REPAIR AND PAINTING OF VARIOUS TYPE OF ALMIRAH STEEL, LOCKERS AND OTHERS FURNITURE FOR OTM ACCN AT PANAGARH UNDER GE PANAGARH

Amount

STEEL/TP FURNITURE Removing/taking out carefully old unserviceable worn out/components/ parts of the following steel/TP furniture without disturbing the other parts and supply and fixing new parts with material and labour as specified and as appended below, made to shape & size all as per drawing and as directed and made to finishing to receive paint /polish and necessary welding if required, to bringout the new serviceable condition all as specified, directed and shown on drawing:-

FD-75(M) Chair CB Steel With Arm

seat frame and providing/fixing the new one of existing size made out of 1st class teak wood with and including duly re-caning with new plastic cane 2mm thick oval shape for general weaving and 4mm thick plastic cane for beading all around as show in drg. Wooden frame should be finished with black polish and fix in its original position with required screw(plastic cane type-I HDPE).

All as per BOQ Srl Item No 1.11 but for back frame

Handle made out of 1st class hard wood (Teak) well seasoned and of exisiting size and shape with required screw Wooden frame should be finished with black polish and fix in its original position with required screw (plastic cane type-I HDPE).

FD-75(M) Chair CB Steel Without Arm

seat frame and providing/fixing the new one of existing size made out of 1st class teak wood with and including duly re-caning with new plastic cane 2mm thick oval shape for general weaving and 4mm thick plastic cane for beading all around as show in drg. Wooden frame should be finished with black polish and fix in its original position with required screw(plastic cane type-I HDPE).

All as per BOQ Srl Item No 1.11 but for back frame

FD-1031 Almirah Steel Large

Taking out of broken door shutter from Almirah Large Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

Handle chromium plated heavy duty as approved by Engr-in-Charge/GE.

Lock 6 lever with deuplicate key ISI marked with round shape of MS key plate as approved by Engr-in-Charge/GE duly fixed as per drawing.

3 way locking device and providing/fixing the new one in its original postion as per drg.

Leg made out of MS sheet 1.00mm thick in its original position duly welded as per drg.

Shelf of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

FD-220 Charpoy GI Pipe with ply top

Ply-wood top of Size 1980X900X12mm thick, Commercial grade (07 ply) ISI Marked with beading all around, with and including 10 Nos galvanised countersunk nut andt Bolt of suitable size and length, 02 Nos washer for each nut and bolts as directed by Engr-in-Charge.

6mm thick GI Medium grade check nuts suitable for 32mm dia GI pipe all as specified and shown on drawings (Each check nut will be measured as single unit)

32 mm dia GI medium grade 3 way elbow ISI marked all as specified and shown on drg and directed by Engr-in-Charge (Each GI Elbow shall be measured as single unit)

Long Rail of GI Pipe 32mm Bore (dia) Medium Grade duly threaded both ends upto the required Length and fitted to frame of Charpoy i complete all as specified/as shown on Drawing/as directed (Make: TATA/JINDAL).

Making GI Charpoy Short Rail to be made out from Long Rail (Retrieved from item No 2.00 here-in-before), duly cut and threaded both ends upto the required length and fixing i, complete all as specified/as shown on Drawing/as directed.

Making GI CHARPOY LEG to be made out from LONG RAIL & SHORT RAIL (Retrieved from item No 2.00 & 3.00 here-in-before), duly cut and threaded one End including and providing 3mm thick Mild Steel Flat iron 55mm dia Welded to bottom of the Leg and fixing including treating with two coats of black paint over a Coat of Red Oxide Zine Chrome Primer, complete all as specified/as shown on Drawing/as directed.(Drg No FD-220).

FD- 1032 Almirah Steel Medium

Taking out of broken door shutter from Almirah Large Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

Handle chromium plated heavy duty as approved by Engr-in-Charge/GE.

Lock 6 lever with deuplicate key ISI marked with round shape of MS key plate as approved by Engr-in-Charge/GE duly fixed as per drawing.

3 way locking device and providing/fixing the new one in its original postion as per drg.

Leg made out of MS sheet 1.00mm thick in its original position duly welded as per drg.

Shelf of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

FD-1027 Form w/o back

Planks mde out of teak wood 25mm thick x255mm wide x1525mm long duly french polished and fixed with 9 Nos GI Bolts .

Legs made out of 25mm sq conduit (16 guage) of existing shape & size duly painted with black enamelled paint over a coat of primer.

Stiffners made out of 25mm sq conduit (16 guage) of existing shape & size duly painted with enamelled black colour over a coat of metal primer.

Rubber/ PVC shoes of existing shape & size.

FD-1029 Locker steel

Hasp & stappples of size 150 mm long chromium plated to the shutters of locker steel.

