Renovation and modification of Seminar Hall in academic area at IIT Delhi.

1) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1.1) 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

2) Centering and shuttering including strutting, propping etc. and removal of form for :

2.1) Edges of slabs and breaks in floors and walls (For shuttering of steps water proof ply will be used and joint will be make water tight by filling POP or rubber gaskat to get expose finish and nothing extra shall be payble on account of this)

2.1.1 ) Under 20 cm wide

3) Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

3.1) All works upto plinth level (Top surface of RMC will be finished with cement sand mortal 1:2 (1 cement : 2 sand) with floating coat of neat cement when concrete is green and nothing extra shall be payble on account of this).

4) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

4.1) Cement mortar 1:4 (1 cement : 4 coarse sand)

5) Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

5.1) (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.

5.1.1) (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

5.1.1.1) (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

6) Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

6.1) Rectangular or square

7) Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

8) Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

9) Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

10) Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

11) Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-inCharge.

12) 12 mm cement plaster of mix

12.1) 1:4 (1 cement: 4 fine sand)

13) 15 mm cement plaster on the rough side of single or half brick wall of mix :

13.1) 1:4 (1 cement: 4 fine sand)

14) Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

14.1) Two or more coats on new work

15) Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

15.1) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

16) Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

17) Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge

17.1) With cement mortar 1:4 (1 cement : 4 fine sand)

18) Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

19) Melamine polishing on wood work (one or more coat).

20) Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

20.1) Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

21) Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

22) Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge

22.1) In cement mortar

23) Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

23.1) Of area 3 sq. metres and below

24) Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

24.1) Of sectional area 40 square centimetres and above

25) Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

25.1) Thickness above 10 mm up to 25 mm

26) Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

27) Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

28) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

28.1) For fixed portion

28.1.1) Powder coated aluminium (minimum thickness of powder coating 50 micron)

29) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

29.1) Powder coated aluminium (minimum thickness of powder coating 50 micron)

30) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

30.1) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

31) Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

31.1) With stainless steel cover plate minimum 1.25 mm thickness

32) Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

33) Supplying and placing in position auditorium chair of Godrej Make Model MARS WITH DESKLET with following specifications. The armrest- is made up of integral skin polyurethane foam with 65+/- 10 shore A hardness and reinforced with wooded insert. The armrest is fitted with sidepanel through an concealed zinc plated hinge. Foam- Foam is HR Polyurethane foam with density = 45+/-kg/m3. Seat Assembly- The seat assembly is made of polyurethane foam moulded with M.S. tubular frame insert which is upholstered with fabric. The insert is tubular made of 1.9 +/-0.02cmX 0.16 +/- 0.013cm thk MS ERW round tube with flexible support straps running across the length and width of the frame. The seat has an auto – tipup feature making it stay in upright position when not in use enabling clear row passage ( Approx. seat size: 45.5 cm ( W) X 46.5 cm(D)).

33) Backrest Assembly: The back assembly has a flexi back mechanism. It is made of polyurethane foam moulded with M.S tubular frame insert upholstered with fabric and has a plastic back cover. The insert is a tubular frame made of 1.9+/-0.02 cm X 0.16+/- 0.013 cm thk M.S ERW round tube with flexible support straps running across the length & width of the frame. Back size- 45.5cm (W) X 70.4cm (H). Retractable Desklet- The desklet is made of 1.8+/-0.05 thkprelaminated particleboard with-in-situ injection moulded polypropylene edge all around. Desklet top is mounted on high pressure die-cast aluminum arm through metal bracket 0.2+/- 0.05cm thk H.R Steel. The assembly is mounted on side panel through desklet arm connector made up of glass filled nylon. Desklet dimension 27+/-0.1 cm (W)X 32.0+/-0.1cm (D) Power Coating- Steel Components are epoxy polyester coated (DFT 40 to 60 microns) Note- In this estimates, Godrej interio’s ‘’ MARS model with Desklet’’ for auditorium chair has been considered. In case of other makes, technical specifications should be equivalent and cost adjustment shall also be done if the equivalent make is of lesser market price than Godrej intero Mars with desklet.

34) Providing wall panelling of approved make as per specification and direction of EIC at all heights and levels.

