GE/ALP(8219B) KOLKATA 2023-24

Amount

Taking down carefully copper/aluminium point wiring (light,fan,socket etc.) complete including fittings such as switch, ceiling rose, light fittings, regulators etc. and making good to the disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring for one light/ bell/ fan controlled by one number complete with PVC insulated unsheathed FRLSH multistranded copper conductor cable conforming to IS : 694 of size 1.5 Sqmm two runs single core for phase and neutral drawn through in and including PVC casing caping of suitable size minimum 25 mm (ISI Marked) complete with one run of FRLSH PVC insulated copper conductor cable 1.5 Sq mm single core green colour for earth continuity conductor and connecting to common earth dolly including provn of MS sheet pressed sunken box not less than 1.12 mm thick concealed on wall, with 3 mm thick laminated sheet top cover (ISI marked) for fixing of switches/socket/regulator with screws complete including making good of disturbed surfaces of wall/ceiling/floor in same specification as per existing complete all as specified and directed. Note : Proper Colour code should be maintained to identify phase, neutral & earthing.

All as per item No. 2 above but for 5 Amps Socket on same board complete all as specified and directed.

All as per item No. 2 above but for 5 Amps SSC on independent board complete all as specified and directed.

All as per item No. 2 above but for 15/16 Amps SSC with 2.5 sqmm PVC insulated copper conductor complete all as specified and directed.

M&L for point wiring for one light/ bell/ fan controlled by one number one way switch for 5 Amps SSC complete with 1100V grade FRLSH PVC insulated unsheathed multistranded copper conductor cable conforming to IS : 694 of size 1.5 Sqmm two runs single core for phase and neutral drawn through in and including PVC concealed conduit of suitable size (minimum 20mm dia medium grade ISI Marked) complete with one run of 1100V grade FRLSH PVC insulated multistranded copper conductor cable 1.5 Sq mm single core green colour for earth continuity conductor and connecting to common earth dolly including provn of modular type galvanized MS sheet pressed sunken box not less than 1.00 mm thick concealed on wall for fixing of modular cover plate of suitable modules with fixing screws, for fixing of modular type switches / socket/ Fan regulator etc. complete including making good of disturbed surfaces of wall/ceiling/floor in same specification as per existing surrounding surface complete all as specified and directed. Note : Proper colour code of wiring to be maintained.

All as per item No. 6 above but for 3 pin 6 Amps modular socket out let on the same board with 1.5 sqmm cable complete all as specified and directed.

All as per item No. 6 above but for modular socket 6 Amps controlled by 5 pin 6 Amps switch on the independent board with 1.5 sqmm cable complete all as specified and directed.

All as per item No. 6 above but for modular socket 16 Amps controlled by 5 pin 16 Amps switch on the independent board with 2.5 sqmm cable complete all as specified and directed.

Dismantling and taking down carefully sub-main wiring any size including wooden batten etc and making good the disturbed surfaces of wall/ floor to match the existing wall/ floor etc complete all as specified and directed.

Material and labour in repair/ replacement of circuit/sub-main wiring (surface type) with two runs of PVC insulated unsheathed 4.0 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 4.0 Sqmm PVC insulated & unsheathed single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade for earth continuity conductor connected to common earth dolly, drawn through PVC casing caping complete all as specified and as directed. Note : (i) Three runs of 4.0 Sqmm cable and PVC canin capin shall measured as one length.

All as per item No. 11 above but with 6 sqmm PVC insulated copper conductor complete all as specified and directed. Note : (i) Three runs of 6 Sqmm cable shall measured as one length.

Supply and fixing in replacement of 20mm dia rigid non-metallic PVC conduit (Medium duty) exclusive of boxes (Junction of terminal) but inclusive of all tees, bends, bows, reducers, bell mount tube ends and fixing accessories such as couplers, lock nuts, saddles pipe hooks etc complete all as specified and directed.

All as per ser item No 13 here-in-before but 25mm dia

Supply and fix in replacement of 25mm size PVC casing caping 2mm thick complete with all accessories complete all as specified and directed.

Supply and fix in replacement 20mm dia PVC Flexible conduit complete all as specified and as directed by the Engr-in-Chrage.

Supply and fix in replacement PVC junction box suitable for 20mm dia conduit complete all as specified and directed.

All as per ser item No 17 here-in-before but 25mm dia

Supply and fix in repair MS box made of 1.6mm thick MS sheet painted with smoke grey paint on all sides after dismantling old one including making good the disturbed surfaces complete all as specified and directed of the following sizes :-

25cm x 20 cm x 6 cm

15cm x 10cm x 6 cm

10cm x 10cm x 4 cm

Supply and fix in repair ceiling rose, 3 terminal, PVC/ polycarbonate isolated body, 6 Amps, 230 V complete all as specified and directed.

