SPECIAL REPAIR TO OH SHED BLDG NO 86 (REPAIR BAY) BY DUCTS WIRE MESH, 02 X PARTITION, COMPLETE RE-WIRING ALONGWITH LIGHTINGS AND CHANGE OF GLASSES OF FD WKSP COY EME UNDER GE(SOUTH) MEERUT CANTT

Amount

Material and labour for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) including demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

Taking down cement plaster of any description from brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Material and labour for rendering 15mm thick in CM 1:6 on fair faces of brick wall or concrete surfaces , surfaces finished even and smooth without using extra cement complete all as secified and directed.

Material and labour for rendering 15mm thick in CM 1:6 on fair faces of stone wall or other than fair faces of brick work , surfaces finished even and smooth without using extra cement complete all as secified and directed.

Material and labour for preparation of newly plaster surface of wall and applying two coats of cement base paint over and including one coat of alkali resistant primer complete all as specified and directed.

Material and labour for preparation of new plaster surfaces of wall and applying three coat of white wash complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any postion not otherwise specifically provided for complete all as specified and directed .

Material and labour for providing reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone agg) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and Labour for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation fillings and mass concrete complete all as specified and directed.

Material and labour for use and waste formwork to sides of concrete foundation, footings, bases of column, plinth beams and similar work vertical or to batter for rough finished flat surface of concrete , complete all as specified and directed.

Material and labour for providing reinforced cement concrete (using 20mm graded crushed stone agg) as in columns, pillars,posts and struts complete all as specified and directed.

Use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surface of concrete complete all as specified and directed.

Material and labour for use and waste formwork to sides & sofits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors & beams, etc for rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour mild steel TMT bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed ) not less than 0.9mm dia or securing complete all as specified and directed.

All as per item No 14.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Material and labour for two coats of white wash on ceiling/chajja old surfaces including preparation of surfaces complete all as specified and directed

Material and labour for 3mm thick sheet glass, ordinary quality and glazing with oil putty beading/rubber beading area not exceeding 0.50 sqm each pane complete all as specified and directed (work height appx 12m).

Supply and fix in repairs expanded metal not exc 4 kg, cut to length, bent to shape required and welded to steel frame wor supplied and fixed to steel members upto a height of 12 mtr using necessary safety harness and equipments complete all as specified and directed (work height appx 12m).

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed.

Material and labour for mild steel angle iron door frame 40mmx40mmx6mm conforming to FE 410-0 incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars making good the floor in PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) to match the existing floor complete all as specified & directed.

Supply and fix mild steel framed work as in doors or gates of angle or other section with gusset plate, rails, braces etc ornamental and including either hooks and hinges or steel hanging door fitting to be prepared for hanging and also fastening conforming to Fe 410-0 or 310-0 complete all as sepcified & directed.

Supply and fix 1.00 mm thick mild steel, plain, black sheet in covering to door shutters; covering to door chowkats (frames); water tanks; water troughs: ducts; etc cut to size edges beads, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/ riveted seams including bending turning up mitred engles, stopped ends, outlets, etc. as required complete all as specified and directed.

Material and labour for preparation of new steel surface of any descripion over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed..

Material and and labour for preparation of steel & iron old surface over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed..

Material and labour for repair of rolling/sliding iron gate upto 40Sqm each by taking down and refixing the same after straightening of iron members and repairs including any steel member required to be changed to made functional complete all as specified and directed.

Material and labour for PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in hold fast block etc complete all as sepcified & as directed by Engr-in-Charge.

Material & labour preparation of old painted surfaces of wall and applying two coat of cement based paint of any colour complete all as specified & as directed .

Supply and fix in repair PVC pipes single socketed in any length with rubber ring joints, fixed to walls & laid under floors etc. 250 mm bore as in waste and rain water pipes complete all as specified.

Repairing of existing partition of ms work like angle iron, welded mesh etc by welding tightining etc (Note-Any steel member required to be replaced will be measured separately ).

Demolition of cement concrete (unreinforced) in ground floor and pavings and removing debries from site complete all as specified and as directed .

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundation and for manholes, pier holes etc n exc 10 Sqm on plan & foundation etc and getting out in soft/lose soil and levelling of bottom surface to required level complete all as specified and directed.

Removing excavated materials to a distance not exc 50 m and deposited where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc. 25cm thick in soft / loose soil complete all as specified and directed.

Material and labour for filling approved sand including spreading, levelling and ramming in layers n exc. 25 Cm thick in each layer complete all as specified and directed.

Material and labour for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring finished even and fair complete all as specified and directed.

Material and labour for machine pressed rubber moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade wih grey cement & no pigment complete all as specified and directed.

