REPAIR/REPLACEMENT OF ROOF TOP SHEET AND FALSE CEILING PAINTING OF 02 NOS AND 01 NOS SEMI PERMANENT BARRACK OF CWS II AND REPAIR MAINTENANCE OF ROOF TOP SHEET AND PAINTING OF RECREATION CLUB

Amount

Dismantling roofing including ridges, hips, valleys and gutters etc., andstacking the material within 50 metres lead of: G.S. Sheet

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed. using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side)inclusive) as per IS : 277 and consisting of angle cleats of size 25 mmwide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part 1) :2011 (Board with BIS certification marks)

9.95 Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 100x75x4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.: Twin rubber stopper

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, toachieve even shade and colour. Two coats

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with ecessary screws bolts, nut and washers etc. complete.

25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s pecification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places. for toilet and bathroom door

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand ndmanufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats Old work (one or more coats) sqm 62.70

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Dismantling roofing including ridges, hips, valleys and gutters etc., andstacking the material within 50 metres lead of:1 Asbestos Cement sheet

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to S:8931. 15 mm nominal bore

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Supply and Drawing following size of FRLS PVC insulatd Copper conductor single core cable in the existing surface/recessed steel/PVC conduit as required. : 3x1.5 sq mm

Supply and Drawing following size of FRLS PVC insulatd Copper conductor single core cable in the existing surface/recessed steel/PVC conduit as required. : 3x2.5 sq mm

Supply and Drawing following size of FRLS PVC insulatd Copper conductor single core cable in the existing surface/recessed steel/PVC conduit as required. : 3x4 sq mm

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. : 100 mm X 100 mm X 60 mm deep

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. : 200 mm X 150 mm X 100 mm deep

Supplying and fixing following modular switch/ socket on existing modular plate & switch box including connections but excluding modular plate etc. as required. : 5/6 A switch

Supplying and fixing following modular switch/ socket on existing modular plate & switch box including connections but excluding modular plate etc. as required. : 15/16 A switch

Supplying and fixing following modular switch/ socket on existing modular plate & switch box including connections but excluding modular plate etc. as required. : 3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on existing modular plate & switch box including connections but excluding modular plate etc. as required. : 6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( But without MCB / RCCB/ Isolator). : 4 way (2 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required. 8 way (4 + 24), Double door

Supplying and fixing of LED tube light including connections etc. as required. : 20 Watts

Supplying and fixing of LED tube light including connections etc. as required. : 10 Watts

Supply, Installation, Testing and Commissioning of 1200 mm sweep, , ceiling fan , 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, copper winding, , 350 RPM ,safety pin, nut bolts, washers,, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. Completed as required.

Komere Manoj Kumar (BID ID -3273511)