ADDN/ALTN TO CERTAIN SMQs (CHURCH QTRS) PH-I AND CERTAIN MINOR WORKS AT CHAFB

Amount

COMMON ITEMS APPLICABLE FOR ALL JOBS:-

Taking down wooden chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and as directed.

Taking down wooden chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and as directed.

S&F Gun metal gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia complete all as specified and directed.

S&F Sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 2.5 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonry inc 2.5 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one length for measuring unit length.

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed. Note : All debris and rubbish shall be removed from MoD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state and local regulations

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. Note : All debris and rubbish shall be removed from MoD land during or at the end of each working period at his risk and cost in accordance with all appliacable federal, state and local regulations

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified and directed. Note : All debris and rubbish shall be removed from MoD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state and local regulations.

ITEMS APPLICABLE FOR JOB 'A':-

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, from chowkhat complete all as specified and as directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L Coloured Glazed ceramic tiles in vertical surface 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in cement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

M&L Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and directed.

M&L Machine cut Kota stone slab 20-25 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar 1:6 base including rubbing and mirror polishing, complete all as specified and directed.

M&L Machine cut Kota stone slab 20-25 mm thick (of length not less than 55 cm in skirting and 120 cm in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar 1:4 on brick work or concrete surfaces, complete all as specified.

M&L 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete all as specified and directed. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

S&F 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S&F in repairs Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

S&F in repairs Vitreous China wash basin, flat back, size 550 x 400 mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets and vitreous china pedestal complete all as specified and directed.

S&F in repairs vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified and directed.

S&F in repairs Stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast in cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified and directed.

S&F in repair stainless steel plate rack made out of 1.00mm thick sheet 900x900x200mm complete all as specified and directed.

S&F in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks complete all as specified and directed.

S&F in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed.

S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) complete all as specified and directed.

S&F in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and directed.

S&F in repair angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and directed. (Note : Weight of cock shall not be less than 0.575kg)

S&F in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified and directed.

S&F in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified and directed.

S&F in repair fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swivel joint complete all as specified and directed.

S&F in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair CP brass soap tray fixed with brass screw complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc complete all as specified and directed.

All as Sl Item no 37.00 here-in-before but 20mm bore, complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge complete all as specified and directed.

S&F GI Steel Tubes 20mm bore, 'medium grade', galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed.

Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, complete all as specified and as directed.

S&F 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cum & manufactured by "Rajshri/Echon or Techno-commercially Eqv" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dash Fasteners/Hold Fast of required dia and length, all as per specifications drawings complete all as specified and as directed. Note: Material test certificate and authentication shall be provided by the manufacturing company.

S&F 2nd class hard wood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

S&F IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

S&F Factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixing to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30 mm thick (Stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC sheet on the front page and 2 mm plane colour PVC sheet on back face supplying and fixing in frames at site as per speicfication and drawing complete all as specified and as directed. .

M&L for PCC1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast ,back of pressed steel chowkats complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

S&F in repairs double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and as directed.

S&F MS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and as directed. .

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in a square n exc 0.5 Sq m in each pane complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and as directed.

S&F in repair Galvanized mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified.

S&F Powder coated aluminium windows/ventilator/partition etc fixed/openable type or sliding without sash bar, aluminium section including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw etc complete all as specified.

S&F Anodised aluminium grill of (anodised transparent or dyed to required shade according to IS:1868 with minomum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumiinium standard section around the opening, all complete as per reuirement and direction of Engineer-in-charge complete all as specified and as directed.

S&F 4mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 75/110mm dia, with SS grating including jointing to waste pipe fixed in cement concrete type B1 1:2:4 complete all as specified and as directed.

Taking down PVC (SWR) pipes of any size incl fittings complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm dia complete all as specified and directed .

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed .

S&F stack clamps out of 40mm by 4 mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore etc complete all as specified and directed.

