REPAIR AND MAINT OF E/M WATER SUPPLY INSTALLATION, CLEANING OF OH AND UG TANKS AND EXTERNAL WATER SUPPLY PIPE LINES AND COMPREHENSIVE REPAIR/MAINT OF LT PANEL, LT UG CABLE, APFC PANEL AND ALLIED WORKS AT NRS AT 31 WEU THANE UNDER GE (NW) M

Amount

Notes : (i)The contractor should be in possession of valid electrical license to execute electrical works. (ii) Supervisor for execution of electrical works/ electrical component of works employed by the contractor shall possesses supervisor certificate of competency issued by concerned State Government/ Union Territory and the worker/ tradesmen for execution of electrical works/ electrical component of works shall hold necessary permit issued by concerned State Government/ Union Territory. M&L for cleaning underground / semi-underground sumps of 10,000 gallons capacity by draining out sludge from bottom, by blocking all inlet/outlet, removing alge-fungi growth from wall, floor, ceiling by wire brush/ water jet pressure machine, cleaning complete surface and dis-infecting with bleaching powder and writing in paint approved font of size "Date of Cleaning" and "Capacity" of tank all as specified and directed.

-Ditto- all as per item No 1.00 above but 20,000 gallons capacity.

M & L for cleaning of over head reservoir 20,000 gallons by draining out water,removing sludge, alge-fungi growth from walls/floor, roof by rubbing with wire brush and disinfecting the reservoir with bleaching powder, draining out and making reservoir totally clean and writing in paint approved font of size "Date of Cleaning" and "Capacity" of tank all as specified and directed.

M & L for cleaning RCC / PVC Service Tanks upto 500 Ltrs capacity by draining out entire water, removing sludge, mud etc, cleaning the ceilings from spider webs, mud accumulations etc., with water jets etc., brushing / rubbing with wire / nylon brush / mop to remove all algae / fungal growth and moss etc. entirely from walls, floors, etc. washing clean with fresh water by using water jets and then again washing and treating with anti - bacterial agents, disinfectants and bleaching powder, as required at site and writing in paint approved font of size "Date of Cleaning" and "Capacity" of tank in cleaning off the premises complete all as specified and directed by the Engineer-in-charge.

-Ditto- all as per item No 4.00 above but 1,000 Ltrs capacity.

-Ditto- all as per item No 4.00 above but 1001 Ltrs to 2,000 Ltrs capacity.

-Ditto- all as per item No 4.00 above but 2001 Ltrs to 5,000 Ltrs capacity.

M & L for servicing of Centrifugal pump set upto 20 HP by taking to workshop and opening end covers, greasing the bearings, replacing worn out nut, bolts, gasket, air release valve key, gland stuffing box male/ female set, Rubber bush and painting one coat of synthetic enamel paint, including writing/marking in 1" size letters SM & MES No and reinstalling in existing foundation complete with testing all as specified and directed by Engr-in-Charge. Note :- (i) Parts if required for pump shall be measured and paid separately here-in-after under another item as 'supply only.

-Ditto- all as per item No 8.00 above but Pump set 5 HP

Supply only Ball bearing 6207 all as specified and directed.

Supply only Ball bearing 6208 all as specified and directed.

M&L for rewinding of electric motor 3 phase 50 Hz 415 volt for 15 HP capacity complete all as directed and specified. (a) Disconnecitng, dismantling existing burnt winding from motor and rewinding complete with super enamled copper winding wire of matching gauge including all insulation material such as PVC insulated sheet, cotton tape sleeves varnish etc., (b) Transporting electric motor including loading/ unloading upto wksp and back to site. (c) Re-installing the same at the orignal locaition with proper alignmenent connecting and testing on load. (d) Replacement 2 Nos ball bearing for each motor of existing size/model. (e) Replacement of winding terminal plate with brass stus,/nut, bolt washer. NOTE: Quoted rates shall be deemed to include one year warranty for motors after rewinding and commissioning.

