SPECIAL REPAIR TO BLDG NOS. P-28 29 30 AND 31 AT AF STATION DEVLALI

Amount

Cutting openings through stone walls built in cement mortar for door, windows and other openings or enlarging existing openings etc or cutting out defective masonry for underpinning including providing, fixing and removing shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises all as specified and directed by Engineer-in-Charge.

Taking down cement plaster any description on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Dismantling ceiling boarding, any description, fixed in any position with nails including cover fillet complete all as specified and directed.

Dismantling of asbestos cement(corrugated /semi corrugated etc) sheet in roof covering including ridge complete all as specified and as directed.

Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings dressed stonework and pre cast concrete articles complete all as specified and directed.

Material and labour for cutting holes in stone walls built in cement mortar for exceeding half brick but not exceeding one brick inserting holdfasts and making good dismantled portion in cement morter 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

Taking down chowkats or frames with shutters of area not exceeding 1.5 sqm (without taking off shutters from frame) all as specified and directed

Dismantling boarding, any description, fixed in any position with nails including cover fillet complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) all as specified and directed

Dismantling of wrought iron or mild steel work of any description any height not otherwise provided complete all as specified and directed.

Material and labour for 75 mm thick sub base in Plain cement concrete (1:4:8) type D2 using 40mm graded stone aggregate all as specified and directed.

Material and labour for cement concrete type C1 (1:3:6) (20 mm graded broken stone aggregate) as in plilnth protection and paving 75 mm thick laid in slope finished even and fair incl making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified and as directed.

Material and labour for coloured ( light shade) vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 15 mm thick screed bed or bedding layer CM 1:6 complete all as specified and as directed by Engineer in Charge

Material and labour for coloured ( dark shade) vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 15 mm thick screed bed or bedding layer CM 1:6 complete all as specified and as directed by Engineer in Charge

Material and labour for coloured ( light shade) vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

Material and labour for machine cut kota stone flooring of size 18 to 20 mm thick (mirror finished) over and including 20 mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the floor including rubbing and polishing complete and moulding at edge if required all as specified and directed.

Material and labour for mirror polished kota stone of 18-20 mm thick in window/ventilators jamps, cills, riser and Trades of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 10mm thick backing coat in cement mortar (1:4), surfaces finished even and rough to receive tiles, including Dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises, all as specified and directed.

Labour for round chamfering, to the edges of granite splays or arris in firework exceeding 15 mm but not exceeding 50 mm wide on granite stone shelves complete all as specified and directed.

Material and labour for sand filling under floor or in Foundation including watering & consolidation etc complete all as specified and directed.

Material & labour for machine pressed coloured rubber moulded precast concrete interlocking paver blocks with pigment of any shape and size, conforming to IS 15658-2006 of 60 mm thickness, M-35 grade all as specified and directed.

Material and labour for brick work with fly ash bricks (old size brick) straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 all as specified and directed.

Material & labour for providing plain cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate as in bed plate, hold fast, coping etc all as specified and directed by Engr-in-Charge

Material and labour for false ceiling work of aluminium snap grid system of size 600x600 mm frame work for false ceiling with aluminium angles of size 23.5 x 23.5 x 1.5mm fixed to wall with GI screws and aluminium tee section of size 37.5 x 37.5 x 1.5mm in main and cross runners fixed at 60 cm c/c and tied to existing roof/truss/rafters complete all as specified and directed.

Material and labour for hanging of aluminium false ceiling grid with 3mm dia GI wire (upto necessary required length & 1.2 Mtr c/c fixed to sloping roof (rafter/purlin/trusses) complete all as specified and directed.

Material and labour for non asbestos fibre cement building boards 6 mm thick (one side embossed design) fixed or laid /inserted to aluminium grid frame work in ceiling with clips all as per manufacturer's instructions complete all as specified and directed Make : Armstrong or equivalent in approved makes.

Supply and fix 1.0 mm thick plain, black mild steel sheeting as in valley gutters, drip, berge board etc and straight flashing (length and girth as fixed) complete all as specified and directed.