S&F repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 1:2:4 using 12.5mm brick aggregate complete all as specified and directed.

Supplying & laying 3 coats of Reinforced Acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in cement mortar 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed.

M&L for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform slab supported on wall, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified and directed.

M&L in repair to RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in chajjas beams etc upto tripple storey bldgs including necessary formwork complete all as specified and directed.

S&F mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in any position not other wise specifically provided for, complete all as specified and as directed. Note : All debris and rubbish shall be removed from MoD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state and local regulations

M&L PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including water proofing compound as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement complete all as specified and directed. Note: WPC (water proofing compound) shall be measured and paid separately.

M&L for 10 mm thick screed bed or bedding layer in cement mortar 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed. Note: WPC (water proofing compound) shall be measured and paid separately.

M&L for water proofing treatment on horizontal and vertical surfaces with Providing and laying / fixing TPO (Thermoplastic Polyolefin) membrane incl cleaning the surface and laying of 200 GSM Geo textile and cover up with TPO RF 1.2mm thermoplastic membrane on roof & amp, up to 300mm of parapets and crumple joint including junction of roof and parapet, welding the seam joints with hot air gun/machine and terminate the corners with extra protection to bear the high wind pressure. The TPO should be throughly tightened with the lower structure using mechanical fastening properly to avoid the corners and seam joint failure complete all as specified and directed.

S&F in repairs 18/19mm thick block board ,grade 2 quality interior grade , commercial type fixed with screw to timber frame work including taking down complete all as specified and directed.

M&L Decorative laminate type 1 of 0.9 mm thick surface finish, colour and pattern as approved, fixed with approved adhesive as manufacturer's complete all as specified and directed.

S&F Continious piano hinges, continuous type of mild steel bright finish or electro galvanized with width of flap (when open) 30mm complete all as specified and directed.

S&F 75mm long Brass handle, cast type, polished bright fixed with nut and screws to cupboard shutter complete all as specified and directed.

S&F Magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in and fixed, complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:6 on brick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering on fair faces of brick work, concrete surfaces or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified and as directed. Notes : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 m height shall be included in the quoted rate.

M&L 10 mm thick cement mortar 1:3 on ceiling, finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and directed.

M&L for preparation of new or prevously untreated plastered surfaces of walls /jallies/louvers etc and applying two coats of cement base paint , white or tinted complete all as specified and directed.

M&L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling complete all as specified and directed.

M&L for preparation of old plastered or un-plastered wall surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed.

M&L for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed.

M&L for preparation of new surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surface of any description, over 10cm in width or girth not other wise described and applying two coats of synthetic enamel paint complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings & fixtures such as switches, ceiling rose, pendants, regulators, sockets, ceiling roses,pendants, regulators, light fittings etc. Removing materials to store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down ceiling fans from ceiling, dismantaling blades & refixing of the same including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Taking down Exhaust Fans, from walls and refixing the same including connecting up and provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Taking down Geyser from walls, and handing over the same at MES store, complete all as specified and directed.

M&L Point wiring with cable of PVC insulated FRLS copper multistranded conductor 1.5 sqmm 1100 volts grade in and including medium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chasis in existing stone/ brick masonary, including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 1.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for the following :-

One light controlled by 1 switch 5 amps, single pole.

One Ceiling fan point controlled by one single pole 5 Amps switch.

One Exhaust fan point controlled by one single pole 5 Amps switch.

One 3 pin switch socket out let point 5 Amps switch on independent board.

One 3 pin switch socket out let point 5 Amps switch on same board.

One bell Point controlled by one push button 5 Amps switch on independent board.

One light controlled by two nos, 2 way switch 5 amps, single pole.

M&L Point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.50 sqmm 1100 volts grade in and including medium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chases in existing stone/ brick machinery, including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 2.50 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly complete all as specified and directed. Note : Chases/ groove cutting shall be measured and paid separately under relevant items.

