SPECIAL REPAIRS TO BLDG NO P 48 AT POST OFFICE COMPLEX UNDER GE NORTH BANGALORE

Amount

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof covering etc complete all as specified and as directed

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in Framed work etc complete all as specified and as directed

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitions etc complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed

Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

All as per item No 10 above but for 20 mm dia bore

All as per item No 10 above but for 25 mm dia bore

Taking down cement plaster of any description hacking for key or raking out joint on old brick work/stone/concrete surface etc complete all as specified and as directed

Dismantling of cast iron or reinforced concrete drain pipe up to 150 mm dia incl fittings, jointed in cement mortar and taking out trenches if reqired etc complete all as specified and directed

Dismantling water tanks exc 500ltr but not exc 1000 ltr and removing to store etc complete all as specified and as directed

M&L MS Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc including box section etc complete all as specified and as directed

S&F MS Hollow /Solid steel section for structural use in beams, col, rafter purlins or other connecting plates incl necessary welding, riveting, nut bolts as per IS-4923 etc complete all as specified and as directed

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and as directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding ridges under valley to wall, fixed with self tapping screws etc complete all as specified and as directed

M&L for 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded stone aggregate) as in sub base of flooing etc complete all as specified and as directed

M&L for cement concrete type B-0 1:2:4 (12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed

M&L for screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as dado/skirting etc complete all as specified and as directed

All as per item No. 23 above but for Non skid tiles in skirting

M&L Glazed ceramic coloured tiles 300X450X7mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

M&L 18 to 20 mm thick Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including grinding the edges half round and polishing including etc complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed

All as per item No 29 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed

M&L Pre-cast Cement concrete Type 1:3:6 using (20 mm graded stone aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:6 all as specified and directed.

M&L for Providing precast cement concrete Type B-1 1:2:4 (20 mm graded stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:6 etc complete etc complete all as specified and as directed

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surfaces of concrete complete all as specified and directed.

M&L RCC (Nominal mix) type A-1, 1:1.5:3 (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in hold fast and filling of pressed steel chowkhat etc complete all as specified and as directed

M&L MS framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290-0 or Fe -E-165 etc complete all as specified and as directed

S&F 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed

S&F factory made 2nd class HW 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitered beads for securing glass,\etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and as directed

S&F in repairs 18/19mm thick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in cub board shutter, shelves etc complete all as specified and as directed

M&L for 0.90 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions, fixed to door/cub board shutter incl teak wood beading 3mm thick and 18 mm wide incl painting to match the existing colour etc complete all as specified and as directed

S & F for solid PVC frame (Single Rebated) of size 50 mm x 47 mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete as sepecified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face etc. complete all as specified and as directed.

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified and as directed

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed / Sliding type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete shall as specified and as directed

S&F 4mm thick sheet glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in squares n exc 0.50 sqm in each pane complete all as specified and as directed

S&F 4mm thick sheet Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane etcc omplete all as specified and as directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple etc complete all as secified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 100 mm thick butt hinges, heavy weight, stainless steel and fixed etc complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed

S&F in repairs stainless steel curtain rod of 25 mm bore (weight not less 400 gms per running meter) incl fancy finale caps cap etc complete all as specified and as directed

S&F in repair stainless steel Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed

S&F in repairs EWC (Ivory) with normal closing seat cover of size 540X375X415mm with S Trap incl connection to out going pipe, & seat cover and flushing pipe complete all as specified and as directed (Make Cat no 4018 of Prayag of equivalent make of CA)

S&F in repair white vitreous china wash basin Ivory flat back size 550x400 excluding taps but including 32 mm dia chromium plated aste fitting, PVC waste pipe 610 mm long and PVC connection 450 mm long complete all as specified and as directed (Make Cat no 4645 of Prayag of equivalent make of CA)

S&F in repairs PVC flushing cistern valveless with flushing out vavle flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets & connection to pipe etc incl PVC connection 450 mm long complete all as specified and as directed (Make Cat no-502 of Prayag of equivalent make of CA)

S&F in repairs bib cock long body with flange fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed (Make Cat no 9208 of Prayag of equivalent make of CA)

S&F in repair 15mm bore Brass CP wall mixer with L Bend (with provision of hand shower) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed (Make Cat no 9275 of Prayag of equivalent make of CA)

S & F in repairs 15 mm bore central holes mixer w/o pop up waste system (9" spout) all as specified and as directed. (Make Cat no 9350 of Prayag of equivalent make of CA)