Supply and fix for Anodised powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators 114.30 mm x 44.45 x 3.18 mm with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Supply and fix for anodized aluminium door shutters powder coating (any colour decided by GE) of thickness not less than 50 micron aluminium section in which size of shutter top member 47.62 x 44.45 x 2.00 m , shutter bottom member 100 x 44.45 x 2.00 mm, shutter vertical members 47.62 x 44.45 x 2.00 mm and shutter lock rail member of size 63.50 x 44.45 x 2.40 mm including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F Anodized aluminium powder coated window and ventilator shutters, three track, glazed/gauzed shutters made out of aluminium section as mentioned below and glazed with frosted glass /gauzed fixed with glazing clips, rubber beading/gasket abd star lock type handles complete all as specified and as directed :- (a) window frame top and bottom size 92.00 x 31.75 mm x 1.50 mm (b) Window frame sides size 92.00 mm x 31.75 mm x 1.50 mm (c) Window shutter for top and bottom size 52.00 x 18.00 mm x 1.48 mm (d) Window shutter for sides (vertical) of size 30.00 mmx20.20mm x1.40mm (e) Window shutter inner lock rail (vertical) size 40.00 mm x 18.00 x 1.00 mm. Note : Glass /wire mesh shall be paid separately.

Supply and fix for 5.5mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Supply & fix stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as directed.

Supply & fix for double action floor door stoper/spring hydroulically regulated made up of minium 1.25 mm thick aluminium alloy sheet foundation bore, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in fixed including taking down and refixing aluminium shutter in the same opening.

Supply & fix in repairs aluminium (die cast) body door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters of 851 to 1000mm in width & weight between 61 to 80 Kg and fixed all as specified and directed.

Supply & fix in repair mortice lock brass of size 100 mm, 4 levers vertical type fixed complete all as specified and as directed

Supply and fix aluminium, anodised, barrel tower bolt 200 mm long, of extruded section and fixed all as specified and as directed

Material and labour for Precast/cast in situ Reinforced cement concrete (Nominal mix) Type B1 1:2:4 (20 mm graded stone agggs) as in lintels and the similar work complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends binding with mild steel annealed wire not less than 0.9mm dia or securing clips, complete all as directed.

Supply and fix for TMT bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping ends for stirrups all as specified and directed.

Use and waste of formwork (flats) to sides and soffits of floor or roof beams , lintels, cantilever shelves etc including supports, overhang etc also splays between floors and beams etc all as specified & directed.

Supply and fix trapezoidal COLOURBOND XRW steel prfile sheet of overall width 1072 mm and nominal 28.50 mm deep ribs with subtle suare flutingin the five pans at nominal 203 mm centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage water through the lateral overlap including providing crimp at eves level shape of crimp complete all as specified and directed. The feed material COLOURBOND XRW steel used as per AS/NZS 2728 type 4 nominal 0.50 mm total coated thickness (0.45 mm BMT) of Hi strength with minimum 550 Mpa yield strength, AZ150 (Min. 150 g/m2 total of both sides ) hot dip metallic coating of 55 % Aluminium Zincto AS 1397 (ZINCALUME steel ) and lead free super durable paint top coat with inorganic pigment with ThermatechTM Technology. The sheet shall have a total thickness of 35 µm super durable polyester quality paint system 20 µm on exposed surface and 5 µm reverse polyester coat on back surface over 5 µm primer coat on both surfaces. The paint system should have stable resin and inorganic pigments for paint durability and lead free for water harvesting. Clour : Surfmist Make : TATA Blue Scope steel /Jindal or eqivalent in approved makes.

All as per item No. 42 here-in-before but ridge only

Supply and Fix for mild steel work in framed brackets of square pipe, angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles as necessary and similar work including bending and welding angles as necessary confirming Fe- 290 Grade E-165.

Material and labour for mild steel as in wind ties, valley gutter strip etc hold fast and brackets for holding boarding etc. complete all as specified and as directed.

Material and labour for bands, straps, supports or stays for eaves gutter, rainwater, ventilating pipes, including bolts/welding, if required; hooks (stay), and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and directed

Supply and Fix for Framed work such as grills, gratings door chowkats etc. with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed

Material & labour for rendering 10 mm thick cement plaster in CM 1:6 over 10mm thick cement plaster in CM 1:6 (as in backing course) on stone masonary surface of wall and finished even and smooth without using extra cement all as specified and as directed. (Note : Rendering should be in Two layers)

Material & labour for rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement all as specified and as directed.

Material & labour for rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement all as specified and as directed.

