PROVISION OF RADAR SECTION,TELECOMMUCATION SECTION, OPTO INSTRUMENT SECTION ,AND NETWORKING SUPPORT CENTER AT 972 LT AD MSL REGT (SP) WKSP IN THE AREA OF AGE B/R-II UNDER GE (EAST) DELHI CANTT-10

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil etc complete all as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out and getting out in soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation/under floor complete all as specified & directed.

M&L for RCC M-25 Design Mix (20mm graded aggregate) as in foundations footings, plinth beams etc all as specified & directed.

M&L for RCC M-25 Design Mix (20mm graded aggregate) as in columns, pillars etc all as specified & directed.

M&L for RCC M-25 Design Mix (20mm graded aggregate) as in beams, lintels etc all as specified & directed.

M&L for RCC M-25 Design Mix (20mm graded aggregate) as in chajjas etc all as specified & directed.

M&L for RCC M-25 Design Mix (20mm graded aggregate) as in slab type Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

S&F TMT bars upto 10mm dia and over, cut to length, bent to shape required,including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complet all as specified.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified

M&L Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes,cantilevers, shelves including supports, overhangs, etc also splays beteen floors and beams finished rough surfaces of concrete complete all as specified.

M&L Formwork to chajjas, chullah hoods, similar items including edges all as specified.

M&L brick work with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:4 all as specified and as directed.

M&L half brick wall with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:4 all as specified and as directed.

M&L hardcore of broken stone or boulders of gauge exc.63mm but n exc 100mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface.

M&L100 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base/floor complete all as specified and as directed.

Filling earth under floor spreading, leveling in layers n.exc 25cm thick well ramming including watering complete all as specified and directed by Engr-in-Charge.

M&L ATT the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete.

M&L ATT the soil along with external perimeter of building/along the perimeter at plinth level at the rate of 2.25 litre of emulsion per metre complete.

M&L for providing and fixing factory made UPVC white colour siliding window three track made xtruded profiles with all thickness of 2.3mm, having profile with hollow section with multi chamber. Frame size (60mm x 62mm), sash (42mmx67mm), sliding inter lock (one vertical length in each shutters) (45.5mmx28mm),glazing head (24.50mmx 16), mitered cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water etc. including EPDM gaskets 1.2, thick glavanised steel frame (30mmx21.50mm), sash (30mmx 18 mm) profile to be inserted in required profile frase will be fixed to the wall with 8mmx100mm long fasteners including hardware vz touch lock of zinc alloyed ( white powerder coated), steel roller system , aluminium track on bottom rail two track sliding frame wool pine for sliding sash and interlock complete. Note: The unit rate quoted by the contractor included cost of glass and SS wire mesh. Net openning will be measured for payment purpose.

S&f stainless Steel (S-304) work as in tubular pipe such in ,balluster, railing,Grill work etc fixed with suitable arrangement as required complete all as specified and as directed.

M&L for marble of any shade other than white and black 18- 20 mm thick ( table rubbed and polished ) in steps, Jambs,pillars, Cooking platform, floor and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble laid over and including 15mm thick screed bed in CM 1:6 , bedded, jointed and pointed with grey cement slurry including cutting and polishing complete all as specified and directed.

All as per srl item No 28 here-in-before but over rendering 15mm thick in CM 1:4.

M&L Granite of 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, window cills,cooking platforms,wash basin counter and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade laid over and including 15mm thick screed bed in cement mortar (1:6) polishing bevelled edges of corner,moulding etc complete all as specified and directed.

M&L for Preparation of new plastered surfaces of walls and two coats of exterior emulsion paint over a coat of priming paint incl 2 mm thick wall care putty etc complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of plastic emulsion paint over a coat of priming coat including wall care putty on newly plastered walls of 2-3mm thick wall care putty incl removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying two coat of plastic emulsion paint over a coat of priming coat including wall care putty on newly plastered walls of 2-3mm thick wall care putty incl removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder complete all as specified and directed.

M&L Providing and applying high quality acrylic modified resin based texture of finetex Honeycomb sand stone- 3211with anti alage and UV resistance property to be applied as in intermeadite finishes in desired pattern @ 43.04 kg/10 sqm to form film of 1 - 1.50 mm thickness after scrapping and properly cleaning the surfaces to remove loose particles from the plaster surfaces and applying coating with premium acrylic smooth exterior paints with Silicone additives of required shade by two or more coat @ 1.43 Ltrs/ 10 sqm over and including one coat of premium quatity primer complete all as specified and as directed by Engr- in-charge.

M&L for Vitrified tiles(Double charge) light Shade 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 Sqm but not exceeding 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete.

All as per serial item no 35 above but on vetical surfaces like Jambs,Pillar ,Riser etc 10 mm rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including backing coat of 10mm thick CM 1:4 on brick masonry/concrete surfaces finished even to receive tiles complete.

M&L Coloured Glaze ceramic tiles 300x600 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete.

