Carrying out Street light and Assembly hangar lighting works at ARDC

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, etc.,

Address for correspondence:

Bank(s) details: [Copy of the cheque leaf to be uploaded]

Related Document to be Uploaded to eProcurement Portal (Note Cancelled cheque leaf to be uploaded)

PAN No.:

Average annual financial turn over during the last 3 years, ending 31st March of the previous financial year [ should not be less than 30% of Amount put to tender]

TURN OVER IN Rs:

Please Enter Turn over in Rupees for all the 3 years

Details of Registered Contractor

ESI No.:

GST Detail:

Please Enter GST Details

Related Document to be uploaded in ePortal

Contact details

Please Enter Contact person Name

Please Enter Mobile No

Valid Electrical contractor license of appropriate voltage (Minimum 650V) issued by any state Govt. under clause 45 of Indian Electricity Rules 1956 or as amended from time to time

Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued within a period 12 months from the final date of submission of tender.

Please Enter Details to 'Name of the Bank' , 'Date of Issue','Value in C89``Rs. in Lakhs

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender should be either of the following: [Work completion certificates along with LOA/PO/WO should be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated amount put to tender. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated amount put to tender. (iii) ONE similar completed work costing not less than the amount equal to 80% of the estimated amount put to tender.

Type of Work: [Incase of private works the same shall be supported with TDS certificate]

Type of Work: [Incase of private works the same shall be supported with TDS certificate]

Please Enter Details for Work No II

work done

Type of Work: [Incase of private works the same shall be supported with TDS certificate]

Please Enter Details for Work No III

Details of person holding the power of Attorney :

Related Document to be Uploaded to eProcurement Portal

Please Enter Details for Person holding Power of Attorney

DECLARATION I

Please Accept the Declaration I

DECLARATION II

Please Accept the Declaration II

Subject tender has been called on item rate basis. Basic Rate to be quoted for each item.

Subject work is a Works contract and prevailing GST of 18% has been added in the BOQ on overall total. Any revision on this GST rate is to HAL account.

Sucessful offer that is L-1 (Lowest offer) will be determined including GST.

The payment terms shall be governed as per the terms indicated in General conditions of contract.

Amount towards GST will be paid along with RAR payment against invoice.

The tenderers are requested to abide by the rules of prevailing GST act.

This BOQ specification has to be read in conjunction with technical specifications and tender drawings. Any ambiguty in these have to be brought to the knowledge of contract section before submission of tender to avoid future claims/dispute.

Specification of item

Supply, fixing of single arm bracket of 1500mm length of 40MM dia B-class GI Pipe on existing street light Pole at a height of more than 7 meters including necessary clamps and fastners complete in all respects.

Supplying of 4Cx16 Sqmm PVC/XLPE, insulated Aluminium conductor 1.1KV gr. Armoured U.G cables in required lengths complete in all respect as directed by EIC and as per technical specification.

Laying in the excavated cable trench/fixing on wall/duct wall with necessary M.S clamps / encasing in pipes etc., testing & commissioning of XLPE armoured Aluminium power cable of 1.1 KV grade of 4C x 16 Sqmm. size in required lengths including necessary excavation in soil, sand cushioning, protective covering with well burnt bricks and refilling the trench etc as per technical specifications complete in all respects.

Supply and making end termination for 4Cx16 Sqmm PVC/XLPE, insulated Aluminium conductor 1.1KV gr. Armoured U.G cables with brass compression glands and aluminum lugs complete in all respects.

Supplying and installingcable route marker made with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) of size 600mm x 600mm at the bottom and 500mm x 500mm at the top with a thickness of 100mm including necessary inscription engraved as directed by EIC.

Concrete Work

Concrete cutting/Chipping the existing 1:2:4 cement concrete road /pavements/Bitumen Road / flooring of 150mm thick including removing debris from the work site as directed by the Engineer-in-charge.

Re-concreting the cut portion with 1:2:4 cement concrete by employing 20mm graded aggregate granite, smooth finish including curing, complete in all respects and as directed.

Supply & fixing of following LED Street light fittings.