Material and labour for Preparation of new plastered surface of wall by applying 1.5 mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

Materials and labour for preparation of new steel surface of any description over 10cm width or grith not otherwise described and applying two coats of synthetic enemal paint over one coat of red oxide primer, complete all as specified and directed.

Materials and labour for one coats of synthetic enamel paint on old steel surfaces of any description, over 10 cms in width or girth, including preparation of surfaces, complete all as specified and directed.

Supply only pre -coated fancy type drapery rod 25mm dia fixed with fancy type matching pair of brackets fixed with screw (Note : Brackets will be measured seprately)

Supply and Fix for fancy type brackets to suit pre-coated curtain rod 25 mm dia all as specified and directed

Supply and Fix for Peg set of Six powder coated fixed with chromium plated brass screws and wooden and plastic cleats (minimum weight 190 gms) complete all as specified and directed.

Dismantling posts or struts (wood ,steel or RCC) any section, including taking out embedded portion and making good disturbed ground posts embedded in concrete all as directed.

Dismantling of fencing wire mesh any type and description all as specified and directed.

Supply and fix rolled mild steel Framed work as in doors or gates of angle or other section confirming to Fe 410-W with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Excavation in post holes ( or similar holes) each not exc 0.5 Cum and getting out in any type of soil, and removing excavated soil to a distance not exceeding 50 m distance and making good surface complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified and directed.

Material and labour for PCC (1:3:6) type C2 using 40mm graded stone aggregate as in foundation all as specified and directed.

Supply and fix mild steel, angles in posts and strut in fencing including cutting tops to shape, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe290 Grade E-165 complete all as specified and directed.

Supply and fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and the screwed the other to be fitted with washers and one hexagonal or square nut, exceeding 5 cm but not exceeding 10 cm long, dia of shank 5 to 10mm all as specified and directed..

Supply only chain link fencing with knurling made out of 3.8 mm to 4 mm dia, galvanized MS wire, size of mesh 50mm x50 mm complete all as specified and directed by Engr in Charge.

Fixing only chain link fencing of wire mesh size 50mm x50mm including line wires, and type of standard rails, straining bolts etc. including provision of binding wire all as specified and directed.

Supply and fix mild steel round bar 10mm dia and over, cut to length, bent to shape required, including cranking conforming to Fe-410-W (Gde E-250) quality-A or Fe 290 (Gde E-165) as in strengthning bars complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description, not exceeding 10cm width or girth, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified.

INTERNAL ELECTRIFICATION

Taking down carefully copper/aluminium point wiring (light, fan, socket or power etc) on TW batten/PVC casing caping, steel surface /PVC conduit including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Material and labour for point wiring complete with two single core, PVC insulated, unsheathed, multi stranded bright annealed copper conductor cable, 1.5 Sqmm 1100 volts, anti termite eco friendly FR grade drawn through and including heavy duty PVC casing and caping not less than 25 mm dia and accessories concealed on walls, ceiling etc. on and including ncluding PVC board with earth dolly arrangement with surface plate for mounting switches, sockets, regulators etc and one run of 1.5 Sqmm PVC insulated, unsheathed, multistranded, copper conductor cable FR grade as earth wire and connected to common earth dully complete for complete all as specified and directed for folowing:-

(a) One ligh point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One bell point controlled by one push button.

(d) One 3 pin socket out let 5 Amps on same board.

(e) One 3 pin socket out let 5 Amps on independent board.

All as per item No. 69.10 above herein before but for 2.5 Sq.mm cable size and one run of 1.5 Sq.mm cable as earth wire for one 3 pin socket outlet, 15 amps controlled by one switch.

Supply and fix switch piano flush type single pole one way 5 Amp complete all as directed.

Supply and fix switch piano flush type single pole one way 15 Amp complete all as directed.

Supply & fix in repairs fan regulator electronic solid state with various steps with variable speed suitable for ceiling fan of size 900 to 1500 sweep working on 230 volts, AC supply with all necessary connection complete all as specified and as directed.

Supply and fix bell push 5 Amps SP, one way suitable for 230 Volts flush type complete all as specified and as directed.

Supply and fix electric bell ding dong AC 230 Volts, Single pole complete all as specified and as directed.

Supply and fix socket out let two in one, 5 pin 5 Amp flush type complete all as directed.