-Ditto- all as per item No 12.00 above but Motor 5 HP Cap

S&F cast iron covers, circular, for overhead PVC / RCC water storage tanks of any size, with MS strip / flat iron framework, with all necessary fixing and locking arrangements, nuts, bolts, washers, all as per BMC standards, with a shop coat of primer, including all necessary scaffolding / staging as required to cater at heights, taking out and disposing off old PVC covers, making any required addition / alteration to the tank for fixing of new CI covers, etc. complete all as specified, as directed by the Engineer-in-charge. (weight of tank cover not less than 10 KG).

M & L for preparation of old painted / unpainted surfaces of any description, including taking out of parts / components under painting (if required) from any position / location as listed hereinunder and applying one coat of epoxy paint (with colour code maintained as per relevant IS) including marking with flow directions (of approved colour) complete al as specified and as directed by the Engineer-In-Charge. (a) Induction motors 15 HP/20 HP - 03 Nos. (b) Filteration plant 10,000 GLNs/Sec - 01 No. (c) Electric motor 5 HP - 01 No. (d) Sluice valve 100 mm dia. - 03 Nos. (e) Sluice valve 80 mm dia. - 03 Nos. (f) Electric Panel Board - 02 Nos

Supply only Calcium based granular disinfectant for drinking water treatment having 60% to 70% chlorine content in granular, sealed/ packed in 45 Kg drum.(Free from toxic constituent) all as required and directed by Engr-in-charge. Make- Purichlor/Declibac/potter & watts or other equivalent make.

Supply, fixing, jointing and testing of 80 mm, CI Sluice Valve heavy duty PN 1.6, IS-14846 with iron wheel head jointing, coupling both ends for cast iron pipes including nuts, bolts, rubber gaskets etc including taking down old unserviceable sluice valves complete all as specified and directed .

-Ditto- all as per item No 17.00 above but 100 mm bore

S& F in repairs PVC Service Water Tank of 500 Ltrs capacity including tank nipple, bends, sockets complete all fitting required at site all as specified and directed.

-Ditto- all as per item No 19.00 above but 1000 Ltrs capacity.

-Ditto- all as per item No 19.00 above but 2000 Ltrs capacity.

Taking up or down steel water tubing of size 15mm to 80mm bore and connections including cleaning and setting a side for refixing, etc complete all as specified and directed

Supplying, laying, connecting and testing of GI tubing medium grade of 25 mm dia with and including all fittings such as bends elbows, tees, short pieces, connectors, check nuts, diminishing pieces, caps and plugs, unions,etc fixed complete laid in trenches / along the walls / poles / ceilings / floors / ducts / on pillar post / road crossing all as specified and directed.

-Ditto- all as per item No 23.00 above but 40 mm dia.

-Ditto- all as per item No 23.00 above but 65 mm dia.

-Ditto- all as per item No 23.00 above but 80 mm dia.

Taking up old CI/DI pipe of upto 100 mm bore and connections including cleaning and setting a side for refixing, etc complete all as specified and directed

M&L DI pipe 80 mm bore with spigot & socket ends centrifugally cast class K-7 in any length laid in trench including rubber joint (tyton joint) as required etc complete all as specified and directed

-Ditto- all as per item No 28.00.00 above but 100 mm dia. Note for Item Ser No 23 to 29 : Excavation, returning filling and shall be measured and paid separately under respective item of schedule "A".

M&L for DI fittings of class K-12 such as bends , collars, caps, plugs, connecting pieces any type upto 150 mm dia complete all as specified and directed.

M & L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying cable/ CI/GI tube, returning filling & well rammaing watering finish surface 10 cm from top using PCC 1:3:6 including removal of surplus soil etc complete all as specified and directed

M & L for dismantiling the existing valve chamber of size 900 X 900 X 900 mm including necessary earth work in any type of soil, PCC foundation D-2 1:4:8 in base concrete, brick work in CM 1:6 with 10 mm thick in CM (1:6) plaster internally and 15 mm thick externally in CM 1:4, 3.15 mm thick MS cover with hinges and locking arrangement fixed to angle iron frame made-out of 40 X 40 X 6 mm MS angles complete with 2 coats of synthetic enamel paint over one coat of red oxide zinc chrome primer on all metal works including necessary excavation earth work all plastered surfaces of valve chambers complete all as specified and directed

M & L in replacement of run lead joint for CI Spigot and socket 80 mm bore pipes and fittings etc complete all as specified and directed

-Ditto- all as per item No 33.00 above but 100 mm dia.

