SPECIAL REPAIR TO LIVING IN ACCN FOR NCOs / NC(E ) AT AF STN NAL

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving exc.15 cm thickness above ground level and removing the rubbish outside MoD land complete all as specified & directed.

Material and labour 75mm thick PCC 1:4:8 type D-2 ( using 40mm graded aggregate) thick as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed.

M&L Providing and injecting emulsion for post constructional anti termite treatment using chemical chloropyrihos 20% EC emulsifiable concentrate along the external wall of building below concrete or masonry apron using chemical emulsion @ 2.25 liter per linear metre including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 cement : 2 coarse sand ) in apron complete all as specified and directed.

M&L Providing and injecting chemical emulsion for post constructionl anti termite treatment using chemical chloropyrihos 20% EC emulsifiable concentrate of soil under existing floors using chemical emulsion @ 0.5 liter per hole 300 mm apart (both ways Horizontal and vertical) and plugging holes with cement mortar 1:2 (1 cement : 2 coarse sand ) to match with the existing surface complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick over and including 20mm thick screed bed /bedding layer in cm 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over backing coat laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 10mm thick backing coat or bedding layer in cm 1:6 as specified and directed.

Dismantling floor, hearth wall tiling incld cement mortar bedding (but not backing) removing serviceable tiles to store & rubbish off the premises. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Material and labour Glazed ceramic coloured tiles 7 to 8mm thick (Square/rectangular ) dark/printed in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat cement slurry and pointed with coloured cement to match, over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and directed.

Supply and laying glossy finished chequered cement concrete tiles 30mmx30mmx22mm thick made by table vibratory method set, jointed and pointed in neat cment slurry as in floors with white cement & pigment over 20mm thick screed bed complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement mortar (1:4) including pointing in white cement (1:2) using marble duet with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and including rounding of edges of granite slabs 10 to 20 mm thick by grinding and rubbing and finished smooth, coloured as approved by GE all as specified and directed. Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra paid on this.

All as per description of serial Item no. 13.00 here in before but as on vertical surfaces and over 10 mm thick rendering in CM 1:4.

Material and labour 75mm thick PCC 1:3:6 type C-2 ( using 20mm graded aggregate) as in plinth protection laid in alternate bays, surface finished even & smooth without using extra cement including making joints complete all as specified and directed.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Demolition of brick or stone masonry built in cement mortar incl all quions, arches, pillar etc. complete all as specified & directed.

Material and labour brick work with sub class -B bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6. complete all as specified & directed.

All as per description of serial Item no. 18.00 here in before but as in half brick thick wall built in CM 1:4.

Material and labour 15mm thick rendering on other than faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour two coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Preparing new plastered surface of wall and applying two coat of oil bound distemper emulsion over one coat of primer over two coat of wall care putty complete all as specified and directed.

Preparing new plastered surface of wall applying two coats of acrylic emulsion exterior paint over coat of primer, tint as approved by GE in camouflage pattern complete all as specified and directed.

Material and labour for complete removal of existing wal treatment and applying two coats of acrylic emulsion exterior paint over coat of primer, tint as approved by GE in camouflage pattern complete all as specified and directed.

Material and labour for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required, and applying one coat of white lime wash complete all as specified.

Material and labour for complete removal of existing wall treatment and and applying two coat of oil bound distemper emulsion over a coat of primer over two coat of putty complete all as specified

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 125x60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

S&F MS Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. including cutting tops to shape as directed, embedding in concrete and screwing etc, wind ties for roof including bolts drilling holes, notching for wire etc, flat iron fillets (for securing GI sheet etc) and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to Fe-290 Gde E-165

S&F in repair MS Framed work such as grills, gratings, frame for false ceiling etc. with making good, welding work, bolting or reveting similar work conforming to Fe.290.Gde-E-165

Supplying & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used insted of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS framewelded, sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement complete all as specified in SSR Part -II.

S & F factory made Glazed & Skeleton shutters 35mm thick open rebated & prepare to received glass, gauge etc edges of framing plain chamfered or rounded in window, ventilator etc are provided with stiles and rails in 2nd class hard wood all as specified in SSR part-I, section 8 clause 8.20(b).