Supply and fix socket out let two in one, 3 pin 5 Amp and 15 Amp flush type complete all as directed,

Supply and fixing ceiling rose 3 phase / PVC / polycarbonate insulated body 65 x 50 mm, two or three terminals all as specified and as directed .

Supply and ceiling light fitting 36 Watt LED energy saving environmental friendly long life and accessoriess fixed false ceiling 60 cm x 60 cm in size including connection with PVC copper 1.5 Sq.mm 3 core cable etc complete all as specified and directed. Make: Crompton Model No. LCTLRN-I-36-FO-CDL or equivalent in philips, Havells, Wipro as approved by GE.

Supply and fix in repairs sheet metal enclosure for 8 way MCB SPN distribution board, 240 volts double door with DIN rail bus bar, neutral link, earth terminal etc with IP-43 IK-09 protection complete all as specified and directed.

Supply and fix in repair MCB SP 6 to 32 Amps 240 volts, C series of breaking capacity 10KA including making connection complete all as specified and directed.

Supply and fix in repair MCB SPN 6 to 32 Amps 240 volts, C series of breaking capacity 10KA including making connection complete all as specified and directed.

Material and labour for providing earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) surrounded with alternate layer of charcoal and salt as directed with top edge of the plate not less than 1.5 mtres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion including earthing pit in PCC 1:3:6 type C-0 & 40mm thick precast RCC cover in 1:2:4 type B1 reinforced with 8mm dia TMT bar @ 75mm c/c both ways with 02 Nos lifting handles of 12mm dia MS plain bar, GI pipe 20mm dia light grade with funnels & wire mesh for watering and 15mm dia medium grade GI pipe for earth lead protection etc including necessary excavation and earth work in any type of soil complete all as specified and as directed. Note:-(i) GI lead wire and protection pipe upto 7.5mtr is deemed to be included in the quoted rate. (ii) Earthing required for External electrification shall also be measured under this item.

Supply, laying, testing and commisioning of LT XLPE insulated/PVC heavy duty armoured cable 1100 volts grace UG stranded aluminium conductor electric cable cross sectional area 10 Sqmm 2 core including necessary connection with provision of lugs and cable gland fixing arrangements all as specified and directed.

Supply and fix for power shield 32 A DP mini MCB with enclosures single phase 240 Volts including making connection complete all as specified and as directed. Make : Standard Cat No. DSMNCDPA032 or equivalent in Havells /Siemens

Supply, laying, testing and commisioning of LT XLPE insulated/PVC heavy duty armoured cable 1100 volts grace UG stranded aluminium conductor electric cable cross sectional area 10 Sqmm 4 core including necessary connection with provision of lugs and cable gland fixing arrangements in repairs all as specified and directed.

Supply, laying, testing and commisioning of LT XLPE insulated/PVC heavy duty armoured cable 1100 volts grace UG stranded aluminium conductor electric cable cross sectional area 25 Sqmm 4 core including necessary connection with provision of lugs and cable gland fixing arrangements in repairs all as specified and directed.

Supply and fix in repairs sheet metal enclosure for DB's MCB TPN, bus bar, 4 way, 415 volts double door with detachable gland plate vertical type complete all as specified and directed.

Supply and fix repairs sheet metal enclosure MCB TPN 4 way distribution board AC 440 volt, double door with DIN rail bus bar, neutral link, earth terminal etc IP-43, IK 09 protection complete all as specified and directed.

Supply and fix MCB TPN 6-32 Amps 415 volts, C series of breaking capacity 16KA including making connection complete all as specified and directed.

Excavation in trenches in hard/dense soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of water pipe lines and getting out soft / loose soil complete all as specified and directed

Excavation in trenches in hard/dense soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of water pipe lines and getting out hard soil complete all as specified and directed

Returning, filling in and ramming with approved excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick all as specified.

Removing excavated soil to a distance not exceeding 50 mtre and depositing where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

Supply and laying Double walled corrugated (DWC) duct (Dura - Guard) as per IS - 14930 Part -II for LT UG cable protection including coupler, elbows, T-joint, bends, etc and test report Make : Dura line/Gemini/Rex of size 38 mm complete all as specified and as directed.

Note : The amount against Schedule of Credit on Page No. 34 shall be deducted from the total amount quoted against Sch 'A' while deriving lum Sum for Acceptance.

Anand Trading Co