M & L in replacement of rubber gasket joint of the size 80 mm size for CI flanged type pipe including nut, bolt, washer complete all as specified and directed .

-Ditto- all as per item No 35.00 above but 100 mm dia.

S & F in repairs Gun metal gate or globe valve 40 mm dia, confirming to IS-778, ISI marked, with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc. and any addition / alteration required for threading and fixing complete all as specified and as directed

-Ditto- all as per item No 37.00 above but 25 mm dia.

Supply and fixing of cast iron flanged ends sluice valve suitable for 100 mm dia pipes conforming to IS - Class PN - 1.0 with MS nuts, bolts, washers etc, as approved including taking out/ dismantling old unserviceable one and testing complete all as specified and as directed.

S & F in repairs float ball valve assembly 20 mm bore , high pressure grade, with polythene float, fly nuts, screwed to GI pipe or brass ferrule, CI fittings viz. nipples, check nuts, reducers, elbow, sockets, etc. fixed etc complete all as specified and directed

-Ditto- all as per item No 40.00 above but 25 mm bore

-Ditto- all as per item No 40.00 above but 40 mm bore

Drilling and taping cast iron water mains (in position) for branch connections 15 mm bore of the internal dia including ferrule and required fittings all as specified and directed.

-Ditto- all as per item No 43.00 above but 20mm bore

S & F fully automatic star delta starter suitable for 15 HP motor conforming to IS -13947-4 after taking down old unserviceable one etc complete all as specified and directed. Make- Havells

M & L for PCC 1:2:4, type B-1, (using 20mm graded stone aggregate) as in foundation for pump sets and blocks including necessary form work complete all as specified and directed.

Supply and fix in repair Mild steel type 'C' Channel made of any angle iron of suitable size for pump foundation frame of any size suitable for site by welding including all necessary nuts, bolts, washer complete all as specified and as directed.

Supply and fix in replacement ladder height 10 feet max, steps on every 01 feet made of angle iron of size 50x50x5 mm thick for sump complete all as specified and directed.

M& L for attending day to day complaint of minor nature including replacement of fittings such as elbow,socket,tee etc and deposting the complaint slip in complaint cell after user signature etc complete all as specified and directed Note :- (i) The representative of the contrcator (Supervisor - 1 No, Plumbar Skilled - 1 No, Helper - 1 No shall report to Engineer-in-charge/JE and carry out repairs on daily basis during the contract period (ii) The work shall be executed in buildings of NRS Thane, HQ 31 WEU Thane.

M&L for provn of Earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the plate not less than 1.5M below normal GL, connected to Galvanized earth strip 32x6mm upto 7.5 mtr with protection pipe by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I 2009 specification etc complete all as specified and directed.

S&F in repair GI strip size 32 x 6 mm including welding brazing etc complete all as specified and directed.

Supply and Fix in repairs Change Over TPN 400 Amps 415 Volt in open construction, panel mounted type with base plate for mounting in panel and reconnecting the cables with proper glands. Conforming to Cat No - CO44000 OOOO of L&T/Havells/Legrand/Standard

Supply & Fix in repair ACB 800 Amps, 4 Pole, 50 KA, Manual Draw out type, with Spring Charge Mechanism, over Load protection, Short Circuit Protection & earth Fault Protection, Metering Display including all necessary alteration required for fixing and testing complete all as specified and as directed.

S & F foot valve of size 80 mm dia cast iron body, ball type, with flanged and drilled ends and synthetic rubber coated MS ball, conformimg to relevant IS, ISI marked, including all joints, gaskets, bolts and nuts, washers, including taking up/down old unserviceable valves from any position and any addition/alteration for fixing required complete all as specified and directed. Make : Kirloskar or equivalant or as approved by GE.

Supply and Fixing in repair industrial type pressure gauge made out of SS 304 material, SS sipon shall be factory insulated with closed cell elastomeric insulation in tubing form, pressure gauges shall be factory fitted with a ball valve complete, all as specified and directed.

Supply and fixing in repair Gun Metal Air Release Valve of size 15mm bore, complete all as specified and directed.

S & F in repairs Perforated Brass Threaded End cap size 15 mm dia for over flow pipe of water tank as per BMC standard including all fittings like GI Nipple, Bend, Elbow, Tee, Socket etc complete all as specified and directed

Supply and fix in replacement of Rectangular LED Flood Light 350 Watt with innovative thermal management, multiple optics and equipped with IP66 protection flood light fittings including drivers, pressure die cast aluminium housing, prewired etc complete all as specified and directed. Make - Crompton Cat Part No -LSFO-350-CDL/60 / Havells/ Bajaj /Philips

Supply and fix in repair brass water meter of 100 mm class B flange type size all as specified and as directed. Make : Kranti/Capston/ Dashmesh

M & L MS cover in repair suitable for existing size with hinges and locking arrangement fixed to angle iron frame made-out of 40 X 40 X 6 mm MS angles with locking arrangement including necessary excavation earth work all plastered surfaces of chambers complete all as specified and directed

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in average soil including taking out cable protection cover etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

M & L for sand cushioning by spreading in trenches fine dry river sand by gently punning down manually as in cable protection all as specified and as directed

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches etc complete all as specified and directed

Laying only un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches etc complete all as specified and directed. Note :- Serviceable cable cover obtained from Ser Item No 61.00 shall be reused.

Dismentling of PCC foundation / pole coping from ground level all as per specified.

M & L for PCC 1:2:4, type B-1, (using 20mm graded stone aggregate) as in coping including necessary use & waste of form work complete all as specified and directed.

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 240 Sqmm 3.5 core including necessary connection and providing cable lugs as required including disconnection/taking down of existing cable all as specified.

-Ditto- all as per item No 69.00 above here-in-before but 150 Sqmm 3.5 Core -do-

-Ditto- all as per item No 69.00 above here-in-before but 95 Sqmm 3.5 Core -do-

-Ditto- all as per item No 69.00 above here-in-before but 16 Sqmm 4 Core -do-

-Ditto- all as per item No 69.00 above here-in-before but 10 Sqmm 4 Core -do-

M&L for preparing surfaces of steel tubular swaged pole LT with scraping out old paint by emmery paper, caustic soda complete and painting with two coats of aluminium paint and numbering of poles with white paint on black paint base and stripping with black paint (100 mm each stripe) 3 Nos at equal distance from bottom (above PCC coping) upto a height of 1200 mm complete.

M&L for preparation of old painted surfaces of pre-stressed concrete pole upto 11/9 mtr long by scarping old paint and applying two coats of cement base paint including numbering of pole with black oil paint painting the base of the pole in alternate black and yellow stripes each 30 Cm apart up to 1.5mtr height all as directed by Engineer in Charge.

Equipment and labour for servicing of ACB including drawing/taking out from LT Panel, cleaning the Contacts, checking the breaker accessories, replacing the burnt out control wiring, burnt fuse units, old unsversiable spring units for proper function and carrying out ratio test by applying primary injection all for LT ACB 630 Amps to 800 Amps and refixing the breaker in position and testing etc complete all as specified and directed. Note : The Contractor shall brought all T & P and testing equipments.

Supply and fix in repairs power factor controller relay 8 Stage RPM 8, 415 volts, 50 cycles suitable for manual / automatic operation with indication for each stage, power factor adjustment setting knob / screw, display.

M & L for testing of APFC panel for proper functioning in manual & auto mode, including re-wiring the burnt out wires, replacing the wiring ducts/casing Capping, fuse units and cleaning and testing complete all as specified and directed.

Supply and Fix in replacement of Contactor Three Pole 415 volts 25 Amps AC 3 Rating, Conforming to Type MNX 25 & Cat No - CS94110 of L & T or Equivalentt from Schnider Electric, ABB including add on Blocks suitable for driving POWER Capacitors, including making addition/Alternation to existing Wiring/circuit system

All as per item No 79.00 above but Contactor Three Pole 415 volts 32 Amps AC 3 Rating Conforming to Type - MNX 32 & Cat no - CS94111 of L & T or equivalent from Schnider Electric, ABB/ C&S

All as per item No 79.00 above but Contactor Three Pole 415 volts 40 Amps AC 3 RatingConforming to Type - MNX - 40 & Cat no - CS94190 of L & T or equivalent from Schnider Electric/ABB/ C&S

All as per item No 79.00 above but Contactor Three Pole 415 volts 50 Amps AC 3 Rating Conforming to Type -MNX - 50 & Cat no ST19001 of L & T or equivalent from Schnider Electric/ABB/ C&S

All as per item No 79 above but Contactor Three Pole 415 volts 70 Amps AC 3 Rating Conforming to Type - MNX - 70 & Cat no - ST19002 of L & T or equivalent from Schnider Electric/ABB/ C&S

Supply and fix in repair Power Capacitors of Rating 25 KVAR 415 Volt in repairs Naturally air cooled Double dielectric heavy duty, MPP type 440 Volt 50 HZ Watt Less Power Capacitors wattage not more than 0.5 Watt per KVAR conforming to IS 13340 and 13341 ISI Marked all as specified.

All as per item No 84.00 above but Power Capacitors of Rating 20 KVAR 415 Volt

All as per item No 84.00 above but Power Capacitors of Rating 15 KVAR 415 Volt

All as per item No 84.00 above but Power Capacitors of Rating 10 KVAR 415 Volt

All as per item No 84.00 above but Power Capacitors of Rating 7.5 KVAR 415 Volt

All as per item No 84.00 above but Power Capacitors of Rating 5 KVAR 415 Volt

Supply and fix in repair add on Blocks suitable for Power contactors of range 25 Amps to 140 amps (MNX 25 to MNX 140 including making addition/Alternation to existing Wiring/circuit system all of Make- L&Tor equivalent from Schnider Electric/ABB/ C&S

Maint/Cleaning of Sub stations inside and out side area and removing of creepers raised along with sub station including surface dressing around the sub station not less then 3 mtr from out side fencing and removing the all waste material from site and Chemical spray inside and out side area of Sub station. Note:- T & P will be arranged by contractor

Repair/Maintenance of LT Panel board by taking shut down, removing of carbon particles, rubbing of heated portion of bus bar and cleaning complete by means of CRC-226/Petrol, tightening of all joints in bus bar, checking of earth and neutral voltage and make a record, replacement of u/s nuts/bolts/washers including replacement of corroded glands, lugs/ thimbles and tightening them properly etc complete all as specified and directed.

Labour only for removing of creepers raised along with LT panels/feeder piller box etc surface dressing around the LT panels not less then 1.5 mtr in radius and removing the all waste material from site including suppling and spraying chemical for destruction of grass etc complete all as specified and directed.

Supply and fix in repair of Cable junction box IP 66/69 "weather proof" (with knockouts for cable entry) box of size 155 x 210 x 92 mm with connector/terminal, Din Rail, GI clamps made out of GI flat of size 25 mm X 3 mm channel including providing detachable GI 3 mm thick plate inside looping box as cable gland plate and including cable glands as required at size and making connections etc complete all as specified and directed. Make - Hensel cat part No KF1616B /National/Sintex or any enlisted make as specified in PS

Supply and fix in repair of Cable junction box IP 66/69 "weather proof" (with knockouts for cable entry) box of size 130 x 180 x 77 mm with connector/terminal, Din Rail, GI clamps made out of GI flat of size 25 mm X 3 mm channel including providing detachable GI 3 mm thick plate inside looping box as cable gland plate and including cable glands as required at size and making connections etc complete all as specified and directed. Make - Hensel cat part No KF1010B /National/Sintex or any enlisted make as specified in PS

S & F in replacement of Voltmeter Digital type ,0-500 Volts of size 96x96mm. Make : AE/L&T/Schenider

S & F in replacement of Ammeter Digital type of 0-400 amps capacity of size 96X96mm. Make : AE/L&T/Schenider

S & F in replacement of Phase indicating lamp neon type complete with holder assy RYB. Make : AE/L&T/Havells

S & F in replacement CT coils of ratio 400/5 Amps, 15 VA class -1 as per IS- 2705/92. Make : AE/L&T/Havells

M & L for taking down of 400 Amp ATS having two incoming and one outgoing, including opening the cable ends and disconnecting the incoming and outgoing cables and removing the ATS, cleaning and servicing and reinstalling the ATS after carry out necessary repairs to the ATS main controler, PCB Card, cleaning and earthing all parts and reconnecting the cables etc complete all as specified and directed.