S&F in repairs angle cock with flange fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch fixed for 15 mm dia bore pipe complete all as specified and as directed (Make Cat no 9210 of Prayag of equivalent make of CA)

S&F PVC water connection 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

S&F in repair full corner Glass Shelf (with brass brackets) etc complete all as specified and as directed (Make Cat no BEA-52 of Prayag of equivalent make of CA)

S&F in repairs soap dish holder with glass etc complete all as specified and as directed (Make Cat no BA-25G of Prayag of equivalent make of CA)

S&F in repairs overhead round rain shower 8" Iwith out armns) of 15 mm bore dia etc complete all as specified and as directed (Make Cat no BOS-41 of Prayag of equivalent make of CA)

S&F in repairs Hand shower (Health faucet) (ABS Body) with 8 mm dia, 1.20 mtr long flexible tube & wall hook etc complete all as specified and as directed of Prayag or its equivalent make of CA)

S&F in repairs Jet spray suitable for EWC / Ango Indian EWC including fitting etc complete all as specified and as directed Prayag of equivalent make of CA)

S&F in repairs Stainless steel plate rack of size 990.60mm x 914.40mm including fixing to wall as directed etc complete all as specified and as directed

S&F in repairs SS Towel rail 450 mm long incl fixing arrangement etc complete all as specified and as directed (Make Cat no GM-04 of Prayag of equivalent make of CA)

S & F 16mm dia CPVC pipes SDR 11 & Plain CI'VC SDR 11 fittings on walls/ ceiling or laying in floors incl cutting holes for concealing the pipes in stone / brick masonry complete all as specified.

All as per item No 74 above but 20 mm dia of bore pipe

All as per item No 74 above, but 25 mm dia of bore pipe

S&F in repairs rotational moulded PVC water storage tank 1000ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and as directed

S & F 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed [Minimum weight for 20 mm – 210 gms] .

S & F in repairs 25 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed.

S&F 110mm PVC, SWR pipes type 'B', single socketed in any length with rubber ring joint leaid in trenches or in floor complete all as specified and directed

All as per item No. 80 above but 75mm bore pipe complete all as specified and directed

S&F 110mm PVC, SWR pipes type 'B', single socketed in any length with rubber rings joint fixed with wall complete all as specified and directed

S&F PVC bends (any radius) of 110mm dia.

S&F PVC bends (any radius) of 75mm dia.

S&F PVC vent cowls of 110mm dia.

S&F in repairs 75 mm dia bore PVC (SWR) multi floor trap with grating including jointing with solvent cement etc complete all as specified and as directed

S&F in repairs for Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

Supply only water proofing compound (Liquid) complete all as specified and as directed.

M&L for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed

M&L for Preparing new plastered suface of walls and applying two coats distemper oil emulsion, white or tinted over a coat of primer etc complete all as specified and as directed

Material & Labour for praparing new plastered surfaceof wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (Apex Ultima) of required shade (Company Depot Tinted) with silicon additives coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

S&F in repairs GI False ceiling with grid suspended system of size 600X600mm standard section consisting of main runner 29 x 24.70 x 0.80mm, cross Tee 29 x 24.70 x 0.80mm and wall angle 22.2 x 22.2 x 0.65, ceiling suspended with 3 mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main corner, cross tee& wall angle of MS galvanized with PPPCGS) incl 4 mm thick HPSC self textured design pre primered non asbestons fibre cement building boards fixed to false ceiling etc complete all as specified and as directed

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. incl 15 mm thk screed bed in CM 1:6 complete all as specifed and as directed

M&L for 75 mm thick PCC 1:3:6, type C-1, using 20 mm graded stone aggregate as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade "A" complete all as specified and directed.

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches ceiling roses, regulators, sockets, fans etc and making good the disturbed surface of walls, ceiling etc incl painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

Point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit incl accessories concealed type of wiring run on walls incl MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. One light / fan point controlled by one switch

All as per item No. 101 above but for One 3 pin socket out let 5 Amps on independent board

All as per item No. 101 above but for One 3 pin socket out let 5 A on same board

All as per item No. 101 above but for One Bell / Buzzer Point controlled by bell push

Point wiring complete with 2.5 Sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit incl accessories concealed type of wiring run on walls incl MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. Note for Item No 101 to 105:- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring. (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring. (v) Cost of cutting chases for conduits and making good to walls, in case of recessed or concealed conduit wiring will be included in point wiring.