34.1) Providing and Fixing Channeled Woodworks perforated panels of Armstrong Industries / Saint Gobain or approved equivalent make of width 192mm, thickness 15mm and length 2400mm or as required by the Engineer-in-Charge, made of a medium density particle board substrate with a laminated facing as per the approved shade/ species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a (“Helmholtz” fluted perforation of 3mm width and 21mm visible panel) each. The panels shall provide a minimum sag resistance of RH90 and a fire rating class of 1 as per Part 7 of BS 476. The edges of the panels shall be “tongue-andgrooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece with NRC > 0.5. The panels shall be mounted on special aluminium splines using clips as approved by the Engineer-in-Charge

34.1.1) Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre-to-centre. Screw the aluminium extruded keel for channelled woodworks provided by Armstrong over the lowest and second wooden batten at an on-centre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation team & Installation should be carried out as per manufacturer recommended procedure. (Make- Armstrong, Anutone, Credence, Topakustic)

35) Providing and fixing 2 mm thick homogeneous polyvinile chlorifde sheet / tile in flooring and skirting in approved pattern on a smooth and damp proof base using rubber based adhesive of ( approved quality and manufacturer like fevicol Sr 998 or equivalent including rolling with light wooden roller weighing about 5 kg. all complete as directed by Engineer-in-charge. approved colour and shade. ( Armstrong / Polyflor./ Tarkett

36) Providing and applying acrylic aggregate textured wall coating in pigmented finish ( Spectra Plast 1053 - of soectrum paints / Rustic texture paints of Dulex / Rustic texture paints of Burger ) maintaining material consumption rate of average 3.0 to 3.5 Kg. per Sqm. and upto 2 mm. average thickness on new walls in the exterior / interiors of the building. Undulations, broken edges, minor imperfections / irregularities should be rectified by using a paste made of Spectrum Rectochem Surface Improver mixed with ordinary portland cement in the ratio of 1:1. Old, flaking, plaster of paris, gypsum and highly absorbent surfaces and those already finished with lime or distemper should be brushed down and then treated with a coat of Spectrum Prime Coat or equvalent diluted with water as per the rcomandation of manufacturer applied by a brush.

37) Providing and fixing 12 mm frame less toughened glass of approved brand and manufacturer in railings fixed to RCC member with the help of 4 mm thick, 265 mm high M.S. chanel and other fittings and fixtures as per architectural drawing and instruction of Engineer in Charge all complete. (Rate shall be inclusive M.S. chanel and all other fittings/fixtures).

38) Providing and fixing factory made hot pressed both side laminated flush door ready made shutter with one mm thick decorative laminate on both side confirming to IS:2202 (Part-I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grain or cross bands and face veneer on both face of shutters.

38.1) 35mm thick including ISI marked stainless steel butt hinges with necessary screws.

39) Dismantling old damaged PVC flooring work including stacking material within 50 metres lead. For any thickness.

Electrical Work

40) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

40.1) Group C

41) Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor 40.3single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

42) Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

42.1) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

42.2) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

42.3) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

42.4) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

43) Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

43.1) 15/16 amp switch

43.2) 6 pin 15/16 amp socket outlet

44) Supplying and fixing following size/ modules, GI/PVC box alongwith modular base & cover plate for modular switches in recess etc as required.

44.1) 3 Module (100mmX75mm)

44.2) 6 Module (200mmX75mm)

44.3) 12 Module (200mmX150mm)

45) Supplying and installation of Surface mounting LED luminaire equipped with CRCA powder coating housing, anti glare polycarbonate diffuser with energy efficient electronic driver with following features:- Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 34 Watts;Output lumens not less than 3300 lm; CCT 4000K; Dimension in mm (600X600); Nominal surge protection 2.5 kV;Power factor not less than 0.9; Minimum IP protection 20;

46) Supplying and installation of Surface mounting round LED luminaire equipped with extruded aluminium housing with opal PMMA with energy efficient electronic driver with following features:- Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 21 Watts; CCT 4000K; Dimension in mm (234); Nominal surge protection 2.5 kV;Power factor not less than 0.9; Minimum IP protection 20;

47) Supplying and installation of Recess mounting round LED luminaire equipped with fully enclosed precision die-cast aluminium construction,excellent pan with energy efficient electronic driver with following features:-Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 45 Watts; CCT 4000K; Dimension 215 mm cutout ; Nominal surge protection 2.5 kV;Power factor not less than 0.9; Minimum IP protection 20;

48) Supplying and installation of Recess mounting round LED luminaire equipped with fully enclosed precision die-cast aluminium construction,excellent pan with energy efficient electronic driver with following features:-Suitable for operating voltage and frequency: 130-300 Va.c, 50 Hz.; wattage 15 Watts; CCT 4000K; Dimension 155 mm cutout ; Nominal surge protection 2.5 kV;Power factor not less than 0.9; Minimum IP protection 20;

49) Supplying and fixing of 5 star rated, 1200mm sweep Ceiling fan complete with all accessories for use on 220/240 volts 50 HZ, single phase A/C Supply including wiring the down rod of standard length upto 30cm with 1.5 sq. mm FRLS PVC insulated, copper conductor single/ multi core cable etc as reqd.

50) Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

51) Providing and fixing M.S fan hook for ceiling fan including digging in RCC & making good the same complete as required.

52) Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

53) Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

53.1) 8 way, Double door

53.2) 12 way, Double door

54) Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

54.1) 8 way (4 + 24), Double door

54.2) 12 way (4 + 36), Double door

55) Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

55.1) Single pole

55.2) Single pole and neutral

55.3) Triple pole

56) Supplying and fixing 125 amps, 18 KA, TP MCCB in the existing TPN Distribution board/ panel board including testing & commissioning etc. complete as required

57) Supplying and fixing 100 amps, 18 KA, TP MCCB with Steel Enclosure including testing & commissioning etc. complete as required.

58) Supplying and fixing following rating, double pole, 240 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

59) Supplying and fixing Cable End Box (Loose Wire Box) suitable forfollowing single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 8/12 way, Double door SPN MCBDB

60) Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8/ 12 way, Double door TPN MCBDB

61) Supplying and fixing of 250mm sweep Fresh Air fan complete with suitable size louvers and PVC housing with all accessories suitable for use on 230 V , 50 Hz supply in the existing opening, including making good the damage , connection, testing and commissioning etc. as required.

62) Supplying and fixing of 300 mm size exhaust fan complete with suitable size louvers with all accessories suitable for use on 230 V , 50 Hz supply in the existing opening, including making good the damage , connection, testing and commissioning etc. as required.as required

63) Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

63.1) 4 X 25 sq. mm (28mm)

63.2) 4 X 50 sq. mm (35mm)

63.3) 3½ X 120 sq. mm (45mm)

64) Supplying and Laying of PVC insulated, PVC sheathed XLPE aluminium conductor armored cable of Following size, 1.1 KV grade conforming to I.S-1554/1/88

64.1) 4 X 25 sq. mm

64.2) 4 X 50 sq. mm

64.3) 3½ X 120 sq. mm

65) Providing and fixing 8 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

66) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

67) Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

68) Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

68.1) Upto 450 mm sweep

69) Fabrication, supply, installation testing & commissioning of indoor type compartmentalized panel board made out of 2mm thick CRCA sheet having separate cable and bus bar alley double door arrangement with two leaf door on front side and single door with double leaf on rear side with locking arrangement, having 400 amp TPN Aluminium bus bar with base frame made out of 50x50x6mm thick angle iron having 300 mm legs duly erection in ground with connection and interconnection with copper conductor PVC insulated cables/ insulated copper conductor strip of appropriate size and terminals blocks (on outgoing) including suppying and fixing following switch gears & accessories there in powder coating labelling earhing etc. complete as required 1. Having minimum size = 800mm x 1400mm x 300mm deep. (a) 250 amps, 4P, 36KA, 50HZ, 415V, AC MCCB L&T , legrand, Schnieder Make= 1 No (b) 100 Amps 3 Pole, 18KA 415V, 50HZ MCCB L&T,legrand, Schnieder Make=4 Nos (c ) Earthing studs 2 Nos (d) Danger plate – 02 Nos (e) Multimeter - 01 Nos. (e) RYB indicating lamp

70) Fabrication, supply, installation testing & commissioning of indoor low rise Lift platform suitable for domestic and public access with free standing facality & appropriate size including suppying and fixing following specification etc. complete as required. Model Type:- Low Rise Lifting Platform Rated Load:- 300 kg Rated Speed:- 20 mm/s Drive Type:- Electro-hydraulic Power Supply:- 230V, single phase, 50hz RCD protected fused spur Travel:- Up to 1000mm without a pit reccess, or 935mm with pit recess Footprint:- 1890mm x 1304mm Platform Size:- 1450mm x 800mm Location:- Internal or external Upper Gate:- Manual, self closing 900mm wide with steel infill Controls:- Standard landing call buttons,Landing controls post mounted at both levels, Car control rocker switch with emergency stop, Hold to run operation. Safety Features:- Platform and ramp safety sensitive devises, Manual emergency lowering. Weight:- 200 kg unladen Loadings:- Lift Base 5kn, gate if fitted 1kn per fixing Documentation:- Owners guide issued on completion.

Credit of Dismantled Items

71) Fire wood etc.

72) Old flush door shutter of various thickness and sizes with fitting etc.

73) Old M.S section / steel bars scrap / G.I pipes / C.I pipes etc.

74) Old scrap aluminium sections of various size and thickness.

75) Old cement asbestos or other hard board ceiling

76) Old chair with bracket

77) Less buyback of T5/ tube light/ conventional light etc. on as is where is basis.

78) Less buyback of 48 " Ceiling fan etc. on as is where is basis.

79) Less buyback of 10 " Fresh air/Exhaust fan etc. on as is where is basis.

80) Less buyback of MS conduit/ iron/ Steel items etc. on as is where is basis.

81) Less buyback of old aluminium wiring on as is where is basis.

KBG ENGINEERS