Material and labour pre-cast cement concrete block type B1 1:2:4 (using 20mm graded crushed stone aggregate) masonry with solid block etc 10cm in width and setting in (1:6) complete all as specified and directed.

Supply and fix in repair 3mm thick transparent polycarbonate sheet any size and in any type of frame with self tapping screws and including oil putty wherever required upto a height of 12mts using necessary safety harness and equipments complete all as specified and directed.

Taking down chowkhats or frame not exc. 1.5 Sqm each with shutters without taking off shutters, from the frame completeall as specified and directed .

Supply and fix Steel windows box type using 'P' section comprising double frame for gauge and glazed skelton shutter jointly with flat iron 40x3mm through out the complete frame including hinges, handle, tower bolts, stops, lugs etc all as shown on drawing.Note (i) For the perpose of measurement & payment double shutter with frame shall be considered as one unit (ii) Unit rate quoted against this item shall also include the iron mongreries shown on drgs (iii) gaurd bars glazing & Wire mesh shall be measured and paid for separately complete all as specified and directed.

Material & labour for 3 mm thick sheet glass ordinary quality and glazing with oil putty / beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix galvanised mild steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.14mm fixed with wooden beading for security wire staples complete all as specified and directed.

Material and labour for 25mm thick cement concrete 1:2:4 type B0 (using 12.5mm crushed stone agg) finished rough for laying of floor etc complete all as specified and directed by Engr-in-Charge.

Material and labour Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but n exc .18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.

Taking down carefully any type of battens or conduit point wiring with batten / conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed .

Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories/fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting/chases etc in walls, making good to walls, ceiling etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for One Bulb /Tube light / bell point/security light controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 46.00 here -in- before but for One ceilling fan/exhaust point controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 46.00 here -in- before but for One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 46.00 here -in- before but for One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 46.00 here -in- before but with 2.5 Sqmm Nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

Supply and fix switch piano flush type, 15/16 Amp single pole, one way 230 volts complete all as specified and directed.

Supply and fix socket outlet 3 pin, 05/06 Amp and 3 pin 15/16 Amps (2 in 1 Multipurpose) 230 volts complete all as specified and directed .

Supply and fix switch piano flush type, 05/06 Amp single pole, one way 230 volts complete all as specified and directed.

Supply and fix socket outlet 3 pin, 05/06 Amp 230 volts complete all as specified and directed .

Supply and fix stepped type electronic fan regulator flush AC, 230 volts, ISI marked with and including connector complete all as specified and directed .

Supply and fixing LED flood light fitting 1x50 Watt luminaries die cast fixed on roof or wall with suitable MS clamp complete with all accessories. Make Havells Model No JETA QUANTO PLUS or equivalent in Crompton/C&S/Philips

Supply and fixing LED security light fitting 1x45 Watt luminaries with die cast aluminium housing epoxy powder coated comprising high power LEDs enclosed with lens embeded PC cover with driver fixed in repair including security light bracket made of 32 mm dia GI pipe medium grade 1.5m long including flat iron clamps and suitable nut and bolt qrouted in wall and taking down old GI brakcet complete all as specified and directed. Make :- Havells Model No ENDURA Pearl Neo or equivalent inCrompton/Phillips/Surya

All as per Item No 57.00 above but capacity 30 watt. Havells Model No ENDURA CITYLITE PLATINAM PLUS or equivalent in Crompton/Bajaj/Phillips/Surya

Supply and fix LED Tube Rod 1x20 Watt suitable for MS batten with retrofit T8 polycarbonate with single side connection complete with all accessories including making connection and alteration in wiring as required complete all as specified and directed. Make-Havells, Model/Cat Part No PHOTONULTRA2.01213T8SSTL20WLED865 PC or equivalent in Wipro/Crompton.

Supply and fix of ceiling rose, 3 terminal PVC polycarbonate isolated body complete all as specified & directed .

Taking down carefully unserviceable sub main wiring of any size and type, removing material from site for taking credit and making good the disturbed surfaces of walls, ceilings etc including two coats of white/colour washing/distempering etc to match the existing complete all as specified and directed .

Material and labour for sub main wiring with 2x4.00 Sqmm nominal cross sectional area (two single core FRLS cable of 4.00 Sqmm for phase and neutral + o1 single core cable of 4 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, FRLS unsheathed, copper conductor cable with and including continuous earth wire of size 4.00 Sqmm nominal cross sectional area, single core, PVC insulated, FRLS copper conductor cable drawing into rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories/fittings, brass screws, washers etc and connected to common earth dolly including taking down unserviceable sub main / service main wiring including all cutting/chases etc in wall, making good to walls etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed. (Note : One meter of conduit along with 2x4.00 sqmm wire and one 4.00 sqmm earth wire shall be measured as one RM length.)