Handle of size 100 mm long 'D' Type chromium plated to the shutters of locker steel.

Hanging rod made out of 20mm dia chromium plated pipe 500mm long of locker steel.

FD-1004 Table office clerk steel

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with 19x4mm teak wood beading duly french polished all around the top.

Internal locks 40mm 4 lever with duplicate keys of approved quality.

Drawer of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

Repair to Drawer by welding/denting to bring in its original position existing size and shape. All as shown on drg.

Hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office clerk steel

FD- 1003 Table office officer steel

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

Internal drawer locks 40mm 4 lever with duplicate keys of approved quality.

hard rubber shoes of approved quality & tightly fitted at the bottom of legs

STEEL/TP FURNITURE Removing/taking out carefully old unserviceable worn out/components/ parts of the following steel/TP furniture without disturbing the other parts and supply and fixing new parts with material and labour as specified and as appended below, made to shape & size all as per drawing and as directed and made to finishing to receive paint /polish and necessary welding if required, to bringout the new serviceable condition all as specified, directed and shown on drawing:-

FD-1007 Table 900 x 600 x 760 mm Steel W/O/Drawer

Top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top.

Steel long rail of size : 25mm x 25mm x 1.6mm thick. All as shown on drg and directed by Engineer-in-Charge.

Leg made out of 25mm x 25mm x MS tube 1.6mm aell thickness. All as directed by Engineer-in-Charge and as shown on drg.

Stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

Short stiffner made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

FD-1009 Table 900 X900 X 760 mm steel

Top made out of 18/19 mm thick pre-laminated particle board (ISI Marked) exterior grade one side teak veneered finish and other side having balancing white lamination with 19 x 4 mm teakwood beading all around the top and polishing the wooden frame shall be with french polish(to the entire satisfaction subject to minimum two coats) including preparation of surfaces by scrapping /smoothing the surface all specified and shown on drawing .

Electric welding to the broken /dislocated 25 x 25 mm square tube rails of tables 900 x900x 760 mm steel , length of welding exceeding 2.5 cm but not exceeding 5 cm ( each spots measured separately) thickness of metal to be welded not exceeding 6 mm , complete all as directed.

Rubber shoes off approved quality and tightly fitted and the bottom of legs all as specified and shown on drawing

FD/MAP-II/01 Charpoy Hard Top MAP

Ply-wood top of Size 1980X900X12mm thick, Commercial grade (07 ply) ISI Marked with beading all around, with and including 10 Nos galvanised countersunk nut andt Bolt of suitable size and length, 02 Nos washer for each nut and bolts as directed by Engr-in-Charge.

PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

FD-1038 Rack Steel 6 Tier (closed type)

Back to rack steel closed type made of MS Sheet of 1 mm thick of eixsting shape and size and making functional.

Sides of rack steel closed type made of 1 mm thick MS Sheet in its original position as per drg & making functional

Shelves of rack steel closed type made of 1 mm thick MS Sheet in its originnal position as per drg & making functional

MS angle iron of rack steel closed type MS angle iron to rack steel closed type in its originzl position as per drg & making functional

FD-165(M) Table dining ORs

Top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top. Top will be covered with Almn sheet 20 gauge.

Steel long rail of size : 25mm x 25mm x 1.6mm thick, 1575mm long. All as shown on drg and directed by Engineer-in-Charge.

Leg made out of 25mm x 25mm x MS tube 1.6mm well thickness. All as directed by Engineer-in-Charge and as shown on drg.

Stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

Stiffner Top and S & F new stiffner top made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

FD- 1023 Side rack w/3 tray steel

Repair of side rack with 3 tray Steel by means of denting ,welding & scrapping wherever required making the frame in its original position and making functionel all as per drg and directed by engr- in- charge.

MS angle iron to side rack with 3 tray steel closed type in its originzl position as per drg & making functional

Shelves made of 1 mm thick MS Sheet in its originnal position as per drg & making functional

FD/E6/MAP/12 Chair Writing Steel.

Seat made of 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

Back made of 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

Hand rest made of black integral skin polyurethene with 75-85 shore 'A' Hardness & Reinforced with MS insrest. It shall be scratch and wheather Resistant Size 210mm (Inner) and 230mm (Outer)

FD-388(R) Charpoy IP Folding

Making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

FD-/ MAP/ II/07 Charpoy IP Square Tube

Ply-wood top of Size 1980X900X12mm thick, Commercial grade (07 ply) ISI Marked with beading all around, with and including 10 Nos galvanised countersunk nut andt Bolt of suitable size and length, 02 Nos washer for each nut and bolts as directed by Engr-in-Charge.

PVC Shoes. All as directed by Engineer-in-Charge and shown on drg.