S&F factory made 35 mm thick 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm BWP commercial ply with commercial veneering on both faces; supplied and fitted to chowkats

Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re-fixing in same opeing after re-securing or easening and adjusting including repair complete all as specified.

Supply and fixing extruded Aluminium alloy butt hinge with galvanised mild steel hinge pin, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150 mm size extruded aluminium alloy handles fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed.

Supply and fixing in stainless steel wire cloths 0.45 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed..

Supply and fixing 140mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed to door shutter fixed with stainless steel screws complete all as specified and directed.

S&F in repair heavy duty Stainless steel (Grade 305) curtain rods 25mm dia including chromium plated supporting brackets as per sample approved complete all specified and directed.

S&F in repair Stainless steel (Grade 305) ornamental type brackets suitable for curtain rods of 25mm dia as per sample approved all as specified and directed.

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F factory made box type steel window 1.25mm thick ERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage and glass shutter comprised gaused glazed & Skelton shutter ERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) MS pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10 mm squre guard bar @ 10 cm c/c viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed skelton shutterof window (x) 3mm thick sheet glass ordinary quality and with oil putty in squre n exc 0.50 sqm in each pane fixed in glazed /guage skelton shutter of window xi) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Note: (i) Windows shall be povided as per the TD of Chief Engineer Chandigarh Zone, TD-219 i.e typical details of Box window (Steel) with fly proof shutter. (ii) The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account.

S & F mild steel box type ventilator fixed type with glazing bar with mesh & glass all as per item ser No 51 above

Material and labour for surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer, including preparation of new wooden surface.

Material and labour for preparation of old wooden surfaces of any description not other describe over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide.

Material and labour for preparation of old steel surfaces of any description not other describe over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not other describe n exc10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide.

Material and labour for preparation of old steel surfaces of any description not other describe n exc10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling AC sheet (Corrugated/Semi-corrugated) in roof covering .

Rolled sections as in main and cross beams, hip and jack rafters; purlins, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

M/L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by engineer-in-charge.

M/L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by engineer-in-charge.

S&F in repairs ceiling board of Arm Gyp-FB ceiling 600mm x600mmx9mm snow frost vinyl face, washable metallized polyster foil backing, vinyl covered edges, suspended ceiling having strength 7 kg/Sqm complete all as specified and directed, Make : Amstrong, Gyptech, Dexune

Taking up or down 15 mm dia steel tubing & connections including clearing for refixing or removal to store.

All as per description of serial Item no.63.00 here in before but 20mm bore tubes.

S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

All as per description of serial Item no. 65.00 here in before but 20mm bore tubes.

Cleaning and removing all scale and dirt from RCC / PVC tank capacity of tanks exc. 250 ltrs and up to 500 ltrs by emptying, drying, cleaning with chlorine/washing powder by scrubbing the dust with wire brush from tank by removing inlet and outlet pipe and refixing inlet and outlet pipe with new tank connection fitting in the same position after cleaning and marking the date of cleaning on the tank with paint complete all as specified and directed. Note:- "Writing "CLEANED ON DD/MM/YY" on service water tank with letters or figures (Block. Roman) of size 5 cm high and min 5cm wide each.

Dismantling water tanks any type of capacity Exc 250 but n.exc 500 liters

S&F 500 liter capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified .

S&F in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as specified and directed

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore

S & F in repair long body stop valve / Angle cock 15mm bore fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S & F in repair long body stop valve15mm bore fancy type chromium plated with long shank and cup(concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair 15mm long body bib taps long shank cast copper alloy with crutch or butterfly handle screwed for iron piper or for brass ferrule

S&F in repair Pillar taps long body fancy type with capstan head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends

S &F in repair chromium pated shower rose 125mm size with or without swivel joints, any size including fixing to 15 mm bore steel pipe or union

S & F in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats

S& F in repair Soap Dish as approved Design complete all as specified and directed by Engr in Charge .