Material and labour for sub main wiring with 2x6.00 Sqmm nominal cross sectional area (two single core cable of 6.00 Sqmm for phase and neutral + o1 single core cable of 6 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, FRLS unsheathed, copper conductor cable with and including continuous earth wire of size 6.00 Sqmm nominal cross sectional area, single core, PVC insulated, FRLS copper conductor cable drawing into rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories/fittings, brass screws, washers etc and connected to common earth dolly including taking down unserviceable sub main / service main wiring including all cutting/chases etc in wall, making good to walls etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed. (Note : One meter of conduit along with 2x600 sqmm wire and one 6.00 sqmm earth wire shall be measured as one RM length.)

All as per item No 63.00 above but using two single core cable of 1.5 Sqmm for Phase and neutral + one single core cable of 1.5 Sqmm for earth wire complete all as specified and directed.

Material and labour for sub main wiring with 4x10.00 Sqmm nominal cross sectional area (four single core cable of 10.00 Sqmm for phase and neutral + o1 single core cable of 10 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, FRLS unsheathed, copper conductor cable with and including continuous earth wire of size 10.00 Sqmm nominal cross sectional area, single core, PVC insulated, FRLS copper conductor cable drawing into rigid non metallic PVC concealed conduit of suitable size, medium grade with all conduit accessories/fittings, brass screws, washers etc and connected to common earth dolly including taking down unserviceable sub main / service main wiring including all cutting/chases etc in wall, making good to walls etc including two coats of white/colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed. (Note : One meter of conduit along with 4x10.00 sqmm wire and one 10.00 sqmm earth wire shall be measured as one RM length.)

Supply and fixing of ceiling fan BEE 5 star rated with ISI marked white colour, 1200 mm sweep, copper winding, single phase, 220 volts, 50 Hz, with blade set of 3, with down rod as per site requirement including connection three core flexible copper wire 0.75 Sqmm multistranded from ceiling rose to fan connector, wtih and including fan hook duly grouted on roof including taking down existing ceiling fan from the location and depositing to AGE E/M store yard complete all as specified and directed. . Make - Havells, Model - ES 50 or equivalent in crompton/orient.

Taking down carefully unserviceable distribution board of any capacity including wooden board and making good the disturbed surfaces of walls, etc including two coats of white/colour washing/distempering etc to match the existing complete all as directed.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 12 way with 200 Amps rated copper bus bar and IP-43 & IK 09 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amp rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer-in-Charge.

Supply and fixing vertical loadline sheet metal enclosure double door, triple pole and neutral (TP&N vertical loading) AC, 415 volts, 04 way , with 200 Amps rated copper bus bar and IP-43 & IK 09 protection, with the inbuilt provison for fixing of 1 No MCCB of XT1160 frame suitable upto 160 Amp and 12 Nos MCB'S inside of DB, with metal door and flush to wall including grouting and cutting in existing wall and making good distrubed surface with two coats of white/colour washing/distempering etc to match the existing one complete all as specified and directed.

Supply and fixing MCB, SP, AC, 240 volts of 06 to 40 Amp C curve, 10 kA, confirms to IS/IEC 608981:2002 and making connections complete all as specified and directed.

Supply and fixing MCB, SP, AC, 240 volts of 63 Amp 'B' curve, 10 kA, confirms to IS/IEC 608981:2002 and making connections complete all as specified and directed.

Supply and fixing MCB, SPN, AC, 240 volts of 40 Amp 'B' curve, 10 kA, confirms to IS/IEC 608981:2002 and making connections complete all as specified and directed.

Supply and fixing MCB, SPN, AC, 240 volts of 63 Amp 'B' curve, 10 kA, confirms to IS/IEC 608981:2002 and making connections complete all as specified and directed.

Material and labour for MCCB 4 pole 160 Amp18 KA of XT1 160 frame fixing in sheet metal enclosure on wall, 415 volts, 50 Hz using thimble/lugs properly including all nuts bolts required for fixing complete all as specified and directed..

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed. Note: After completion of work if desired test result is not obtained the earthing is to be redone without any extra cost to deptt.

Material and labour for laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 25 Sqmm 3.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc including taking out old unserviceable LT cable complete all as specified and directed.

Material and labour for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified and directed.

Material and labour for contineous brick protection to cable with width equal to the length of the whole sub class 'B' bricks laid on edge complete all as specified and directed.

Supply/laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Jay Ambay Enterprises

Arun Construction Co.

BASANT ENTERPRISES