SPL REPAIR WORK TO BLDG NO P35 (OFFR MD ACCN) AND SPL REPAIR WORK TO BLDG NO MES17 (OR MD ACCN) AT MIL STN JAMSHEDPUR UNDER GE RANCHI

Amount

Demolition of plain cement concrete in ground floor and paving not exceeding 15cm thickness below or above ground level including removal of same to exceeding 1 Km but not exceeding 1.5 Km complete all as specified and directed.

M&L for PCC (1:5:10) type E-2 using 40mm graded brick aggregate as in sunken portion complete all as directed at site.

M&L PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in sunken floor .average thickness 40mm and making adequate slop towards spout pipe etc complete all as directed at site.

Demolition of plain cement concrete Concrete of any description and in any position not otherwise specifically provided for including removal of same to exceeding 1 Km but not exceeding 1.5 Km complete all as specified and directed.

M&L for PCC (1:4:8) Cement concrete type D-2 using 40mm graded stone aggregate in foundations,filling and mass concrete

M&L for Cement concrete type B- 2,1:2:4 ,75mm thick (40mm graded aggregate) as in floors.

Taking down cement plaster on brick wall or concrete surface etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:6) on wall finishing the surfaces even and smooth without using extra cement.

M&L for rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:4) with using on wall finishing the surfaces even and fair without using extra cement.

M&L for 10 mm thick cement plaster in cement mortar 1:3 for ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Supply and fix for Three Track Sliding powder coated aluminium Window of sizes of Top/Side and Bottom track section of 91.80mm x 31.75mm x 1.20mm thick and Shutter section of sizes 39.40 mm x 17.70mm x 1.20mm thick including joining cleats, beading,locking arrangement, rubber gasket for fixing etc complete with 5.5 mm thick tinted glass & stailness steel wire cloth, 0.36 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete .

Supply and fix forAnodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazingclips, rubber packing, anodisedaluminium snap beading, screwsetc. complete all as specified.

S&F frame work such as grills, grating etc with ends of bars shouldered and or rivetted or forged into spikes, framed guard bars, barred iron doors, ladders etc and similar wks conforming to Fe-290 Gd E-165 .

Taking down chowkhats or frame n.exc 1.50 Sqm each with shutter (without taking of shutter from framed) complete incl removing from site.

Taking down chowkhats or frame exc 1.50 Sqm but n.exc 4 Sqm each with shutter (without taking of shutter from framed) complete incl removing from site.

Taking down shutters of any description exc 1 sqm and n. exc 2 sq m each and removing from site.

M&L Pressed steel frames 125 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L Pressed steel frames 105 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L for 30 mm thick flush shutters solid core construction,with block board core and ply wood face panels, commercial type on both sides including 1mm thick wood grain printed pvc sheet fixed or laid on to flush door by using rubber based adhesive at site as per specification as per SSR Part-1 complete as specified and directed.

S&F 30mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube S&F in opening all as shown on drawing and specified.

S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed to gather with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or stainless steel wire staples

S&F Hasp and staple safety type aluminium anodized hinges pin incl bolt to hinges plate 125 mm long.

S&F butt hinges 100mm long medium weight cold rolled MS and fixed complete all as directed at site.

S&F extruded aluminium alloy butt hinges 100mm size type B-21 all as specified & directed.

S&F 150 mm long aluminum anodized barrel tower bolt extruded section.

S&F aluminum handles cast type anodize 150 mm long.

S&F 300 mm long of bolt Mild steel sliding door bolts,plate type,stove enamelled black,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolt plate and two on staple plate complete all as specified and directed.

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate of Brass complete all as specified and direcetd.

S&F mild steel works as in small articles like hold fasts, conforming to Fe-290 or Fe E-165 all as specified & directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making dismantaled portion in CM (1:3) or cement concrete 1:2:4 Type B-1,Depth of embedded portion of Holdfasts not exc.half brick Complete all as specified and directed.

Taking up or down steel tubing and connection of 15 mm bore complete all as specified directed at site.

Description all as per ser item No 33 above but for 20 mm dia bore pipe.

Supplying and laying 20mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying 25mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

20mm CPVC Brass Elbow for 'hot or cold' water supply connection and similar works etc,.

20mm CPVC Brass Tee for 'hot or cold' water supply connection and similar works etc,.

Dismantling of boarding any description, fixed in any position with screws all as specified.

S&F prelaminated particle board 18-19 mm thick interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination to timber frame work in Cupboard all as specified and directed.

S&F 30mm width of flaps continues piano hinges mild steel bright finish or elec-trogalvanised complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittins,heads,shoes,bends,swan-necks,etc including removing from site.

M&L for 110mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

M&L for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

S&F PVC (SWR) bends 110 mm bore of any radius all as specified & directed.