S&F in repairs waste down pipe 32/40mm bore for wash basin complete all as specified and directed

S&F vitreous china wash down water closet pan pedestal pattern ( type white including PVC seat cover and CP jet with pipe, connection to waste pipe and flushing pipe complete fixed in repair. Make - Hindustan/Cera/Neycer

S & F in repair 10 Ltr capacity PVC valve less syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, L-Bend complete all as specified and directed

S&F in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket and CP waste coupling 32 mm bore complete all as specified and directed

Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed

S & F 110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to wall/floor, incl PVC straps/clamps complete all as specified and directed

S & F 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls/floor, incl PVC straps/clamps complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore with access door complete all as specified and directed

S&F PVC (SWR) 110mm bore Junction (single T) equal or unequal with access door complete all as specified and directed

S&F PVC (SWR) bends of 75 mm bore complete all as specified and directed

S & F 75mm bore PVC SWR Junction single (Single T) equal or unequal with access door complete all as specified and directed

S&F PVC (SWR) 75 vent cowl complete all as specified and directed

S&F PVC (SWR) 100 vent cowl complete all as specified and directed

S & F in repair 75mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 100mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Taking up/down 40 / 20 mm bore GI water tubing and connection from trenches/ walls/ floors for replacement complete all as specified and directed. Note : Necessary earthwork, if any, will be measured separately under relevant items.

Supply, laying and testing of 40 mm bore GI tubing (medium grade) with new fittings,fixed to walls, and ceilings or laying in floor/trenches as directed .

Supply, laying and testing of 20 mm bore GI tubing (medium grade) with new fittings,fixed to walls, and ceilings or laying in floor/trenches as directed .

Supply and fixing 20 mm bore Gun metal gate valve with iron wheel head, screwed both ends for iron pipes or for unions as directed .

Excavation in trenches in soft / loose soil not exceeding 1.5 metre wide for foundation etc or for shafts, wells cesspits, manholes etc not exceeding 10 Sqm on plan and not exceeding 1.5 metre in depth and getting out .

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25 cm .

Removing excavated material not exceeding 50 metre and deposited where directed at a level not exceeding 50 metre above the starting point in soil .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down unserviceable submain wiring alongwith batten /PVC conduits or etc and making good disturbed surfaces of walls/floors and match the existing surface all as directed at site.

Taking down unserviceable main switches, DBs / changeover switch alongwith Teak wood boards etc and making good the disturbed surfaces of wall / floors to match the existing surface all as directed at site

Taking down carefully old MCB s/Isolators any type by unscrewing from board complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring using 1.1 KV grade single core FR-LSH flexible cable , 694:2010, having multi-drawn thin strands of electrolytic copper conductors and insulation for Phase, neutral, and earth continuity conductor Confirming to IS Connecting to earth dolly, colour-coded as per IS 11353 :195, drawn in medium grade UPCV surfacel recessed conduits, conforming to IS 9537 (Part-3) 1983, of size not less than 20mm NB, including cutting chasses, factory made not less than 1.2mm thick sunken, modular flush sheet galvanized metal enclosure having zinc Coating not less than 120 GSM, conforming to IS 14772 :2000, having top, bottom, side and back-wall knockouts for Conduit entry from any direction, suitable modular cover-plates and making good of disturbed surface of wall/ ceiling/ floor etc complete all as specified in 1S 732 : 2019 and directed by the Engr-in-Charge.

Description complete all as per item No 111 here in before but 1.5 sq mm cable size and 1.5 sq mm earth continuity wire for one 3 pin socket outlet, 5 amps on Independent board.

All as per item Srl No 112 above but for same board .

All as per item No111 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 15 Amps on independent board.

S & F in repair modular Switch Socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal all as specified and directed.

S & Fin repair modular Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal all as specified and directed.

S & F in repair modular switch type single pole one way 5 amp 240 volts, all as specified and as directed.

S & F in repair modular socket 2 in one , 5 Amp, flush type 240 volts, all as specified and as directed.

M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed.

S&F sheet metal enclosure 20 Amps single pole and natural with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 20 Amp fixed properly in concealed position including making good disturbed surface all as directed by Engineer-in-charge. Cat part No 811956 of indoasian (opti pro) or equivalent in Legrand/ Seimens/ Havells

S & F Exhaust fan 300mm dia including louvers AC single phase 240 volts of size 300 mm sweep(metal body) and not less than 900 RPM including flexible wire 3 core 1.5 Sqmm from ventilator fan to ceiling rose all as specified and as directed. Make : Havells or equivalent in BAJAJ/USHA

Taking down carefully old serviceable ceiling fan from its existing/original position incl its electrical connection and down rod and then depositing it to MES Store for reuse and all as directed and specified .