Supply and fix in repair Piano switch flush type single pole one way 5 Amps, 230 V complete all as specified and directed

Supply and fix in repair switch socket combination flush type, 2 in 1 multipurpose, 5 Pin, 5 Amps and 15 Amps controlled by one switch, (ISI marked) complete all as specified and directed.

Supply and fix in repair switch socket combination, 2 in 1, 5 pin, 15 Amp flush type (ISI Marked) complete all as specified and directed.

Supply and fix in repair Call bell musical door chrome AC 230 volts single pole with 2 Nos AA Battery including bell push, flush type, 5 amp complete all as specified and directed

Supply and fix in repair batten holder PVC / Poly carbonate with black plate suitable for batten complete all as specified and directed

Supply and fix in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed.

M&L for modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

M&L for modular type socket 5 pin, 6 Amps combined 2 module complete all as specified and directd.

M&L for Modular type socket 5 pin, 16 Amps combined 2 module complete all as specified and directed.

M&L for Modular type switch, one way 16 Amps, 1 module complete all as specified and directed

M&L for Modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

M&L for modular white cover plate with frame 2 module including taking down of old one complete all as specified and directed.

M&L for modular white cover plate with frame 3 module including taking down of old one complete all as specified and directed.

M&L for modular white cover plate with frame 6 module including taking down of old one complete all as specified and directed.

M&L for modular white cover plate with frame 8 module including taking down of old one complete all as specified and directed.

M&L for modular white cover plate with frame 12 module including taking down of old one complete all as specified and directed.

M&L for modular metal flush box 1 / 2 module including taking down of old one complete all as specified and directd.

M&L for modular metal flush box 3 module including taking down of old one complete all as specified and directd.

M&L for modular metal flush box 6 module including taking down of old onecomplete all as specified and directed.

Supply and fixing for modular Metal flush box 8 module complete all as specified and as directed. Make - Legrand Cat no. 6890 42 or equivalent make

M&L for modular white cover plate with frame 12 module including taking down of old one complete all as specified and directed. Make:-Legrand Cat no. 6890 42 or equivalent make approved by GE.

S&F in reair 2.15/3.15 mfd fan capacitor suitable for 1200mm ceiling fan complete all as specified and directed. Make : Havells/Tibcon/EPCOS or equivalent make approved by GE.

Supply and fix for 3mm thick industrial plastic laminated sheet duly cut for fixing switch piano type, switch socket combination etc of the following size complete all as specified and directed. Make : Super hylem or equivalent approved make approved by GE.

11" x 9 " Sheet

7" x 5" Sheet

5" x 5" Sheet

Supply and fixing as in repair MCB 06 Amps to 32 Amps, single pole, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T.

Supply and fixing as in repair MCB 40 Amps to 63 Amps, single pole, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T.

Supply and fixing as in repair MCB 06 Amps to 32 Amps, SPN, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T.

Supply and fixing in repair MCB 40 Amps to 63 Amps, SPN, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T.

Supply and fix as in repair SPN MCB DB 8 way with 200 Amps rated bus bar, neutral link, dinrail suitable for mounting MCB's 240 volts double door type including taking down old one and making good the disturbed surface complete all as specified and as directed. Make : C&S /Legrand/ Havells/L&T.

Supply and fix as in repair SPN MCB DB 4 way with 200 Amps rated bus bar, neutral link, dinrail suitable for mounting MCB's 240 volts double door type busbar for distribution of power and light circuit including taking down old bus bar box and making good the disturbed surface complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T

Supply and fix as in repair SPN MCB DB 2 way suitable for mounting MCB's 240 volts single door type including taking down old one and making good the disturbed surface complete all as specified and directed. Make : C&S /Legrand/ Havells/L&T

Dressing/rearranging of electric wiring in casing caping/PVC conduit pipes by replacing fixing screws, saddles , wooden gutties etc as per site requirement and complete all as specified and directed.

Supply and fixing in repair for AC power supply unit 6 module consisting of in built starter, plug top, isolator and box on surfacemounted or flushmounted complete all as specified and as directed by the Engr-in-Charge. Make : North West, Model ACPU 6 M-BT of Havells or equivalent as approved by GE.

S&F in repair LED tube light fitting 4 ft 20 watt, Neutral white 230 volt energy efficient comprises of extruded aluminum housing, with inbuilt driver and PC diffuser including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.all as specified and directed. Make:- Havells (Cat No ENDURALINEARNEOBS20WLED865PCHW)/ Bajaj (Cat No BCLAB20W WH)/Cromption cat No-CCS-103-20-65-SL-DP-NWH

All as per item No 53 above but LED tube light of warm White LED complete all as specified and directed. Make :-Havells/Crompton/BAJAJ/Philips

Supply and fixing for LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with inbuilt driver and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make : - Crompton (Cat No CCS-103-10-65-SL-DP-NWH) Havells : Cat No LUMILINEBS10WLED865SPCWH) Bajaj : Cat No BCLSB 10WWH)

Supply and fixing for LED strip light in cover 25W, CCT 400K, IP 65, having efficacy 100 lm/W , 220 V AC decorative type with inbuilt driver and LED lamp including electical connection complete all as specified and as directed by the Engr-in-Charge. Make : /HAVELLS Cat No FLEXISTRIP25MIP2024V/1ALED830MOD V1/BAJAJ Cat No BPLS25WLEDSTRIP IP20 NW or Havells

Supply and fixing recessed type LED spot light 09/12W, warm white, IP 20, having efficacy 100 lm/W , 220 V AC with inbuilt driver and LED lamp including electical connection complete all as specified and directed. Make : Bajaj Cat No BGSBL9WLEDWW or equivalent in make CROMPTON

Supply and fixing recessed type LED round ceiling light 18/21W, warm white, IP 20, having efficacy 100 lm/W , 220 V AC with inbuilt driver and LED lamp including electical connection complete all as specified and directed. Make : CROMPTON cat No LCDRC-18-CDL or /HAVELLS Cat No ENDURAHODLR21WLED857MO or /BAJAJ Cat No BGSLO Sleek Recess RD 18W WH LED

Supply and fixing recessed type LED round ceiling light 15W, warm white, IP 20, having efficacy 100 lm/W , 220 V AC with inbuilt driver and LED lamp including electical connection complete all as specified and directed. Make : CROMPTON cat No LCDRC-15-CDL or HAVELLS Cat No ENDURAHODLR15WLED857MOD or BAJAJ Cat No BGSLO Sleek Recess RD 15W WH LED

Supply and fixing recessed type LED round ceiling light 12W, warm white, IP 20, having efficacy 100 lm/W , 220 V AC with inbuilt driver and LED lamp including electical connection complete all as specified and directed. Make : CROMPTON cat No LCDRC-12-CDL or HAVELLS Cat No ENDURAHODLR12WLED857MOD or BAJAJ Cat No BGSLO Sleek Recess RD 12W WH LED

S&F in repair recess mounted 2'x2' luminaire with white powder coated CRCA housing having LED 36W cool day light IP-20, lumen efficiency not less than 100 lumen/watt, 220V , AC with inbuilt driver and led lamp including electrical connection complete all as specified and directed. Make : CROMPTON cat No LCTLRNM-36-FO-CDL or HAVELLS Cat No VENUSNEO2X2PLR36WLED865PO or BAJAJ Cat No BZRSQL36W LED GXWH

Taking down ceiling fan of any type, any make and any sweep for repairing, opening the body and blade, checking for repalcement of unserviceable spares,cleaning, overoiling, greasing, replacement of unserviceable spare by new one, re-assembling of all components in original position, testing and hanging up the same complete all as specified and directed. Note : New spare parts required for replacement shall be measured and paid seperately.

Supply only MS split pin size 2 " x 1/8 " for ceiling fan of 1200/1400mm sweep complete all as specified and directed.

Supply only hanging bolt with nut of size 3/8" x 3 1/2 " for ceiling fan of 1200/1400mm Sweep complete all as specified and directed. (Make : Tata/Jindal)

Supply only rubber bush of size 1 1/2 " dia x 1" thick for ceiling fan of 1200/1400mm sweep complete all as specified and directed.

Supply only Ball bearing of size 6201/6202/6203 for ceiling fan of 1200/1400mm sweep complete all as specified and directed. Make : (TATA/SKF).

Supply only Metal bush bearing for ceiling fan of 1200/1400mm sweep complete all as specified and directed.(Make : TATA/SKF).

Taking down exhaust fan of any type, any make and any sweep for repairing, opening the body including blade, checking for repalcement of unserviceable spares,cleaning, oiling, greasing including replacement of unserviceable spare by new one, painting, re-assembling of all components in original position, testing and hanging up the same complete all as specified and directed. Note : New spare parts required for replacement shall be measured and paid seperately as 'Supply only"

Supply only ball bearing 2001/ 2002/ 2003 for exhaust fans complete all as specified and directed. Make : TATA/SKF

Supply only metal bush bearing for exhaust fans complete all as specified and as directed. Make : TATA/SKF

Supply and fixing as in repair 2.5 mfd capacitor complete all as specified and directed.

All as per item No 71 above but 3.5 mfd capacity complete all as specified and directed.

Taking down cabin fan/wall mounted fan of any type, any make , by opening of body carefully checking for repalcement of unserviceable spares, including replacement of spares by new one, re-assembling of all components in original position, cleaning, oiling greasing, testing and fixed in original position complete all as specified and directed. Note : New spare parts required for replacement shall be measured and paid seperately as 'Supply only"

Supply only ball bearing size 2601 quality for cabin fan/wall mounted fan complete all as specified and directed. (Make : TATA/SKF).

Supply only Metal bush bearing for cabin fan/wall mounted fan complete all as specified and directed. (Make : TATA/SKF).

Material and labour for painting of ceiling fan of size 1200mm sweep with down rod upto 2.00 mtr long with two coats of synthetic enamel white paint including preparation old painted surface including writing of MES No with letters n,exc 15cm height complete all as specified and directed.

All as per item No 76 above but 1400mm sweep complete all as specified and directed.

Supply and fixing as in repair for MS clamps made out of 50x6mm flat iron suitable for hanging of ceiling fan on pipe including necessary cutting, threading, drilling fixing arrangement split pin, nuts bolts washer etc complete all as specified and directed.

Supply and fixing as in repair for ceiling fan hanging clamp made of MS rod bent to 'S' shape complete all as specified and as directed.

Rewinding of ceiling fan, 1200mm sweep with synthetic enamel copper wire including insulation of starter with polyster paper/manllex paper with cotontak binding, heat varnished and complete all as specified and directed.

All as per item No 80 above but for 1400mm sweep complete all as specified and directed.

All as per item No 80 above but for exhaust fan of 230mm sweep complete all as specified and directed.

All as per item No 80 above but for exhaust fan of sweep exc 230mm but n exc 450mm complete all as specified and directed.

All as per item No 80 above but for wall/cabin fan of any sweep complete all as specified and directed

Supply and fixing as in repair M.S. galvanised louvers suitable for exhust fan of size 300/230mm sweep complete all as specified and directed.

Shifting only ceiling fan from one position to another and hanging including provision of PVC insulated unsheathed flexible copper cable 1.5 sqmm (FRLSH) from ceiling rose to fan complete all as specified and directed.

Taking down geyser and scraping, cleaning including brazing of inner vessel of the geyser at leakage point to made it leak proof including testing pressure and assembling of all component refixing complete for 25 Ltr capacity complete all as specified and directed.

All as per item No 87 above but for 50 Ltr capacity complete all as specified and directed.

Supply and fixing as in repair for heating elements of 1.5/2 KW 230 V suitable for water heater of any type including connection with suitable cable complete all as specified and directed.

Supply and fixing as in repair suitable for five star rating, special heating elements of 2 KW 230 V suitable for water heater of any type including connection with suitable cable complete all as specified and directed.

Supply and fixing as in repair for thermostat switch of geyser 230 V, 30 degree to 90 degree centigrade temp range to be set at 70 degree to 50 degree centi grade suitable for water heater complete all as specified and directed.

Supply and fixing as in repair for bottom cover, made out of MS sheet 16 guage, duly painted with two coats of white synthetic enamel paint both side over a coat of red oxide zinc chrome primer for 25 Ltr capacity geyser complete all as specified and directed.

All as per item No 92 here-in-before but for 50 Ltr capacity complete all as specified and directed.

Supply and fixing as in repair for top cover made out of MS sheet 16 guage, duly painted with two coats of white synthetic enamel paint both side over a coat of red oxide zinc chrome primer of 25 Ltr capacity geyser complete all as specified and directed.

All as per item No 94 here-in-before but for 50 Ltr capacity complete all as specified and directed.

Supply and fixing as in repair for MS flange for geyser of 25/50 ltr capicity complete all as specified and directed.

Supply and fixing as in repair for split cover made out of 16 guage sheet duly painted with synthetic enamel paint suitable for water heater of 25 ltr capacity complete all as specified and directed.

All as per item No 97 above but for 50 ltr capacity complete all as specified and directed.

Supply and fixing as in repair for indicating lamp, 230 V, flush type, rectangular, red indicator suitalbe for water heaters complete all as specified and directed.

Supply and fixing as in repair for 450mm long connection pipe (Hot water for geyser) with 2 nuts complete all as specified and directed.

Supply and fixing as in repair for PVC inlet connector pipe 450mm long for geyser, heavy duty, with brass coupling both ends to fix inlet of geyser complete all as specified and as directed. Make : Prayag/Polytuf

Supply and fixing as in repair for apparatus plate , asembly suitable for water storage heater of 25 ltrs capacity complete all as specified and directed.

All as per item No 102 above but for 50 Ltr capacity complete all as specified and directed.

Supply and fixing as in repair for glass wool, between the inner and outer vessel of water heater any type and capacity complete all as specified and directed.

Supply and fixing for copper inner tank of 25 ltr capacity geyser of heavy guage to withstand pressure upto 8 bars including testing pressure and taking down of old unserviceable one complete all as specified and directed.

All as per item No. 105 above but of capcity 50 Ltrs.

Supply and fixing as in repair for PVC insulated sheathed round flexible copper conductor cable 2.50 Sqmm 3 core , 1100 Volts grade conforming to IS 694 (FRLSH) complete all as specified and directed.

Supply and fixing as in repair split type bolt MS 12mm dia, 10cm long grouted with cement mortar suitable for fixing new geyser including making good to distrubed surface complete all as specified and directed.

Material and labour for preparation to old painted surface of storage water heater of 25 ltr capacity and painting with two coats of synthetic enamel paint (white) by using spray gun complete all as specified and as directed.

All as per item No 109 before but for 50 Ltr capacity complete all as specified and directed.

Supply and fixing as in repair for 16 amp, 3 pin plug top complete all as specified and directed.

Dismantling of old unserviceable Panel and Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1500 mm Height (Without Canopy & Base Channel) 1200 mm width x 500 mm Depth, M.S. Channel base frame mounted (to be mounted on the 3 side covered brick / PCC. pedestal of height 600 mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos aluminium bus bars of rating 400 amps, Provision of Spreader link to both incoming and outgoing side of MCCBs for termination of cables. The Feeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting with approved shade of RAL 7032 (SIEMENS GRAY). The feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-54 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.15mm thick CRCA stainless steel sheet for outer shell & canopy and 2.0mm thick for inner doors / partations and 3.15mm thick gland plate and having compartmentalized construction for individual switchgears and bus bars and having front opening facility with double layer shutter and rear opening facility with single layer shutter with locking facility and 4 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :- Location : Near P-1 building of JCO's MD accn

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided from the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos aluminium bus bars of rating 400amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size 1100 volt grade PVC insulated copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 50mm x 6 mm. CONTROL WIRING :- All control wirings shall have to be carried out with 1100 volts rated FRLSH grade PVC insulated (Gray Colour) multi-flexible type copper wire of cross sectional area 1.50 Sq mm and shall be properly bunched,tied and dressed, ferrule marked for proper identification and crimped with suitable size & type of tinned copper lugs and shall be wrapped with PVC spring type flexible pipes near the door hinges. INCOMING :- (i) Onload change over switch 250A, 4 pole, 415 Volt-01 No (Make - Havells/L&T/Legrand) OUTGOINGS :- MCCB 250Amps (36 KA) 4 Pole Adjustabble thermal (80% to 100%) and fixed magnetic protection and with rotary handle - 02 Nos (One is standby)

Note : (1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. (2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. (3) All the inner / outer doors should have locking facility through castle locks (4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. (5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. (6)The thickness of MS Sheet for outer shell and canopy shall be of 3.15mm and inner doors and partitions shall be of 2.0 mm (7) The Panel board should be designed in such a way that adequete workable space is made available inside every compartments. (8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process. (9) Dismantling of LT Energy Meters from its existing location and refixing of those meters in new location shall be carried out by MES / CESC at their own arrangement.

Disconnection and taking out old unserviceable energy meter, any rating and type, from its existing position and keeping aside for disposal all as specified and directed.

S&F for Single phase tamper Proof electronic energy Meter (05-30 Amps) with LCD display, accuracy class 1%,suitable for 230 volts AC 50 Hz supply. (Make : L&T/ HPL / SECURE)

S&F in repair digital ammeter 0-250A capacity complete all as specified and directed. (Make : AE/ L&T /RISHABH)

S&F in repair digital Voltmeter 415V capacity complete all as specified and directed. (Make : AE/ L&T /RISHABH)

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm buried directly in ground, earth pit not less than 2.25 mtrs deep below ground level, with top edge of the plate at a depth of not less than 1.5 mtrs below ground level connected to galvanized earth strip 32x6mm dia as earthing lead by means of GI bolts, nuts and washers upto 7.5 meters length from earth chamber / fit etc all as shown in electrical plate No.3 of MES SSR Part-I and connecting to earthing test point including necessary excavation and earth work in any type of soil, returning, filling in and disposal of surplus soil to a distance exceeding 50mtrs, PCC (1:3:6) type C1 (using 20mm graded stone aggregate) earth pit, 40mm thick RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) cover with suitable reinforcement, watering arrangement, funnel etc complete all as specified and directed.

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion.

Supply and fixing for 12mm dia, 300mm long, single pointed air termination aluminium rod including taking down of existing one and making good the disturbed surfaces complete all as specified and directed.

Supply and fixing for single aluminium strip of size 25 x3.15 mm in proper position with saddles and fixing screws for roof conductors and down conductors from top of the building air termination point to the test point of the building of height G+3 as required after and including taking down of the old unserviceable one and making good the disturbed surface complete all as specified and directed.