S&F PVC (SWR) bends 75 mm bore of any radius all as specified & directed.

S&F PVC (SWR) junction single (singleT) equal or unequal 110mm bore provided with access door all as specified & directed.

S&F 110 mm bore PVC (SWR) vent cowl.

S&F 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement.

S&F 110mm dia PVC (SWR)WC connector with lip ring.

Demolition and breaking up drain pipe 150 mm internal dia of pipe (salt glazed ware, AC or reinforced concrete) sat in cement mortor.

M&L for 150 mm dia of reinforced concrete pipe, class NP2, laid and jointed complete with collars as specified and directed.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone agg for concrete bed to drain pipes including , packing under and haunding against the sides of pipe, after they tested for 150 mm dia pipe.

Demolition of brick ston masonry built in cement mortar.

M&L for brick work using sub class B bricks straight of curved on plan exc 6m mean radius built in CM (1:4) Complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick wall built in CM (1:4) Complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping, bed plate etc complete all as specified and directed.

M&L precast cement concrete type B-1 (1:2:4) using 20mm graded aggregate as in cover slab, shelves, and similar work set in CM (1:4).complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in lean concrete for foundation in drain,manholes etc all as specified and directed.

M&L for mild steel TMT bars 8 to 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L rendering 10mm thick on fair faces of brick or concrete surfaces and finishing the surfaces fair and even without using extra cement in CM (1:4) with W.P.C (W.P.C will be measured and paid separately) complete all as directed at site.

Supply only integral water proofing compound. (Make - ACCO PROOF/WATER SEAL/ IMPERMO)

S&F in repair for 10ltrs capacity flushing cistern PVC low level valve less, symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and 32 mm flush pipe of polyethylene complete all as specified and directed.

S&F in repairs stop valve/angle cock fancy type of 15 mm dia cast copper alloy chromium plated screwed down, high pressure, with crutch or butter fly handle long shank and cup (concealed type) screwed both ends for iron pipes or for unions.

S&F in repair 20mm bore stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair, 15mm bore bib taps cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F for 15mm bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down,high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair brass chromium plated wall mixer with hot and cold arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC.(make- Essco)

S&F in repair brass chromium plated Basin mixer with hot and cold arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC..(make- Essco)

S&F in repairs for shower rose chromium plated with or without swivel joints 75 mm dia complete all as specified and directed.

S&F in repair vitreous china pedastal type watre closet, white (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete and making good to floor.

S&F in EWC sheet cover to match EWC complete.

S&F in repairs Health fauset (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook incl making connections and fixed in position complete in all respect as specified.

S&F for vitrious china wash basin, white flat back size 550 x 400 mm including waste, chain & plug and poreclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for WHB etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waiste pipe fitted complete all as specified and directed.

S&F for pillar tap of 15mm dia bore pipe, fancy type cast copper alloy with capstain head chromium plated with or without lettered “hot or cold” with long screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified and directed.

S&F PVC connection pipe of 15 mm dia and 45 cm long to WHB and flushing cistern complete all as specified and directed.

S&F in repair stainless steel kitchen sink with drainage board 1 mm thick including bedding in cement mortor on to dwarf wall or including fixing centilever brackets over all size 915 mm x 460mm bowl size 410 mm x 330 mm x 160 mm and including 38/40mm dia waiste pipe complete all as specified and directed.

Disconnecting existing tank of capacity exc.500 & n.exc 1000 ltrs, setting aside lowering if required for repairs cleaning etc and hoisting if required reconnecting and refixing in position

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tank three layered (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod &highdensity plastic ball screwed for iron pipe and fixed.

M & L 20 mm thick granite tiles machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen slab.complete all as specified and directed by Engineer-In- Charge.

M&L for applying three coats of white wash on newly plastered surfaces on wall after necessary preparation of the surface, complete all as specified and directed.

M&L for preparation of old decorated surface of walls by brooming down and wire brushing etc and applying two coats of white wash on wall complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall / ceiling and applying distemper oil emulsion two coats on 3mm thick wall care putty (in two layers) including priming coats complete .

Complete removal of existing treatment of walls/ ceiling and applying two coats of distemper oil emulsion over 3mm wall care putty (in two layers) including priming coats complete .

M&L for Preparation of old plastered or unplastered surfaces of ceiling and applying two coats of white wash to ceiling complete all as specified and directed.

M&L for preparing the newly surface of any description not otherwise described over 10 cm width or girth on steel surface and applying two coats of synthetic enamel paint over one coat of zinc chromate primer all as specified and directed.

M&L for preparing the new plastered surfaces of wall and applying two coats of cement base paint of any colour over one coat primer complete

M&L for applying Two more coats of 100% Premium acrylic amulsion paint having VOC less than 50gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of exterrior primer applied @ 0.90 litre/ 10 Sqm over new surfaces.

Dismantaling floor, hearth or wall tiling, including cement mortar bedding (but not backing ) removing serviciable tile to store & rubbish off the permisses.

M&L for 10 mm thick cement plaster in CM (1:4) for backing of tiles complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 300x450x7to8mm thick set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18sqm infloor etc;set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L vetrified ceramic tile 10mm thick (square/rectangular) light shed area of each tiles n.exc 0.36 sqm in floor etc;set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete .

M&L for machine cut Kota stone slab flooring 18-20 mm thick (square or rectangular size.) over cement screed bed laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Description all as per ser item No 95 above but on vertical surface as dado/ skirting.

S&F brass CP tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and as directed by Engr-in-charge.

Removing/taking down of old water proofing treatment from roof/concrete surface removal to distance exc 250mtr and not exxc 500mtr from the site & cleaning of the roof surface with wire brush to make it free from dust, dirt etc complete.

M&L for roof treatment in repair by complete removel of existing old treatment and treated with following specifications :- (a) Brushing neat cement slurry @ 3Kg per Sqm on roof slab. (b) 15 mm thick cement plaster fair finished using cement mortar (1:4) with WPC on roof slab. (c) Applying oil based bitumen primer @ 0.30 ltr/Sqm on plastered surface. (d) Applying a tack coat of hot air blown bitumen of grade 85/25 in two coats each coat @ 1.2 Kg/Sqm, 1st on bitumen primer and 2nd on polymeric water proofing membrane complete. (e) Applying water proofing membrane not less than 4 kg/sqm in weight, sealing as directed at site with 100 mm over laps as per manufacture's instruction. (f) Applying one coat of aluminium paint @100 gm/Sqm over bituminous surface of membrane. Note : Supply only WPC shall be measured and paid separately under relevant item.

Dismantling of wall and ceiling boards any thickness including corner fillets.

M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre incl 2mm dia G.I. ( upto 1200 mm length ) adjusting level to Purlins/ Rafter. .

M&L 4mm thick non asbestos fibre cement designer building board of size 600X600 fixed or laid/inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping.

Dismantling timber scantling 40 sqcm and over in section in any position in unframed work.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work.

S & F roof trusses (framed ) trussed, purline , crane gantries , rafter, rails and fastening and heavy brackets framing fast and similar small (beam, Tee, angle , channel plates or flat sections) including distance pieces cleats etc and necessary nuts bolts , rivets, welding, plates etc complete all as specified and directed by Engr-in-Charge Quality confirming to Fe-410-W ( Gde E-250) quality B.

Dismantling AC corrugated /semi corrugated sheets in roof covering complete all as specified and directed.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated/ Semi Corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M & L PCC 1:3:6 type C2 , using 20mm graded aggregates as in 75mm thick plinth protection including bitumen joints in 1.0 Mtr centre to centre as required.

M & L for preparation of old painted steel & iron surface of any description over 10 cm width or girth when connected with other painting or when painted in different tint applying two coats of synthetic enamel paint over on steel surface

M/L Complete removal of existing treatment on wall and applying two coats of cement base paint of any colour over one coat primer complete

M & L applying two coats of synthetic enamel paint over a coat of pink primer incl cleaning for new wooden surface.

S&F aluminum handles, cast type ,anodised 150 mm

Taking down carefully copper/aluminium point wiring (light, fan socket or power) complete including fittings & fixtures such as switches, ceiling roses, pendents, regulators etc and making good disturbed surface of walls, floors etc complete all as specified & directed by Engineer-in-charge. Note :- Light fittings shall be measured & paid separately.

M&L for point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including medium grade, PVC consealed conduit of 20mm bore with accessories in wall/roof/floor etc, ISI marked with mild steel/prestressed steel modular sunken/concealed box (with earth dolly) duly painted two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, covered with white modular cover base plate for mounting switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth duly completed all as specified and directed by Engr-in-charge for the following .

One light or fan point, controlled by one, one way switch 5 Amps.

One socket out let 3 pin 5 Amps on the same board.

One socket outlet of 3 pin 5 Amp on independent board.

One bell point controlled by one 5 amp bell push

Material and labour for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including medium grade, PVC consealed conduit of 20mm bore with accessories in wall/roof/floor etc, and sunken galvanized pressed steel terminal boxes of thickness not less than 1.12 mm covered with covered with white modular cover base plate for one 15 amp socket outlet controlled by one switch on independent board incl 1.5 Sq mm copper conductor earth wire and connected to common earth dolly on independent board.

S&F in repair ceiling rose, PVC of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

S & F in repair bell push 5 amp flush type

S & F in repair modular switch 1 way 6A, 1 module.

S & F in repair modular switch 1 way 16A, 1 module

S & F in repair modular socket, 6A - 3 pin combined 2 module

S & F in repair modular modular Socket 6A/16A - 3 pin combined 2 module.

S & F in repair modular fan regulator step type, 120W - 2 module

M&L in repair modular white cover plate with frame ( both inner plate & outer plate cover), 1 module.

M&L in repair modular white cover plate with frame ( both inner plate & outer plate cover), 2 module.

M&L in repair modular white cover plate with frame ( both inner plate & outer plate cover), 3 module.

M&L in repair modular white cover plate with frame ( both inner plate & outer plate cover), 4 module.

M&L in repair modular white cover plate with frame ( both inner plate & outer plate cover), 6 module.

M&L in repair modular Modular metal flush box 1 & 2 module

M&L in repauir modular metal flush box 3 module

M&L in repair modular metal flush box 4 module

M&L in repair modular metal flush box 6 module

S&F in repair MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge.

S&F in repair MCB single pole & neutral 40 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge.

S&F in repair sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 8 way with 200 Amps rated copper bus bar double door type complete all as directed by Engineer-in-charge.

S&F in repair sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 4 way with 200 Amps rated copper bus bar double door type complete all as directed by Engineer-in-charge.

S & F in repair bell ding dong type 230 v, 50 Hz

S&F in repair, lamp holder, PVC/ polycarbonate type with back plate suitable for batten fittings and including LED lamp 12 watt complete all as specified and directed by Engineer-in-charge.Make : Crompton Greaves/Havells/Philips/Bajaj

S & F in repair LED building Security light fitting 1x20watt with polycarbonate housing, Aluminum gear tray duly prewired inbuilt LED module IP 65 Protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS,FI clamp including plinth with nut bolts etc complete all as specified and directed Make: Crompton Greaves/Havells/Philips.

Taking down existing earthing and M&L for new Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 5 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. Note:- (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 5 of MES SSR Part-I. ( ii) Item includes the cost of 7.5M GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth lead wire. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall

S&F in repair service connection of 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathed of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core multistandard cable flat or circular of 6 Sqmm 2 core including taking down old service cable complete all as specified & directed by Engineer-in-charge.

M & L in repair for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 Sq mm (FRLS) in PVC casing & capping non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6 Sq mm (FRLS) of continuous earth wire green in colour complete all as specified and directed by Engineer-in-charge. (NOTE: Two runs of 6.0 sqmm cable & One run of 6 sqmm cable and One run of PVC casing & capping shall be paid as one unit length.)

Taking down old unserviceable LT cable, supply and Laying in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer In charge of cross sectional area of 10 Sqmm 2 core

Excavation in trenches not exceeding 1.5mtr wide & not exceeding 1.5 mtr in depth for laying LT cable, hard/loose soil complete all as directed.

Returning, filling in trenches with soil, including spreding, leveling, watering & well ramming, in layers not exceeding 25 cm each complete

Removing surplus excavated material (soil) to distance not exceeding 50 Mtr & depositing where directed at level not exceeding 1.5 mtr above the starting point.

Sand filling in cable trenches for cable protection with clean dry sand unwashed including gently put in trench

S&F for old size brick well burnt, laid flat, for cable protection complete all as specified and directed.

S & F in repair box type fitting 1x 16w, blue coloured end caps, prewired for LED tube including LED tube 16 watts, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”. Make: Cromton Greaves Cat part no for Fitting DMLN1LT8-16 and for LED tube LTT8-16 or Equivalent make of Havells/Philips.

Supply and fix exhaust fan steel boday Ac singal Phase . 230V OF size 300m sweep with ,blades, and frame and louvers.

Supply and Fix electric water heater storage type steel body with copper inner tank and heating element upto2 KW capacity 25 Litre BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, as ,connection piece etc. . Make : Bajaj/C&G/ Havell's (Monza EC). Note : Old uns geyser will be deposited to store yard SDO Jamshedpur and Engr-in-Charge shall taken on charge and shall be mentioned in demolition statement.

Supply and fixing in repair ceiling fans complete with blades down rods ,electronic regulator and accessories, 230V, 1200MM sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five ster rated with brushess direct current motor (BLDC) Note: Old uns Fan shall be deposited to store yard SDO Jamshedpur and Engr-in-Charge shall taken on charge and shall be mentioned in demolition statement.

UPENDRA KUMAR SINGH (BID ID -3475610)

M/S VIKAS CONSTRUCTION CO. (BID ID -3483460)

M/s ASEDHA ENTERPRISES (BID ID -3478965)

M/S ANUJ KUMAR (BID ID -3478829)