STEEL/TP FURNITURE Removing/taking out carefully old unserviceable worn out/components/ parts of the following steel/TP furniture without disturbing the other parts and supply and fixing new parts with material and labour as specified and as appended below, made to shape & size all as per drawing and as directed and made to finishing to receive paint /polish and necessary welding if required, to bringout the new serviceable condition all as specified, directed and shown on drawing:-

FD-1043 Trestle Store Room Steel

Repair of Trestle Store Room Steel by means of denting ,welding & scrapping wherever required making the frame in its original position and making functionel all as per drg and directed by engr- in- charge.

TP Chair Auditorium

Arm rest of Chair Auditorium of Make- Zuari, Model No ZAC-102 and making functional.

Tightening of loosen side pannel by the help of removing old fastener and inserting new fastener of required size and tighten them.

Tightning of loosen back of chair Auditorium by inserting new Nut, bolt & washer of size 6 mm dia, 65 mm long.

Material & labour for preparing old painted steel surfaces by removing dents and bends, clipping, welding the damaged sheet and filling with putty and cleaning the surface to smooth to any description and of any girth and applying two coat of synthetic enamel paint 1st Quality OG/SMOKE GRAY/BLACK OR AS APPROVED by GE paint both inside and outside (outside only in case of round/square pipe/tube) by spray painting all as specified in particular specification and as shown on drawing and as directed by Engineer-in-Charge for the following articles of Steel furniture/TP furniture :- (Note : Second coat will be done after complete dried up of 1st coat as and when ordered and approval of 1st coat from GE

FD-75(M) Chair CB Steel With Arm

FD-75(M) Chair CB Steel Without Arm

FD-1031 Almirah Steel Large

FD- 1032 Almirah Steel Medium

FD-1029 Locker steel

FD-1004 Table office clerk steel

FD- 1003 Table office officer steel

FD-1007 Table 900 x 600 x 760 mm Steel W/O/Drawe

FD-1009 Table 900 X900 X 760 mm steel

FD/MAP-II/01 Charpoy Hard Top MAP

FD-1038 Rack Steel 6 Tier (closed type)

FD-39 FMN Set /Frame for bed/charpoy

FD-165(M) Table dining ORs

FD- 1023 Side rack w/3 tray steel

FD/E6/MAP/12 Chair Writing Steel.

FD-388(R) Charpoy IP Folding

FD-/ MAP/ II/07 Charpoy IP Square Tube

FD-1043 Trestle Store Room Steel.

WOODEN FURNITURE Removing/taking out carefully old unserviceable worn out/components parts of the following wooden furniture without disturbing the other parts and supply and fixing with new parts as specified and as appended below, made to shape & size all as per drawing and as directed and M&L of the same as listed below with new materials/components, made to finishing to receive paint /polish to bringout the new serviceable condition all as specified, directed and shown on drawing:-

FD-229 Repair/Re-canning of chair Easy

Front Legs made out of 1st class HW well seasoned (Teak)

Front rail of seat frame (Hole should be 12.5mm apart of each other) made out of 1st class HW well seasoned (Teak)

Side Rail of seat frame (Hole should be 12.5mm apart of each other) made out of 1st class HW well seasoned (Teak)

Back Rail of seat frame (Hole should be 12.5mm apart of each other) made out of 1st class HW well seasoned (Teak)

Arm Rest made out of 1st class HW well seasoned (Teak)

weaving with 2 mm thick new white plastic cane oval shape Godrej pattern and beading with 4mm thick new white plastic cane make Ajay /premier as approval by GE and providing new hard rubber shoes on legs below of chair Easy.

FD-99(M) Board Notice 1200x900

Door glass of 4 mm thick of existing shape and size and making functional

Door shutter 2 way of existing shape and size and making functional

Baize green cloth of existing shape and size and making functional

Soft wood board 19 mm thick of existing shape and size and making functional

Wooden frame made of hard seasoned teak wood of existing shape and size and making functional

FD/MAP-II/03 Table dining 6 Pers (MAP )

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

Legs of size 750x45x90mm made out of 1st class well seasoned teakwood.

Long rail of size 1500 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

short rail of size 900 X 45 X 90 MM made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

MS Right angle of size 150 x 30 x 5 mm with mild steel screws duly painted with black enamelled paint over a coat of primer. complete all as directed & shown on drg.

PVC Shoes.

FD/MAP-II/03 Table dining 4 Pers (MAP )

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

Legs of size 750x45x90mm made out of 1st class well seasoned teakwood.

Long rail of size 1500 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

short rail of size 900 X 45 X 90 MM made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

MS Right angle of size 150 x 30 x 5 mm with mild steel screws duly painted with black enamelled paint over a coat of primer. complete all as directed & shown on drg.

PVC Shoes.

FD/MAP/II/05 Repair of Chair Dinning

PVC seat 4mm existing size in its original position all as shown on drg and directed by Engr-in-Charge.