S&F LED batten suitable for indoor applications 20 Watts, 4 feet with extruded aluminium housing & integrated LED channel complete with all accessories including taking out old fittings all as specified and directed. Make: Bajaj, Cat No. BCLAB 20 W LED P S or equivalent Makes & model in Havells/Phillips/CG

S&F LED batten suitable for indoor applications 10 Watts, 2 feet with extruded aluminium housing & integrated LED channel complete with all accessories including taking out old fittings all as specified and directed. Make: Bajaj, Cat No. BCLSB 10 W WH or equivalent Makes & model in Havells/Phillips/CG

S&F Decorative, wall mounting ,champagne gold finish fixture with plastic body suitable for 9 watt LED lamp B22 base all as specified and directed by Engineer -in-Charge.

S&F switch piano flush type single pole one way 5amps

S&F of Ding Dong bell AC 230 volts single pole.

S&F of bell push flush type 5A all as specified and as directed .

S&F of stepped type electronic fan regulator flush Switch / socket type all as specified and as directed

S&F of Switch socket combination 2 in 1 , 5 Amps flush type all as specified and as directed

S&F of switch socket combination 2 in 1, 3 pin 5 and 15 Amps flush type universal all as specified and as directed

S&F in repairs of MCB SPN 240 volts 32/40 Amps complete all as specified and as directed

S&F in repairs of MCB single pole 240 volts 10/16/20/32 Amps complete all as specified and as directed

S&F in repairs of MCB DB SPN 12 way double door type 240 volts with 200 Amps rated busbar as specified and as directed.

S&F Storage type water heater 25 Ltrs BEE 5 star rated complete incl steel wired pipe for hot/cold water connection for inlet and out let water etc complete all as specified and directed at site .

S&F in repairs of MCB DB TPN 4 way double door type 240 volts with 200 Amps rated busbar as specified and as directed.

S&F in repairs of MCB TPN 415 volts 10 KA 'C' 63 Amps complete all as specified and as directed

Excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables/errection of pole etc complete all as specified and as directed.

Returning, filling in trenches incl spreading leveling watering and well ramming in layers with hard/dense soil not exc 25 cm thick in each layer complete as specified and as directed

Removing excavated soil to a distance not exc 1.5 mtr above the starting point complete all as specified and as directed

M & L for sand cushioning with a layer of M-sand under and above the cable complete all as specified and as directed. Note: Punned thickness will be measured for payment

S&L bricks for cable protection complete as specified as directed

S&L cable XLPE insulated screened PVC bedded galvanised steel strip or wire armored,electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor connected with suitable legs including taking out the existing unserviceable cable for following size 4 C x 25 Sqmm

S&F in repairs of ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed

Removing of old unsv submain wiring and provision of new sub main wiring 1100 volts grade multistranded FRLS copper conductors with, two runs of single core 6 Sqmm along with 6 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with suitable non metallic rigid PVC concealed conduit all as specified and as directed. Note: 3 runs of cable and one run of PVC conduit will be measured as unit length. Note:- Cost of cutting chases on wall / floors etc and making good disturbed surface is deemed to be included in unit rate quoted by contractor.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion incl earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cost slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways incl funnel with watering pipe wire mesh and lugs, incl test point complete all as specified and as directed including dismantling and taking out old u/s earthing.

Supply and fixing 30 W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection including taking out old fittings. Make:- Bajaj, Cat No.:- ENXT P 30L WH PO PC SD MT or Equivalent Makes & model as per CA.

S&F GI Bracket made out of GI tubing medium grade 25 mm bore , approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from bldg complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete including necessary core cutting arrangement for installation all as specified and directed Make:- Bajaj, Model- Bahar or its equivalent as per CA including provn of neccessary core cutting of required size and making good of disturbed surface of wall and cost of the same is included in unit rate quoted.

S&F in replacement PVC Fresh air fan of 200/225mm sweep 1200/1400 RPM with louver complete including necessary core cutting arrangement for installation all as specified and directed. Make:- Bajaj, Model- Maxima DXL-G02 or its equivalent as per CA including provn of neccessary core cutting of required size and making good of disturbed surface of wall and cost of the same is included in unit rate quoted

Sangam Construction (BID ID -3278473)

M/S POTHIRAJ AND CO (BID ID -3278680)

B5BUILDING SOLUTIONS (BID ID -3275097)

S S CONSTRUCTIONS (BID ID -3274932)

M/S SIRI BUILDERS (BID ID -3277765)