S&F Piano Switch single pole one way 10 Amps complete all as specified and directed.

S&F Switch socket , 6 Amps, 2/3 pin, 240 volts Ac 2/3 pin complete all as specified and directed at site.

S&F Switch socket , 16 Amps, 2/3 pin, 240 volts Ac 2/3 pin complete all as specified and directed at site.

S&F fan regulator upto 120 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm complete all as specified and directed at site.

S&F piano type Bell push 6 A, 1 Module complete all as specified and directed at site.

S&F Ding Dong Bell, AC, 230 volts, Single Pole complete all as specified and directed at site.

S&F PVC ceiling rose 65 x 50 mm surface type with 3 terminals complete all as specified and directed at site.

S&F LED Light fitting, 36 Watts, 220 volts, LED batten type, with driver, connecting up with 2 core flexible copper conductor cable of suitable size from Ceiling rose complete all as specified and directed at site. Make : BAJAJ, Model : DELUXE LED BATTEN, CODE : 830337 or techno-commercially equivalent in HAVELLS/ CROMPTON/ ORIENT/ SURYA.

S&F LED Light fitting, 10 Watts, 220 volts, LED batten type, with driver, connecting up with 2 core flexible copper conductor cable of suitable size from Ceiling rose complete all as specified and directed at site. Make : BAJAJ, Model : IVORA LED BATTEN, CODE : 830413 or techno-commercially equivalent in HAVELLS/ CROMPTON/ ORIENT/ SURYA.

Cutting into or through the stone walls / brick walls built in cement mortar or cement lime mortar and walls of cement concrete suitable size for housing for sunk box using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed. Note : For all those items above where Chasis/ groove cutting in stone walls/ brick wall/ block masonary walls as required for concealed wiring shall be measured and paid separately under relevant item no 114.00 & 115.00.

Cutting chasis, pinning in Stone walls/ brick walls etc. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring a into or through the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

S&F Sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 6.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonry inc 6.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one length for measuring unit length.

S&F Sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 10.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealed in stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonary inc 10.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC Conduit and two run of copper conductor together taken as one length for measuring unit length.

S&F Sheet metal enclosure for VTPN DB's double door TPN 08 ways Suitable for 125 Amps MCCB Fixed in DB, deep drawn with 200 Amps rated copper bus bar 415 V, IP 43 Protection, Concealed in walls, including taking down old unsv from existing place complete all as specified and directed.

S&F Sheet metal enclosure for DB's double door SPN, 8 ways when MCBs to be used single pole and neutral,deep drawn with 200 Amps rated copper bus bar 240V, Concealed in walls including taking down old unsv from existing place complete all as specified and directed.

S&F MCB SPN, 40 Amps, 240 V, C- series with breaking capacity of 10KA complete all as specified and directed.

S&F MCB SP, 6-32 Amps, 240V, C- series with breaking capacity of 10KA complete all as specified and directed.

S&F MCCB 160 A, TP, 36 KA,415 V fixed thermal fixed magnetic setting complete all as specified and directed.

S&F LED 36 Watts building security IP 65 protection class,durable die-cast Aluminium hosuing and a shatter resistant lens complete all as specified and directed. Make : CG, Model : FREEDOM NEO, CAT NO : LSTS-36 CDL-M or equivalent in HAVELLS/ BAJAJ/ OSRAM ETC.

S&F GI Pipe 40 mm dia bend L shaped for fixing of Building security lights, including properly grouting on wall with required fixing arrangements such as bolts, nuts, screws, clamps etc complete all as specified and directed.

S&F Piano Switch single pole two way 10 Amps complete all as specified and directed.

ITEMS APPLICABLE FOR JOB 'B':-

S&F Powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coating aluminium door shutters (any type, normal or sliding), aluminium section Powder Coating (minimum thickness of powder coating 50 micron) weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc complete all as specified and directed.