Material and labour as in replacement earth continuity conductor or main earthing strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed with poles or any other indicated sitution for loop earthing etc as required using galvanised iron strip of size 32 X 6 mm complete all as specified and directed.

Material and labour for test point terminal block made of gun metal or phosphorus bronze of size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw after and including dismantling of existing unserviceable one complete all as specified and directed.

Supply and fixing for 40mm bore steel tubes "light grade" galvanized with all fittings and fixed to wall after and including taking up or down existing unserviceable GI Pipe complete all as specified and directed.

S&F for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25X4 mm galvanised iron strip.

S&F for M.S Plate of size 300x300x2.00 mm dully mentioning date of testing and testing result for earth Pit, Painted with synthtic enameld paint of black colour, dualy fixed on PCC coping (1:2:4) and all as directed.

M&L for electricain + Helper with earth testing equipment for testing of earth pit after opening the strip from the test point and for Watering the earthing pit complete as specified all and directed.

Material and labour for replacement of 80/100 mfd 415 V Starting capacitor forAC/ water cooler. (Make : Sarda/Universal/Tibcon)

Material and labour for replacement running capacitor 10 mfd for Water Cooler of capacity 80/ 150 ltrs. (Make : sarda/universal/tibcon)

Material and labour for replacement of 15mm bore chromium plated push cock suitable for water cooler of any capacity as per existing specification.

Material and labour for replacement of thermostat switch for water cooler. (Make : Indfoss /Danfoss/Ranutrol)

Material and labour for replacement of PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 15 mm complete all as specified and directed.

Disconnecting defective sealed compressor unit of Water cooler 80/ 150 ltrs capacity from the water cooler and fixing of new compressor of same specification in original position all as specified and directed. Make- Kirloskar/SPIRAM/Tecumsh

Material and labour for door gasket for 150 ltrs capacity Water Cooler

Material and labour for door gasket for 80 ltrs capacity Water Cooler

Material and labour for starting Relay suitable for water cooler 80/ 150 ltrs capacity (Make- Ranutrol/Elkay/Real Life/Uxcell)

Material and labour for replacement of overload protector suitable for Water Cooler of capacity 150 ltrs

Material and labour for replacement as in repair of overload protector suitable for water cooler of capacity 80 ltrs

Material and labour for replacement of starting relay box type for refrigerators of capacity upto 315 ltrs. (Make- Ranutrol/Elkay/Whirlpool/Uxcell)

Material and labour for replacement of copper capillary tube of size 0.36 mm for refrigerators of capacity upto 315 ltrs.

Material and labour for replacement of cooling coil for refrigerators of capacity upto 315 ltrs.

Material and labour for freezer door for refrigerators of capacity upto 315 ltrs complete all as specified and directed.

Material and labour for replacement of thermostat switch for Refrigerators of capacity upto 315 ltrs. (Make- Ranutrol/Indfoss/Kelvinator)

Material and labour for Chill tray for refrigerators of capacity upto 315 ltrs.

Disconnecting defective condenser coil of refrigerators upto 315 ltrs capacity and replacing the same with new condenser coil and fixing in original position as per existing specification and size complete all as specified and directed.

Material and labour for inner lights filament type/LED as per existing one for refrigerators of capacity upto 315 ltrs

Disconnecting defective sealed compressor unit of refrigerators upto 315 ltrs capacity and fixing new hermitcially sealed compressor unit of same specificationas fixed in original position all as specified and directed.

Material and labour for door switch for refrigerators of capacity upto 315 ltrs

Material and labour for replacement of 5 Amps 3 pin 230 Volts Plug Top Make : Anchor/Havells/Standard

Material and labour for servicing by dismantling the cover of Condensor and cooling coil, thoroughly cleaning the external surface (both side) of all the component including fins, base , discaling chemicals, water etc with the help of air blower, wire brushing water jet pump etc and reassemble all the components plate, runner, fan blade etc in original position as and when directed for following capacity of Air Conditioners: -

Split type Air Conditioner of capacity 1.5 TR

Split type Air Conditioner of capacity 2.0 TR

Material and labour for repair of AC single phase 230 volt Printed Circuit Board for 1.5/ 2.0 TR capacity split type AC cooling unit of carrier/Voltas/LG/Amtex complete all as specified and as directed.

M&L for replacement of AC single phase 230 volts remote control unit (Hand set) for 1.5/ 2.0 TR capacity for split type AC complete all as specified and directed.

Re-winding blower motor, including replacement of bushes, with same size and gauge of super enamelled copper wire for Split type AC 1.5 TR capacity (Condensing unit) complete all as specified and directed.

Re-winding Blower motor including replacement of bushes with same size and gauge of wire for split type AC 2.0 TR capacity (Condensing unit) complete all as specified and as directed.