S & F Energy saving ceiling fan 1200 mm sweep with double ball bearing with ISI marking and BEE 5 star rated complete including provision of three core copper wire of suitable size,down rod , electronic regulator etc connected from ceiling rose to fan and marking MES No in black paint complete all as specified and as directed. Make : Havells Model: ES 50 5 star or equivalent in Crompton/Usha/Bajaj

S & F sheet metal enclosures MCB SPN DB 8 way with 200 amps rated busbar, 240 volts, as per IS-8623 with double glazed door for incorporating MCBs,IP-43 „ including taking down old unserviceable single phase DBs, all as specified and as directed. Cat part No 811807 of indoasian (opti pro) or equivalent in seimens/ legrand/ Havells

S & F MCB SPN 40 amps 'C' series breaking capacity 10 KA, 'C, curve 240 volts, 50 Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc. Make : L&T/legrand/Havells/ABB

S&F MCB SP, 6 to 32 Amps, 'C' series breaking capacity 10 KA, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc. Make : L&T/legrand/Havells/ABB

S & F in repair modular stepped type (0-4 step) electronic regulator for ceiling fan, 240 volts, 100 Watts, single pole, including connecting, testing complete all as specified and as directed. Make: Anchor/Plaza/Crabtree/Havells

M&L for sub-main wiring in concealed PVC conduit with two single core 6 sq mm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of masonry including 20 mm dia non-metallic PVC conduit fixed in wall including 4 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete. Note : 1 run of PVC conduit & 3 run of copper cable shall be measured as single unit.

Supply and fix LED tube light fitting with LED T8 tubular lamp 20 Watt IP 20 Liner with extruded aluminum/PVC body and PC diffuser complete with inbuilt driver. The lamp shall be 1200 mm length with G13 base. The 20 Watt system shall be operating at 220-240V AC supply having internal driver, surge protection 2 KV, ambient temperature -20 to 45 degree C, frequency 50 to 60 Hz, The system efficiency must be between 80-100 lumen/watt, with 70% lumen maintenance up to 40000 Br Hrs with uniform visually comfortable light output at 150 degree beam spread, CRI minimum 80, PF should be greater than 0.95, THD <10%. Individual LED,s should not be visible for glare free output colour temperature 6500K. Make Crompton Cat No for fitting DMLN1LT8 -16 and for lamp LTT8-20 or equivalent in Havells/Phillips

S & F LED light fitting 1x9W/ 1X10W bulk head luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply , Fix and testing electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc.

Supply, laying in trenches and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all as specified and directed.

Taking down old unserviceable service connection wire of any type and size along with old and rusted house service bracket of any type and all as directed .

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of size 16 Sqmm complete all as specified and directed .

M& L for House service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified and directed .

Supply and fixing MCB DB double door TPN 4 way IP 43 IK 9 protection with sheet metal enclosure with isolated neutral bus bar DB suitable for Door earthing, insulated copper busbar assembly for mounting MCB SP / TP. Make : L&T/legrand/Havells/ABB

S & F MCB TP, 63 Amps, breaking capacity 10 KA 'C' curve confirming to IS-8828, 415 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs to be fixed in existing DB etc. Make : L&T/legrand/Havells/ABB

S & F MCB TPN, 40 Amps, breaking capacity 10 KA 'C' curve confirming to IS-8828, 415 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. Make : L&T/legrand/Havells/ABB

M & L for dry Sand cushioning in trenches for protection of cable including watering and consolidation all as specified and directed. Note: Punned thickness shall be considerd for measurment purpose

Material and labour well burnt old size sub Class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed.

m/s gaurav enterprises

M/S BUDHRAM BISHNOI

N.K. CONSTRUCTION COMPANY

SHREE GURU NANAK CONSTRUCTION COMPANY

Surya Buildcon & Engineers