Construction of Daily market at AmbethkarNagar In north zone Thoothukudi City Municipal Corporation

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering, and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and completed depositing the surplus excavated soil with in the compound in places shown by the departmental officers with intial lead and lifts and cleaning and levelling the site etc.,complete as per TNSS

Depth of 3.2 m

Plinth Beam

Plain Cement Concrete of mix 1 : 4 : 8 (One part of Cement four part of sand eight part of aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification.

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and errecting centering for Sides and Soffits including necessary supports and strutting upto3.29mt height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90mm x60mm and 10BG stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia supported at not more than 75cm centre to centre etc complete Complying with standard Specification without Strutting

Footing and Grade Beam

COLUMN

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 3250Kg/ 10cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of M-M-Sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials) .

Basement

Ground floor

Supplying and fabrication & placing in position Steel Reinforcement using TMT rods for all RCC works as per the design given including cost of steel and binding wire etc., Complete Complying with Std Specification

Brick work in CM 1:5 (one cement & five M-Sand) using Country bricks of size 83/4"x41/4"x23/4"including finishing, curing, etc., complete complying with standard specification

Plastering in Cement Mortor 1:5 Mix (one part of Cement,, five part of sand)12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Painting the new plastered walls with two coats of Exterior emulsion paint (weather proof ) first class quality and of approved colour over a priming coat including thorough scrapping clean removal of dirt etc. complete and including necessary plaster paris putty etc. wherever required.as per (ISI STD) (It mustprovide excellent resistance against the growth of algae and fungi on the walls. And it must offer excellent protection against alkali and UV degradation and the durability period should be 5 years.

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Finish top cc pavement with power traveling machine including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Supply and fixing of M.S Grills for Windows, with one coat of Red oxide Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. including phosphating as per ISI with rust preventive primer & ready to assemble condition for easy installation at site including dismantling making necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. and Steel Door Complete as Directed by the Departmental Officer.

Painting the new iron works such as steel doors, Windows,Ventilators windows bars,balustrades etc, in all floor with two coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc, complete complying with Standard Specification. ( The Make, Quality and colour of paint should be got approved by the engineer in charge before use on works )

Fabricating, Supplying and fixing of per painted Color Galvalum iron sheets with the following specifications, the material shoud be of PPGI tile profile with a red clolour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I. base pre painted hot dipped galvanuzed iron sheet and to be fixed with shelf tappin galvanized iron sheet and to be fixed wth shelf tapping screws plastic washer. the washer and screws to be fixed by using minute power machin drilled with out damaging the sheetspaint coating to be regilar modified polyster coat with zinc coating of Z 120 GSM paint thickness the fininsh optional matt finish. The Sheet to be Fixed with making sutiable Corrugate, Cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing in position of best approved colour design and quality Polycarbonate Sheet 6mm thick with necessary 'U' or 'J' bolts, bitumen washers and cutting the sheets to the required size.etc. complete.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed FRLS SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered withhylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point (for electronic regulator) (5 points per coil)

Wiring with 2 x 1.5 sq.mm (22 / 0.3) PVC insulated FRLS SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5A 3 pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection including all cost and conveyance of material and labour charges etc complete.,

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1No 40Amp30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection

supply and fixing of 25W LED street light fitting with LED (Lower end) with 19mm dia. GI pipe (class B) with 1 no.19mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supplyandfixingof65mmdiaGIpipe(Class'B')of4metrelengthwith300mmx300mmx6mmMSbaseplatedulyweldedatthebottomandwithconcretingandconstructiononmasonarypedestalwithMSboxof30cmx20cmx10cmwithangleironframeworkwithdoorwithlockandkeyarrangementsandwithsupplyandfixingof25WLEDstreetlightfittingwithbulbandwithsupplyandfixingof16Afuseunit(500V),5ASPswitchinsidetheMSboxandpaintingwith suitable colour

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Removing and Relaying of existing interlocking Paver block high strength type conforming IS 15658-2006 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 100mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,removing sweeping tranporting loading unloading of laying paver block as per standard specification,.

Drilling 150 mm Dia bore well in allurial soil or segmentary starate using not by rig by first drilling a pilot bore of 115 mm dia direct rotary mud circulation method, using contractors rig tools fuel labour for drilling, bentonite Labour drilling at the site shown by the department officers.

Supply and delivery of unplasticised ribbed screen PVC casing pipe of the 150mm dia in 3m length with screwed and socket end and centering guide for every 15m length of pipes as per IS / 12818 / 92 and as amended from time to time to suit the borewell upto 80m depth (C.S) with ISI marking including, loading, unloading , freight, stacking and transit insurance charges etc, complete.

Supply and delivery of clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continous rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of Three Phase Panel Board - Star Delta with two level Guard and auto start (5.00 HP) suitable for Submersible pumpsets and accessories including all fittings suitable for Submersible pump sets.Panel Board should be provided as per specification. Rates inclusive of Packing, Loading, Freight, Unloading, Stacking, Transit and Insurance charges etc, complete

Supply and delivery of following 50 mm dia UPVC Column Pipe and GI Pipes and Other Special materials of good quality including cost of materials and labour with cost for coveyence to site etc Complete complying with standard Specifications. etc.,

50mm dia UPVC Column pipe

50mm UPVC . Elbow

50mm UPVC . Union

50mm UPVC Bend

50mm Gate Valve

50mm GM N.R.V

50mm PVC MTA

50mm end PVC Cap

50mm dia GI Flange set

50mm M.S. Clamp set

Labour Charges for the Erection of 50 LPM 225 mtr Head Submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TNICN switches starter, voltmeter,Ammeter, three pilot lamps capacitor single phasing preventor, water level guard and laying and jionting the cables and twin earthing as per IE rules., complete and testing the pumpset and trail run for 10 days. TWAD page No 204 WD M 0871

Supplying laying and jointing PVC Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.

32 mm dia,PVC pipe

20 mm dia,PVC pipe

32mm PVC.Elbow

32mm PVC. Bend

32mm PVC. TEE

32mm PVC. End cap

20mm PVC. Bend

20mm PVC.Elbow

20mm PVC. TEE

32mmx20mm PVC.reducer TEE

PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 AND AS AMENDED THEREAFTER 4sqmm copper cable TWAD Page No : 124 WD M 1975

Suppling and fixing in position 15mm.diameter PVC screw down tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac , thread etc.complying with standard specifications and including cutting and threading wherever necessary.

Supplying and fixing in position first quality and approved variety of 32mm Gun Metal Gate Valve (Heavy type) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements.

Supplying and fixing position PVC Nahani Trap (PVC Nahani Trap of size 100 x 75mm) with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality 110mm dia P.V.C soil/ waste pipes (6KSC)with Specials having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110 mm dia PVC pipe

110 mm dia PVC Ellbow

110 mm dia PVC Tee

Supplying and fixing of 1000 Liters capacity HDPE tank with IS specification IS 10701/96 the tank is meant for outdoor (or)indoor use complete with removable hinged top locking arrangement and to make provision to fix water supply pipe lines, necessary man hole with cover and including all PVC specials pugs, screws nails to fix the tank etc., complete and the tank should fixed firming as directed by the departmental officers. The rate shall be inclusive of all materials, labour conveyance hoisting and fixing charges etc. (The water tank should be got approved by the EE before use on work. TWAD Page no ; 87 WD M 1419

S.REX (BID ID -1383914)