Supply, fixing on existing street light pole using suitable fixing hardwares and testing & commissioning of Street light LED light fixture of wattage not exceeding 70watts and lumens output not less than 8400lumens with necessary interconnections consisting of pressure die cast aluminum housing with powder coated paint, optical lenses suitable for heat resistance polycarbonate/ PMMA with IP66, operating on single phase 230V 50Hz AC supply, efficient heat sink, colour temperature shall be 5700K+5%, suitable optics for maximizing the spread complete in all respects and as directed by engineer-in-chage. The luminaire shall have specific lens for optical dispersion including control gear and power factor of control gear shall be >0.9. The fitting shall have internal surge protection of 4KV and external surge protection of 10KV. LM 79 certification for luminare & LM80 certificate for LED shall be produced. LED used in the luminaire should be one of approved make as per approved make list of HAL. Make/model of Street light LED fixture: Bajaj ENXO 84L WH PO PC SD or Equivalent model of other approved makes.

Supply, fixing on existing street light pole using suitable fixing hardwares and testing & commissioning of Street light LED light fixture of wattage not exceeding 30watts and lumens output not less than 600lumens with necessary interconnections consisting of pressure die cast aluminum housing with powder coated paint, optical lenses suitable for heat resistance polycarbonate/ PMMA with IP66, operating on single phase 230V 50Hz AC supply, efficient heat sink, colour temperature shall be 5700K+5%, suitable optics for maximizing the spread complete in all respects and as directed by engineer-in-chage. The luminaire shall have specific lens for optical dispersion including control gear and power factor of control gear shall be >0.9. The fitting shall have internal surge protection of 4KV and external surge protection of 10KV. LM 79 certification for luminare & LM80 certificate for LED shall be produced. LED used in the luminaire should be one of approved make as per approved make list of HAL. Make/model of Street light LED fixture: Bajaj ENXO 36L WH PO PC SD or Equivalent model of other approved makes.

Supply and fixing on the street light pole using suitable angle iron frame work, fixing hardware, suitable size weather proof SMC box(not less then 250x200x105mm) with hinged lockable cover and providing 25A 6way heavy duty PVC connector inside the SMC box, with suitable knockouts for cable entry & exit as directed by Engineer -in-charge.

Supply & drawing/laying of 3Cx2.5 sqmm 1100V gr. PVC insulated unarmoured copper Cable and connecting from connector using necessary lugs, upto the light fixture complete in all respects. (for connecting street light fixtures & High bay light fittings from connector box)

Supplying & fixing of 25MM size of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and laying of 63mm dia, PE-100, PN8 ISI marked HDPE pipe confirming to IS 4984:19955 including suitable jointing using welding as required in the excavated trench/duct/at road crossings for encasing cables complete in all respect as directed by Engineer-in-charge.

Supply, fixing to/suspending from existing MS perlins/ ceiling at approx. 10-12 mtr height, using suitable MS angle frame work with required fixing hardwares etc., as per site requirement, testing & commissioning of industrial type highbay LED lighting fixture of wattage not exceeding 150watts made out of high pressure diecast aluminium housing, diffuser made of high grade toughened glass, integral control gear, eye hook etc., (as per OEM standards). The technical parameters of lighting fixtures are as below: The luminaire should have Lumen efficacy ≥ 125lm/watt and lumen output not less than 18750lumens, PF>0.90 and Colour temprature shall be ≥5700K, THD <10%, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting fixtures and other standard accessories complete in all respects and as directed by Engineer in-charge. The fitting shall be of Crompton model no: LHB11-150-CDL/60-HPM/ Equivalent model in other approved makes. LED used in the lighting fixtures should be one of the approved make. LM79 certification for luminares & LM80 certificate for LED shall be produced. Note:-(i) The scope includes supply and fixing on MS perlins/ceiling, using fixing hardware, Cable junction/connector boxes IP 65/66 with integrated membranes for cable entry of Hensel make (not less then 130x130x77mm) or equivalent model in Legrand/ Hager/ Schneider with cover and providing 16A 6way PVC connector inside the box including terminating the existing wiring in the connector box. (ii)MS angle supports will be measured separately.

Design, Fabrication, Supply and fixing/grouting / welding to the existing MS perlins of suitable size MS angle iron supports/ flat/ brackets for fixing High bay light fittings, as per site requirement and painting the same with two coats of synthetic enamel paint over a coat of zinc chromite primer complete in all respects and as directed by EIC/OIC.

Dismanteling