S&F 12 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality, fixied with necessary glazing clips, in squares exceeding 0.5 Sqm in each panel complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F Powder coated Aluminium windows of three tracks outer frame top, side sections, bottom frame(track) with guide track of size 92.5x31x1.50mm with sliding window shutters two nos with glass and one no with wire mesh(total 3 nos shutter) frame top and side bottom section with wheel track and inner locking section of size 40X18X1.5mm inculding glass 4 mm thick and aluminium wire cloth, 0.45mm nominal dia wire and average width of aperture 1.40mm complete all as specified and directed.

S&F Powder coated Aluminium Frame work for grills Deco-grill Model DG-104(10mm) making shape and riveted with rivets and fixed with suitable channel complete necessary fixing arrangements etc complete all as specified and directed.

ITEMS APPLICABLE FOR JOB 'C':-

S&F GI Steel Tubes 25 mm bore, 'medium grade', galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed.

S&F 1000 ltrs capacity potential moulded polyethylene water storage tank (cylindrical or vertical) hoisted and fixed in position complete all as specified and directed.

S&F Ball brass valves 25 mm bore,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

ITEMS APPLICABLE FOR JOB 'D':-

M&L Addl / Altn of work station NEO 1500 x 1100 x 1200mm, by providing glass of size 51.2cm x 33cm x 8mm thickness and monitor holder steel of 6 Nos in each of good quality along with suitable screws to be fixed below the glass plain as approved by Engr-in-Charge complete all as specified and as directed. Note: Carpentry work in work station NEO 1500 x 1100 x 1200mm existing size of monitor 45cm x 33cm shall be increased to 51.2cm x 33cm.

ITEMS APPLICABLE FOR JOB 'E':-

S&F Siren electronic type horizantal single stage continuos normal operation for atleast 50 minutes with sound level 65 DB to 120 DB measured at 1.5 meter with sound output variation of +5 DB for 500 meter range complete all as specified and as directed.

S&F MCB SPN DB of 2 way for 240 volts complete all as specified and directed.

S&F MCB SPN 5 to 32 Amps 'C' Curve type 10 KA 240 Volt complete with connection and testing complete all as specified and directed.

ITEMS APPLICABLE FOR JOB 'F':-

Demolition of brick or stone/boulders masonary, built in cement mortar complete all as specified and directed.

Dismantling wall and ceiling boards ,cubboards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed.

M&L for Precast cement concrete block masonry with soild blocks, type C1 ,1:3:6 using 20mm graded aggregate exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Providing Precast cement concrete solid building blocks or slabs type C1 1:3:6 using 20mm graded aggregate 10 cm thick (with plain or interlocking joints as directed) and setting in cement mortar 1:6 complete all as specified and directed.

M&L Formwork to soffits of rough finished surface of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in cement mortar complete all as specified and directed.

M&L Formwork to edges/sides of rough finished surface of roof slab 15cm thick complete all as specified and directed.

M&L RCC (nominal mix) M-25 using 20mm graded agg Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L 100 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring or pavings etc complete all as specified and directed.

M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and tabil top for fixing wash basin and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite shade including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes incl mouding/bull nosing and polishing etc complete all as specified and directed.

M&L Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles,laid over and including cement screed bed 15 mm thick in cement mortar 1:6 laying floor finish complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surfaces 350x250x7 / 450x350x7 mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified and directed.

S&F Powder coated Aluminium windows/cupboard shutter of two tracks outer frame top, side sections, bottom frame (track) with guide track of size 92.5x31x1.50mm with sliding window shutters two nos with 5mm thick PVC plain coloured sheet frame top and side bottom section with wheel track and inner locking section of size 40X18X1.5mm inculding 3-4mm thick ACP sheet colour match with aluminium complete all as specified and directed.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surface of wall and apply three coats of white wash complete all as specified and as directed.

PRACHANIVA CONSTRUCTIONS (BID ID -3129925)

OM CONSTRUCTIONS (BID ID -3126087)

M R CONSTRUCTIONS (BID ID -3129840)