M&L for taking down old unsv and supply & lay 3 Core 1.5 Sq mm size multistranded FRLS copper conductor PVC unsheathed 650 / 1100 Volt Grade As per IS 694 with and including 20 mm dia PVC conduit and passing through PVC conduit with necessary saddle, clamps, bolts & nuts, all for interconnection of cable looping box to Street Light Fitting, Post Top Lanternetc complete all as specified and directed.

Dismantling and taking down the existing defective street light fitting/Garden lights/Building security light of any type and any capacity from steel tubular pole, opening the street light fitting, checking the serviceability of spare parts including replacement of defective parts such as electric drivers and LED 36/70 watt after repairing including refixing on pole including connecting & testing etc complete all as specified and directed. Note:- Electronic drivers and LED will be measured and paid separately on respective item of Sch 'A' here-in-after.

Supply and fix in replacement flood light fittings in street light poles/Buildings the fitting shall be of LED type 150 Watts with and including drivers, pressure die cast aluminium housing, prewired etc complete all as specified and directed. The fitting shalll conform to cat No . ENDURAPULSENSL150WLED757PASYBOTG of Havells or Equivalent from Philips/Bajaj/Crompton

Supply and fix in replacement street light fittings in street light poles/Buildings the fitting shall be of LED type 60 Watts with and including drivers, pressure die cast aluminium housing, prewired etc complete all as specified and directed. The fitting shalll conform to cat No -ENDURAPEARLPLUSSL60WLED757SASYTOPC of Havells or Equivalent from Philips/Bajaj

S&F in replacement of building Security light fitting 30 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening seperate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings etc complete all as specified and directed. The fitting shall conform to Cat no ENDURAPEARLSL30WLED757SASYTOPCMP of Havells or Equivalent from Philips/Bajaj .

Supply & Fix in repairs 8 watts LED Bollard Garden light fittings with efficient high output LED, Pressure die cast powder coated housing with PC diffuser , driver nuts, bolt, washers, base plate, foundation 0.3 Meter x 0.3 Meter x 0.3Meter by PCC 1:2:4 type B-1 using 20 mm graded stone aggregates of size including excavation and earthwork, provision of GI bend of size 50 mm dia in the PCC for cable entry etc complete all as specified and directed. The Fitting Shall Conform to Cat No - CONEBL8WLED857SSYMTOPC of Havells or Equivalent from Bajaj/Crompton

S & F in repairs decorative 35 Watts LED Post Top Lantern, 230 Volts, including drivers, pressure di cast aluminium housing, prewired etc complete all as specified and directed. The fitting shalll conform to cat No - CORALPT35WLED757PSYMTOPC of Havells or Equivalent from Philips/Bajaj/Crompton

S & F in repairs decorative 20 Watts LED Post Top Lantern, 230 Volts, including drivers, pressure di cast aluminium housing, prewired etc complete all as specified and directed. The fitting shalll conform to cat No - RUBYT25WLED757PSYMTOPC of Havells or Equivalent from Crompton/Bajaj

S & F in repair/replacement of LED Driver 60 to 70 Watts Suitable for street light fitting, driver Shall Conform to Cat no X075C070V107FNY1BO of Crompton or Equivalent from Havells /Bajaj

S & F in repair/replacement of LED Driver 30 to 40 Watts Suitable for street light fitting, driver Shall Conform to Cat no S0DQL1-54-700-40Wof Crompton or Equivalent from Havells /Bajaj

Supply and fixing in replacement of MCCB 400 Amps 35 KA, 3 Pole including lugs,nut, bolts. washers testing etc complete all as specified and directed.

-Ditto- all as per item ser No 112.00 above but MCCB 250 Amps 35 KA, 3 Pole etc complete all as specified and directed.

-Ditto- all as per item ser No 112.00 above but MCCB 100 Amps 25 KA, 3 Pole etc complete all as specified and directed.

M&L for straight through joint (HEAT SHRINKABLE TYPE KITS) for underground cable including joint kits and labour complete for making joints suitable for LT, XLPE/PILCA/PVC sheathed armoured heavy duty cable with aluminium conductor 3.5/4 core 25 to 50 Sqmm etc complete all as specified and directed.

-Ditto- all as per item No 115.00 here-in-before but 2/4 core 6 to 16 Sqmm size -do-

-Ditto- all as per item No 115.00 here-in-before but 3.5/4 core 70 to 95 Sqmm size -do-

-Ditto- all as per item No 115.00 here-in-before but 3.5/4 core 120 to 185 Sqmm size -do-

Supply& fixing in repairs of Chequered plate Fe 410-W(Gde-E- 250)A quality- for cable trenches, ladders including equal angle trench frames, including cutting as per requirement of site, square cut or notched (ordinary and counter sunk) forming holes, without any including providing handles

Supply& fixing in repairs for mild steel work confirming to Fe-290, GdeE-165 in stairs/ladders including stringes, treades, landing, balusters, hand rails etc complete all as specified and directed.

M & L for water level indicator for under ground Tanks of size 2.52 x 0.3 m made out of MS angle iron 25x25x4 mm MS flat iron of 4 mm thick, 150 mm dia MS oval shaped float ball assembly with required length of stranded steel rope 10 mm dia, pulley, MS indicator and slot and accessories required for smooth functioning and applying black bituminous paint and making letter and figure with black/white paint to the level indicator over black painted back ground surface including taking down old indicator assembly etc complete all as specified and directed.

Removal of filter media complete from mild steel shell including PVC strainer of 10000 GPH from pressure filter plant for replacement of gravels/ sand and disposing of unserviceable materials to a distance not exc. 50 mtr etc complete all as specified and directed.

Scraping, descaling, cleaning internal surface of mild steel shell and applying two coats of paint with approved drining water grade paint and providing one coat of painting on external surface of shell alongwith pipe lines with anit - corrosive paint over a coat of red oxide zinc chrome primer with necessary preparation of surface etc complete all as specified and directed.

Supply and filling of size 25mm to 12 mm as filter media on iron removal plant etc complete all as specified and directed.

Supply and filling gravel of size 25mm to 12 mm as filter media on iron removal plant etc complete all as specified and directed. (Gravels shall be of river Barakar)

Supply and filling gravel of size 15 mm to 06 mm as filter media on iron removal plant etc complete all as specified as directed. (Gravels shall be of river Barakar)

Supply and filling gravel of size 06 mm to 03 mm as filter media on iron removal plant etc complete all as specified as directed. (Gravels shall be of river Barakar)

Supply and filling coarse sand of size 03 mm to 1.5 mm as filter media of iron removal plant etc complete all as specified and directed.

Supply and filling mesh sand of size 16/32 mm mesh as filter media of iron removal plant etc complete all as specified and directed. (Grevells shall be of river Barakar)

S & F PVC double nut type strainer etc complete all as specified and directed.

Taking up or down steel water tubing 15 mm bore and connections including cleaning and re-fixing if found serviceable including all new fittings or removal unsv pipe to store etc and refixing old steel tubing and connection in same position in wall, ceiling, floors etc after removal of blockage etc complete all as specified and directed.

-Ditto- all as per item No 131.00 above but 20mm bore

-Ditto- all as per item No 131.00 above but 25mm bore

-Ditto- all as per item No 131.00 above but 40mm bore

-Ditto- all as per item No 131.00 above but 50mm bore

M&L for preparation of two coat of synthetic enamel paint over & including a coat of red oxide zinc chrome primer on steel surface etc complete all as specified and directed. Note : A sum of Rs 1,02,910.00 towards sch of credit shall be deducated to arrive the contract sum.

M/s R J TRADING CO