Providing Renovation work of Dog Shelter for ABC Centre in Tharuvaikulam MCC at North Zone Thoothukudi City Municipal Corporation

Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by manual means

Supplying and filling in foundation and basement with well gravel in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Plastering the surface of walls with Cement Mortar 1:4 (One cement and Four plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing of weld mesh conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification -WR-M0075

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by theExecutive Engineer before use on works.)

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(Themake, qualityandcolourof paint shouldbe gotapprovedbytheExecutiveEngineer before use on works.)

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/ m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Fabricting Supplying and fixing in position Aluminium door Powder Coated of size 1.00mx2.10m having Single leaf openable shutter 1/3 panelled & 2/3 glazed with 10 mm thick aluminium grill of approved pattern and design and 12mm thick best quality both sides prelaminated particle board and 5.5mm thick plain glass shall be used for panelling withAluminium section of Outer Frame :101.60x44.45x3.18mm @ 2.319kg/m and Shutter frame of bottom rail : 100x44.45x2.50mm @ 1.974 kg/m,Top & Vertical rail : 50x44.45x2.50mm @ 1.292kg/m,Lock rail: 50x44.45x2.50mm @ 1.292kg/m,Aluminium clips:17.15x17.27x1.50mm @ 0.176kg/m and with required aluminum hinges, door stopper, rubber beading, PVC felt, handle for a length of shutter (both sides) of section: 100x30mm @ 0.988kg/m, locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1No., aluminium tower bolt 200x12mm - 1No., aluminium door stopper with rubber bush - 2Nos ., lock-1No.,Floor Spring - Each.,as per BIS standards including cost of all materials, labour charges and power consumption charges required for fabrication including chipping dismantling and making holes to the required extent in RCC in column/beam/masonry with power drill wherever neccessary and redoing the damaged portion to the original condition after fixing etc. complete complying with standard specification and as directed by the deparmental officers. All Aluminium section shall be used in electrically controlled condition in accordance with IS1868/1962 for an average anodic film thickness of 15 microns etc., complete.

Wiringwith2x1.5sq.mm.PVCinsulatedsinglecoreunsheathedFRLScopperconductorcableof1100Vgradeinsuitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open PVC light point/fanpoint (forelectronic regulator)

Wiringwith2x1.5sq.mm.PVCinsulatedsinglecoreunsheathedFRLScopperconductorcableof1100VgradeinsuitableheavygaugeMSconduitpipeonwallandceilingwithMSaccessorieswith150mmx100mmx75mmMSswitchboxfor5A3pinnoninterlockingflushtypeCSplugwfthpaintingofsuitablecolourwithcontinuousearthwireconnection of 1.5 sq.mm copper wire for open plug point

Wiringwith2x4sq.mm.PVCinsulatedSCunsheathedFRLScoppercableconductorcableof1100VgradeinsuitableheavygaugeMSconduitpipeonwallandceilingwithMSaccessorieswith150mmx100mmx75mmMSswitchboxfor15A3pinnoninterlockingCSplugwithpaintingofsuitablecolourwithcontinuousearthwireconnectionby4sq.mmcopper wire for open power plug point

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supplyandfixingof4'40Wtwinboxtypefluorescentfitttingcompletewithcopperchokeandcondensorwithconduitpipe suspension from ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting with fluorescent Tubes

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Please Enable Macros to View BoQ information