Material and labour for replacement of 6 mfd capacitor for blower moter of AC of any capacity. Make: Sarda/ Universal/Tibcon motor

Material and labour for replacment of 36 mfd running capacitor of any capacity. Make: Sarda/ Universal/Tibcon motor

Material and labour for replacment of 40 mfd running capacitor of any capacity. Make: Sarda/ Universal/Tibcon motor

Material and labour for replacment of 50 mfd running capacitor of any capacity. Make : Make: Sarda/ Universal/Tibcon motor

Material and labour for replacement of thermostat switch for 1.5 TR capacity window Type AC complete all as specified and directed. Make: Danfos/Indfos/Ranutrol

Material and labour for fan blade for 1.5 TR capacity Window type AC complete all as specified and directed.

Material and labour for replacement of over load protector for Window/ Split Type AC of capacity 1.5 TR complete all as specified and directed.

Supply and fixing of rotary type compressor for window/ Split type AC of capacity 1.5 TR complete all as specified and as directed.

M & L for Cleaning the cooling coil and condensor with the help of compressed Nitrogen gas passing through in side of the copper tube for flushing out all sludge and oil deposited in the copper tube and materials and labour for charging of refrigerant as required including replacement of strainer and finding out the leakage, brushing the same, testing for window/Split AC of 1.5/2.0 TR complete all as specified and directed.

Material and Labour for disconnecting defective indoor unit of split AC capacity 2 TR and replacing the same with new indoor unit in position fixing in original position as per existing and compaitable to Acs of complete all as specified and directed.

Material and Labour for disconnecting defective outdoor unit of split AC capacity 2 TR and replacing the same with new outdoor unit (incl new compressor and other accessories) in position fixing in original position as per existing and compaitable to Acs complete all as specified and directed.

Material and Labour for disconnecting defective indoor unit of split AC capacity 1.5 TR and replacing the same with new indoor unit in position fixing in original position as per existing and compaitable to Acs of complete all as specified and directed.

Material and Labour for disconnecting defective outdoor unit of split AC capacity 1.5 TR and replacing the same with new outdoor unit (incl new compressor and other accessories) in position fixing in original position as per existing and compaitable to Acs of Make- Godrej/Voltas/LG/Amtex/Haier complete all as specified and as directed.

Material and labour for charging of Refrigerant of suitable type (CFCbased/Non CFC Based) in Split/ Window AC, Water Cooler and Refrigerator complete all as specified and directed.

Supply and fix in repair sedimentation filter cartridge for Kent RO capacity of 25 ltrs/hr complete all as specified and directed.

Supply and fix in repair booster pumps for Kent RO capacity of 25 ltrs/hr complete all as specified and directed.

Supply and fix in repair adaptors for Kent RO capacity of 25ltrs/hr complete all as specified and directed.

Supply and fix in repair SMPS for Kent RO capacity of 25 ltrs/hr complete all as specified and directed.

Supply and fix in repair Activated carbon block filter membrane for Kent RO capacity of 25 ltrs/hrs complete all as specified and directed.

Supply and fix in repair UF & Post carbon filter cartridge for Kent RO capacity of 25 ltrs/hrs, complete all as specified and directed.

Supply and fix in repair water pump for RO plant capacity of 25 ltrs/hrs, complete all as specified and directed.

Material and labour for preparation of old treated surfaces of wall by brooming down or steel wire brushing and applying one coat of white washing on wall surface etc complete all as specified and directed.

All as per item No 175 here-in-before but on ceiling.

Material and labour for Preparation of old plastered surfaces and applying two coats of white wash on walls complete all as specified and directed.

Material and labour for Preparation of old plastered surfaces and applying one coat of acrylic washable distemper on walls complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces wall and applying two coats of acrylic washable distemper in wall complete all as specified and as directed by the Engr-in-Charge

Material and labour for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint on steel surface complete all as specified and directed.

M&L for 2 mm thick wall care putty on wall and ceiling surfaces as required (in two layers) etc complete all as specified and directed by Engineer-in-charge. (upto 12 storey High of building)

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc.complete all as specified and directed.

Materials and labour for 15 mm thick rendering on fair faces of brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Material and labour for 5mm thick rendering in cement mortar (1:3) on concrete surface as in ceiling and finished the surface even and smooth without using extra cement complete all as specified and directed.

Material & labour for preparation of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds,etc and applying one coat of anti-algae and anti-fungal exterior grade weather coat paint (upto 12 storey bldg) complete all as specified and directed.

Materials and labour for Preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling surface etc complete all as specified and directed.

Material & labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distember over a coat of primer (upto 12 storey bldg) complete all as specified and directed.

Materials and labour for Preparation of new plastered surfaces of walls and applying three coats of white wash on wall surface etc complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) and removing debris and rubbish off the premises.

