Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹31.2 LAccepted-AOC ASHOKA PARK PALLAVA PARK BVT INS VISHWAKARMA INDIAN NAVY OF GE ND VISAKHAPATNAM | L1 | Accepted-AOC BEING L1 BIDDER | |
| 2 | L2₹33.2 L+₹2.0 L (6.43%)Rejected-Finance | L2 | Rejected-Finance BEING NOT L1 BIDDER | |
| 3 | L3₹33.8 L+₹2.6 L (8.24%)Rejected-Finance CHENNAI | L3 | Rejected-Finance BEING NOT L1 BIDDER | |
| 4 | L4₹34.4 L+₹3.2 L (10.2%)Rejected-Finance C 234 ADG P CHENNAI | L4 | Rejected-Finance BEING NOT L1 BIDDER |
Tender Value
₹29 L
EMD Value
₹58,000
Closing Date
4 Nov 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Shri Ashwani Mittal EE GE DSSC
GE DSSC WELLINGTON BARRACKS-POST, WELLINGTON, THE NILGIRIS, TAMIL NADU,PIN-643231
IMPROVEMENT TO OVER HEAD RERVOIR AND UG SUMPS AT DSSC WELLINGTON
2023_MES_622282_1
8377/E8
Open Tender
Civil Works
Item Rate
120 days
WELLINGTON
PLEASE REFER TENDER DOCUMENTS AND NIT
8 documents required · 8 mandatory
₹500
GE DSSC WELLINGTON
₹58,000
Yes
23 Nov 2023
9 Oct 2023
6 Nov 2023
9 Oct 2023
4 Nov 2023
23 Oct 2023
Amount
Demolition of cement concrete (unreinforced ) Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris off outside MD land complete all as spcified and as directed.
Demolition of concrete of any description and in any position complete as in drain etc all as specified and as directed
Dismantling MS steel work of any descrption as in fencing post,MS line wire ,Gate etc complete all as specified and as directed
Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.
M&L for V groove of 10mm wide and 30mm deep or up to the extend of joint/crack present at site over joint /crack line using electrically operated angle grinder with diamond concrete saw blade and cleaning it by air blower as directed by the Engr In Charge.The groove shall be cut on the concrete surface along the joint /crack over RCC structure to be executed by the authorised applicator of the manufacture height up to 15 Mtr complete all as specified and directed.
Description all as item No 5 above, but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L for examining the weak concrete portion of RCC member of any description by tapping with light hammer and marking of the loose concrete area of structural element in straight line geometrical forms ,grooving the edges same with grinder up to 5-10mm depth and drilling holes in honey comb portions for installing PVC nozzles of 12mm dia complete height up to 15M all as specifed as per manufactur instruction.
Description all as item No 7 above, but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L for sealing of exposed ' V' groove of 10mm wide and 30mm deep with sikaguard 694 F(I) or quick fix or equiavalent solvent -free ,moisture tolerant ,thixotropic ,two part structural adhesive including level the surface with cement mortar(1:4) height up to 15M complete
Description all as item No 9 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L for drilling holes of 12mm dia up to 100mm deep holes in structural members at the interval of 300 mm in staggered manner or along the joints & crack line in reinforced concrete (RCC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and machined external end to receive the out let of grouting gun including fix inside the hole by applying thixotrpic epoxy adhesive Sikadur 31 IN Re arm Instaplug /quick fix to ensure complete sealing and allow curing system for minimum 8 Hrs before grouting including nozzle projections including making necessary levelling/making good the epoxy surface through necessary grinding,levelling etc all as directed height up to 15M.
Description all as item No 11 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L for injection grouting of conctruction joints with non shrink cement slurry admixed with epoxy grouting Cebex 100 of M/S Fosroc Chemical/Sika Grout -214 IN @300 mm C/C including opening of cracks to a groove of size 12mm x12mm ,nozzle at 300mm C/C including of opening of cracks to be grooved of size 10mm x10mm and fixing of nozless with fast setting plugging compound Renderoc plug,cutting out extra lenth of nozzle after grouting all in complete as per manufactires instructions including the necessary scafolding as required height up to 15M and as directed by the Engr In Charge.
Description all as item No 13 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M & L for two coats of Sika Topseal 107 or Aqua Arm top Guard inside of the wall & floor of the tank.(two componenets shall be ready to use polymer modified cementatious coating).First coat shall be applied horizondally and second coat shall be applied vertically(Thickeness of the coating shall be not less than 1.5mm) complete all as specified and directed. Not: Water ponding test shall be carried out after the stage of aplication of two coats)
Description all as item No 15 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
Material and labour for applying two coats of Aqua Arm Tank Coat ,a water based epoxy coating for portable water on all over the concrete surface from inside and leave the treated surface for 6-8 hrs for dry and apply 2nd coat and and allow the surface to cure for 24 hrs.The thickness of the two coat(After application) shall be not less than 400 microns complete all as specified as manufacture instruction .(The applcator shalll be from authorised Manufacture only)
Description all as item No 17 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L for Precast cement concrete block Type C1(1:3:6)(using 20 mm graded aggregate) masonry with solid solid blocks exc 10cm width and setting in mortar(1:6) complete.
Material and labour for Rendering in Cement Mortar 1:4, 10mm thick on brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed..
M & L for PCC 1:3:6 type C-2 using 40mm graded stone aggragate steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as directed
M&L for MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as directed by the Engr In Charge.
M&L for complete removal of external finish on old plasterd surface of RCC members like dome/Columns etc of OH or semi UG water storage tank surafce including necessary scafolding and apply ,two coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint APEX ULTIMA of Asian Paint or WEATHER COAT SMOOTH of Berger complete all as per manufacturer instruction as directed height up to 15 M .