M&L Providing and fixing false ceiling at all height with GRG(Glass Fibre Reinforced Gypsum) False ceiling tiles of size 595x595mm of approved texture design and patterns having moisture content less than 2%,humadity resistance of 99%,NRC 0.85(with 50mm thick glass wool) as per IS 8225 :1987,Non combustible as per BS 476 (part-4)-1970 and light reflectance of 75-85% to be laid in true horizantal level suspended on inter locking metalT-grid of hot dopped galvanised iron section of 0.3 mm thick (galvanised@120grams per sqm including both sides) comprising of main -T runners of size 24x32 mm of length 3000mm.cross-T of size 24x26mm of length 1200mm and secondary intermediate cross T of size 24x26 mm of length 600mm to form grid module of size 600x600mm,suspended from ceiling using galvanised mild steel items(galvanised@80 grams per sqm) i.e 50mm long,8mm outer diameter M-6 dash fasteners,6mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2mm galvanised iron perimeter wall angle of size 24x24x0.4 mm of length 3000 mm to be fixed on periphery wall/partition with the help of plastic rawl pluges at 450mm centre to centre and 40 mm long dry wall stainless steel screws, complete all as specified and as directed.

S&F fancy type Curtain rods decorative type stainless steel 25mm nominal dia and 3 mm thickness of approved quality (Make VISTA) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods complete all as directed and specified.

M&L 10 -12mm thick polymer modified readymix cement base plaster as per manufacturer instruction on fair / unfair faces of brick work or concrete surfaces & finishing the surface even & smooth as per manufacturer instruction complete all as specified & directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

M & L PVC bend 110mm bore any radius complete all as specified and directed by Engineer- In- charge.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in roof levelling complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer of cement mortar 1:4 on brick work or concrete surfaces using water proofing compound, from 1st to 4th floor including necessary scaffolding and safety, complete all as specified and directed

Supply only liquid water proofing compound.

M & L for priming over roof surface @ 0.25 Ltr/Sqm over a cleaned roof surface and applying one coat of bitumin painting with hot blown grade bitumin 85x25 @ 1.20Kg/ Sqmtr and laying of APP based polymetric membrane minium weight 3kg/ sqm and minium 3mm thick reinforced with polyster non wove febric ( wt not less than 150gms/ sqm) land on primed surface by forced application and applying two coat of solar reflective aluminium paint on duly prepared surface of membrane complete all as specified and directed. (Note : (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Ten years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M&L Providing cement concrete type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, hold fast, rounded or cmamfered on edges, water trought and the like including weathering slightly rounded and threating as directed complete.

M & L 75 mm thick PCC 1:3:6 type C-1 using 20 mm graded aggregate as in floor/Plinth protection finished surface even and smooth using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for precast machine pressed cement concrete tile size 250x250x20-25 mm or 300x300x20-25 mm thick confirming to IS:1237 laid over & including 15 mm thick screed bed or bedding layer of cement mortar 1:4 and jointed & pointed with CM 1:4 complete all as specited and directed

M&L 75 mm thick Plain cement concrete (1:4:8) Type D-2 using 12.5mm graded stone aggregate as in floors and finished the surface fair to received screed bed all as specified and directed even and smooth without using extra cement

M&L Sand filling under floors or in foundations including watering and consolidations complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size with modular sheet for fixing modular switches/ sockets/ fan regulator etc , complete all as directed

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

All as per srl item No. 53 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp light point.

S & F Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S & F Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.

S & F modular socket two-in-one, 6 Amp universal type, 02 module size complete all as directed.

S & F modular Socket, 16 Amp, multipurpose shutter type, 02 module size complete all as directed.

S & F Modular Fan regulator step type ,120 watts complete all as directed.

Supply and fixing ceiling fan complete with blades, down rods,suitable for regulator and accessories, 230 V, 1200mm sweep (BLDC) complete all as directed.

Supply and fixing Ceiling rose, insulated body, 3 terminal, 230 volts, 5 Amps complete all as directed.

Supply and fixing LED tube light fitting, 20 watt ,230V wall mounting type and including all electric connections complete all as directed.

M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

Material and labour SPN DB with double door 12 way, 240V with busbar 200A rated,making all electric connections complete all as specified and directed.

S&F of MCB, single pole, 6 to 32Amp, C curve type 10 KA, 240 Volt. making all electric connections complete all as specified and directed.

Supply and fixing MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed.

S&F MCCB 3P 125 Amp with breaking capacity 16 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified.

S&F MCB, SPN, 40 TO 63 Amp, C curve type 10 KA, 240 Volt. complete all as specified and directed.

Material and labour laying of LT underground cable XLPE insulated, PVC sheathed, galvanised steel strip / wire armoured, aluminium conductor, 1100 volts grade, of size 35 Sqmm 4 core suitable for earthed system laid in duct / trench / along pole / wall etc including making connection complete all as directed.

M&L for sand cushioning to under ground cable provided with layers of sand(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixing in street light fitting bracket, 1mtr long made out of galvanized iron pipe of 25mm dia size light grade complete with nut, bolts, complete all as directed.

Supply and install hi wall split units 1.5 TR indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma fitter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity. (Make : HITACHI/ VOLTAS/ CARRIER/ DAIKIN/ BLUE STAR)

Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stablized at 230 V with accuracy of plus or minus 2.5% and of capacity 4.0 KVA.

M&L Sub main wiring with 2 run of 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to Sub main DB complete all as specified.

Supply and fixing of Modular AC socket with 25 Amps SP mini MCB, 230 Volts, 50 Hz, in 4 module sheet metal enclosure complete all as specified and as directed by Engr-in-Charge.

Prabhu Infrastructure And Developers

M/s Durga Traders

J S CONSTRUCTION CO

TRADCO ENTPRISES