M&L for non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, infloors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including screed bed or bedding layer 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed.(upto 12 storey High of building)

All as per item No 191 above but as in skirting over and including backing coat of mortar 10 mm thick in cement mortar (1:4) as in dado/skirting complete all as specified and directed. (upto12 storey of building)

Material and labour for colour printed glazed ceramic tiles (Premium quality) (450mmX300mm) X 7mm thick as in walls set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including 10 mm thick cement plaster in CM (1 : 4) complete all as specified and directed.

Material and labour for double charged vitrified coloured tiles (Premium Quality) of size (600mmx600mm) x 8-9mm thick in floor, etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including 15 mm thick screed bed in CM (1 : 6 ) for laying of floor finishes complete all as specified and directed.

All as per item No 194 here-in-before but fixed on vertical surface as on skirting including 10mm thick cement plaster in cement mortar (1:4).

Taking down chowkhat or frames with shutter not exc. 1.5 Sqm each (without taking of shutters from the frames) complete all as specified and directed by.

S&F for solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube in opening all as shown on drawing and specification (upto 12 storied bldg) .

S&F for factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing. (upto 12 storied bldg).

Supply and fixing in repair powder coated aluminum ventilator (single leaf single shutter) side hung type with stainless steel butt hinges, one shutter glazed with and including 4.00mm thick plain sheet glass and other shutter with stainless steel wire cloth of 0.36 mm dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples, rubber gasket, stopper,aluminium anodised handle 100mm long ,aluminium anodised tower bolts 100mm long and peg stay etc, size of aluminum frame shall be 100mmx50mmx1.50mm and shutter frame shall be 40mmx20mmx1.50mm complete all as specified and directed. upto 12 storied bldg Note : 1 No Glazed shutter and 1 No Gauged shutter constitube one unit.

Supply and fixing for 75mm size stainless steel butt hinges medium weight, cold rolled complete all as specified and directed.

Supply and fixing for 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F for 150mm long aluminium,anodised extruded handle fabricated type, complete all as specified and as directed

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal.

M&L for cutting chases, pinning, in making good to facing where required of of brick wall and pointing in cement motrar 1:3 to ends and cutting chases for concealed water tubing and concealed conduit wiring ete and making good surfaces

Supplying and laying for 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls including all brass fitting/fixtures in any grade to receive plumbing fittings and fixtures complete all as specified and directed

Supply and fixing as in repair spindle for 15 mm bore bib cock / stop cock / pillar tap complete all as specified and directed.

Supply and fixing as in repair brass CP knob for 15mm dia bib cock/pillar cock concealed stop cock complete all as specified and directed.

Supply and fixing as in repair 15mm dia PVC connection pipe 600mm long with PTMT nuts complete all as specified and directed.

S&F in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, white colour, low level, white with inlet, ball valve, float and handle including brackets duly painted, 32mm dia PVC flush pipe complete all as specified and directed. (upto 12 storey High of building).

Supply and fixing as in repair 32 mm dia PVC flush pipe of polyethylene of low or high density for low level cistern/kitchen sink/WHB complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all specified and directed. (upto 4 storey bldg)

S&F in repair PVC water closet seat cover heavy duty coloured closed pattern with flat bottom and cover and mild steel CP hinnging device complete.

S&F in repairs Vitreous China wash basin ( white), flat back, size 580 x 450 mm, excluding taps, waste,chain and plug and porcelain stopper but including brackets, complete all as specified and directed.(upto 12 storey High of building)

S&F in repairs, vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete.

S & F in repair vitreous china squatting pan of orissa pattern long pan of size 580 mm x 440mm with integral foot rest white with cast iron p or s trap with back inlet including flush pipe of suitable length to connection with existing cistern & make good complete all as specified and as directed by Engineer-in-Charge.(upto12 storey high of building)

S&F in repair 15mm bore brass CP bib cock fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and complete all as specified and directed.(upto 12 storey high of building)

Supply and fixing in repair concealed 15 mm bore CP stop cock with sliding flange 15 mm complete all as specified and directed.

Supply and fix in repair pillar taps made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified and directed.

Supply & fix in repair angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified and directed.

S&F in repair for 100 mm dia cast iron floor traps with steel grating jointing to waste pipe fixed in cement concrete Type B0 (1:2:4) using 12.50mm graded stone aggregrate

Demolition of brick work built in cement mortar including all quions, arches, pillers etc complete all as specified and directed.

Material and Labour for brick work with sub class 'B' brick straight of curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

Material and Labour for brick work with sub class B bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and directed.

DILIP CONSTRUCTION

PUTUL CONSTRUCTION CO.

GAYATRI ENTERPRISE

Shanti Construction Company

M. M. C. AND CO

RADHA ENTERPRISE

NUPUR CONSTRUCTION