Description all as item No 23 above but height exceeding 15 Mtr but not exceeding 30Mtr complete.
M&L Preparing newly plastered surfaces of external walls and applying exterior wall putty of 3mm thick for smoothness, one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger complete all as per manufacturer instruction as directed.
Material and labour charges for chipping the spalled and old concrete removing loosely adhering particles using wire brushes and make the structure for the application of micro concrete complete complying with standard specification including lead and lift for an average thickness of 50 mm including disposal of debris to within site low lying area as directed by Engineer-in-charge. (Note : 1. The cleaning of the bar shall be done such that no rust shall be present after removal of rust from the bar. 2. Removal of concrete which is defective shall be right round the bar, which is going behind the thickness shall be included)
Supplying and fabricating and placing in position of new TMT bars of any dia by welding or inserting by drilling holes and embeded in epoxy grout bonding agent of hilti or equivalent for all existing reinforcement repair works in any position wherever necessary complete all as specified and as directed by Engineer-in-charge. Note: The lap provided shall be 15 cm on either side of bar which has lost its sectional area.
M&L for exposing the existing reinforcement bars fully in the repair area and remove all loose scales and corrosion deposits using Dr. Fixit Rust Remover or equivqlent and applying protective zinc primer using Fosroc Nitoprime Zincrich or Dr. Fixit Zinc primer or equivalent on bars of dry thickness 40 micron (wet thickness 130 micron) with approx coverage of 7.40 Sqm/litre before concreting.
Supply & Fixing of slurry tight formwork which shall not deform or leak due to pressure of micro concrete shall be fabricated and erected in position. Provision shall be made for a suitable feed hopper for pouring in the micro concrete in the formwork. The form work shall be coated with Nafuplan UST liquid for steel surfaces, Nafuplan-K for wooden surfaces or Fosroc Reebol mould releasing agent or equivalent releasing agent prior to final fixing in position as per manufacturers instruction. Proper supporting arrangements to be made for keeping the shutter in correct line and length complete all as specified and as directed by Engineer-in Charge.
M&L for stocking sufficient quantity of micro concrete material comprising 10 mm down graded aggregate chips, pouring in a continuous operation with a grout/ concrete mixer of low speed heavy duty dram fitted with suitable paddle shall be kept ready and chips slowly mixed in the dram throughly in a forced action. The mixed materials shall be placed immediately in to the position formwork continuously without any time gap complete for an average thickness of 40 - 50 mm including finishing the exposed surface to an even and smooth surface completely all as specified and as directed by Engineer-in charge. The micro concrete shall be Shikacrete-114 AE or Dr. Fixit Micro Concrete or equivalent of Manufactured by Fosroc or Bouchemie.Note for item No 26 to30: Quoted rates includes cost for necessary formwork/steel scofloding upto a height of 30Mtr.
Surface Excavation n. exc. 30cm deep & avg 15 cm deep & getting out in hard dense soil complete all as specified and directed.
Excavating in trenches, n.exc 1.5m wide and n exc 1.5 in depth; for foundation getting out hard/dense soil complete all as specified and directed.
Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in foundation filling and mass concrete for manhole&Septic tank all as specified and as directed.
M&L for 15 mm thick rendering in cement mortar 1:4 on brick work or block masonry surfaces of wall(for manholes), finished even and smooth with using extra cement complete all as specified and as directed.
Precast RCC 1:2:4 type B1 using 20mm graded stone aggregate for cover slab of set in CM 1:4) including form work as necessary. Note:Reinforcement will be measured and paid separately) i
Supply and fix TMT 10 mm dia and over cut to length bent to shape required and cranking, hooking ends and binding with MS wire annealed not less than 0.9mm dia
M&L 75mm thick PCC 1:4:8 type D2 (40 mm graded aggregate) as in Sub base floor finished even and fair as in sub base of floor etc all as directed by the Engineer In Charge.
M&L for chequered cement concrete tiles of size 30cmx30cmx 25mm thick ,set ,jointed and pointed in neat cement slurry in floors with grey cement and pigments of required colour over 20mm thick thick screed bed in CM (1:6) complete as specified and as directed.
M &L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in Walls, retaining walls, basement walls, ballast walls and the like;any thickness; above top of footings; including attached pilaster and buttresses complete all as directed by the Engr In charge.
M&L use and waste of timber as in formwork to faces of walls, retaining walls, abutments, parapets and beams,columns and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for fair finished surfaces of concrete flat.
S&F in repair Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia weight exc 4Kg fixed in reinforcemnt or MS frame work complete as specified and as directed.
Returning filling including spreading leveling watering and well ramming in layers not exc 25 cm hard and dense soil complete all as specified and directed.
Removing excavated materialnot exc 1.50kmm but n exc 5.0km and depositing where directed (Soils) at a level not exc.1.5mts above the starting point complete all as specified and directed.
M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade jointed with grey cement without pigment over 40mm thick sand cusioning complete
M & L for plain cement concrete type-C2, 1:3:6 (40mm garaded agg.) in surface channel and drains including necessary form work and forming fair finish the surface complete all as specified and directed
M/L preparing new surface of steel and appling two coats of synthetic enamel paint over a coat of primer red oxide complete all as specified and directed
M/L Preparing old steel surfaces girth exc. 10 cm girth and applying one coat of synthetic enamel paint complete all as specified and directed
M/L Preparing old steel surfaces girth n,exc. 10 cm girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M/L Preparing old plstered /concrete surfaces girth exc. 10 cm girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M& L for Painting lines, dashes, arrows, letters, etc on concrete/plastered , pavements and the like exc 10cm wide with road marking paint, white or golden yellow including preperation of the old/new surface complete all as specified and directed
C A RAJENDRAN CONSTRUCTIONS
VVM CONSTRUCTIONS
GMS Builders
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .