forming contraction (Dummy) joint, 65mm deep x 10mm wide as the work proceeds in alternative ways and filled with sealing compound grade 'A' after priming with primer for grade 'A' sealing compound , complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 10 to 12 mm thick vitrified parking tiles in approved shade from meteor series, area of each tile exceeding 0.08 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in matching coloured polymer cement based grout to match over and including 15 mm thick Screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for Glazed ceramic tile 450x 300 x 06-7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc., complete all as specified and directed.

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms with gas pipe hole, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed.

S&F in repairs 15mm bore hot and cold water mixer with swan neck for WHB chromium plated quarter turn screwed down, including necessary fittings, complete all as specified and directed.

S&F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces on brick or concrete surfaces in CM 1:4, fair finished the surfaces even and smooth without using extra cement including scaffolding upto 12m height, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting, on plastered surface preparatory to distempering , complete all as specified and directed.

Preparation of new surface of wall and applying two coats of cement based paint over one coat of primer including scaffolding up to 15m height, complete all as specified and directed.

S&F in repairs for 15mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed.

S&F in repairs for 20mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed.

M&L for Lagging to 20mm bore pipes used in external water supply or plumbing all around with 50mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25gauge 20mm mesh including applying with brushing neat cement slurry with 3 kg of cement per Sqm complete, complete all as specified and directed.

Preparation of old plastered or unplastered wall surfaces and applying two coats of white wash, complete all as specified and directed.

Preparation of old plastered surfaces of wall by washing down, brooming down or steel wire brushing etc. and applying one coat cement base paint including scaffolding up to 15m height, complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfaces of wall including filling of holes, cracks and undulating surface with cement wall care putty making surface even and smooth and applying one coat of distemper oil emulsion paint (OBD), complete all as specified and directed

Preparation of old plastered or unplastered surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. including cornices, pilasters etc. and applying two coats of white (lime) wash, complete all as specified and directed.

Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismantling / taking down items) worth Rs 1,79,170.00 during AOC. (Note :- Tenderers shall not quote for this Schedule)

FG CONSTRUCTION (BID ID -3347830)

M/S LATIF AHMED MIR (BID ID -3346708)

M/S M.R. Construction (BID ID -3351195)

M/s PARVAZ CONSTRUCTION COMPANY (BID ID -3350052)

M/S Abdul Ahad Rather (BID ID -3348137)

M/S FAROOQ AND SONS (BID ID -3358685)

M/S ZAHOOR ENTERPRISES (BID ID -3357370)

M/S WANI AND SONS (BID ID -3348402)