Front Legs made out of 1st class HW well seasoned (Teak)

Rear Legs made out of 1st class HW well seasoned (Teak)

Front rail of seat frame made out of 1st class HW well seasoned (Teak)

Side Rail made out of 1st class HW well seasoned (Teak)

Back Rail made out of 1st class HW well seasoned (Teak)

Short stiffener made out of 1st class HW well seasoned (Teak)

Back rest batten made out of 1st class HW well seasoned (Teak)

FD-284 Table 900x600x760mm without drawer/with drawer FD- (FD-42(m) ,FD-41(m) FD-291, FD-284,FD-283)

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

Legs (size 740x60x30mm) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

Long rails (740x25x65mm) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

Side rails (size 440x25x65mm) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

Side stiffiner (740x25x130mm) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg for FD/41/FD-284

Drawer made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

PVC Shoes as directed by Engineer-in-Charge and shown on drg.

FD-88(M) Table 900x900x760mm wdn

Top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

Legs of size (60x35x760mm long) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

Top rails of size (75x25x900mm long) made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg

PVC Shoes

FD-281 Sofa set 3 + 1 Seater

Front Legs made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Rear legs made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Front rail of sofa set 3 seater, made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Back rail of sofa set 3 seater, made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Arm Rest made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Back wdn bearers of sofa set 3 seater, made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Bottom wdn bearers of sofa set 3 seater, made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

Sofa cushion 100 mm thick x 40 density of size 530x560mm covered with new tapestry cloth duly stitched.Make: Kurlon/sleep well

FD-86 (M) Trestle Store Room Wooden.

2nd class Hard wood (SAL) legs of size 405x100x100mm

2nd class Hard wood (SAL)Top Batten (Middle of size 2400x60x100mm)

2nd class Hard wood (SAL) Batten (Side) of size 2440x100x100mm

2nd class Hard wood (SAL) Batten (Short) of size 600x100x60mm

Repair to loose wooden trestle, Providing clamp piece of size 300mm x 40 mm x 5mm `L` shape with 6 nos screw including painting with black paint.

Preparation of surface of wooden trestle of any description and treated with two coats of creosote oil all as specified.

WOODEN FURNITURE Removing/taking out carefully old unserviceable worn out/components parts of the following wooden furniture without disturbing the other parts and supply and fixing with new parts as specified and as appended below, made to shape & size all as per drawing and as directed and M&L of the same as listed below with new materials/components, made to finishing to receive paint /polish to bringout the new serviceable condition all as specified, directed and shown on drawing:-

DB-4120 Table office clerk wooden

Top made out of 18/19 mm thick Prelaminated particle board teak veneered finish and provided with beading of teak wood size 19x4mm alround the top fixed with 20mm pannel pin complete all as directed and as shown on drawing

Drawers made out of Ist class teak wood well seasoned and 6mm thick ply wood (5 ply) commercial BWR gde complete all as directed and as shown on drawing

Stainless steel handle 75mm of approved quality complete as directed

Stiffners made out of Ist class teak wood well seasoned complete all as directed and as shown on drawing

Short stiffner of existing shape and size made of 1st class hard seasoned teak wood free from knots duly french polished..

Long rails made of 1st class hard seasoned teak wood free from knots duly french polished.

Short rails made of 1st class hard seasoned teak wood free from knots duly french polished.

Legs of existing shape and size made of 1st class hard seasoned teak wood free from knots duly french polished.

FD-279 Chair Dinning.

Front Legs made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Rear Legs made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Front rail of seat frame (Hole should be 12.5mm apart of each other) made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Side Rail made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Back Rail made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Short stiffener made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Back rest batten made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Remove the existing canning and supply and weave with 2mm thick new white plastic cane oval shape godrej patern and beading with 4mm thick new white plastic cane as apporeved by GE.

Rubber shoes of apporoved quality & fixed at the bottom of legs of Chair Dining

DB-3954 Chair CBA Office

Front leg.made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Rear leg.made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Side rail made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Front rail made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Back rail made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Back rest batten horizontal made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Long stiffener made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Short stiffener made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

Removing the all worn out plastic cane from chair and providing and re-caning of the same with new white plastic cane 2mm thick half round oval shape for general weaving and 4mm thick cane plastic for beading work all around as shown in drg (Plastic Cane Type -I HDPE)

Material and Labour for Complete removal of total existing painting/polish and applying two coats of high gloss polyurethane enamel paint (Nerolac:Wonder Wood Coatings 1K PU Glossy/ Asian Paints:Wood Finishes Wood Tech Melamyne Glossy/ J&N Paints:Brolac Hi Gloss Polyurethane Enamel/ Berger Paints: Wood Finishes Imperia Luxuary Polyurathene High Gloss)by spray painting method over and including a coat of pink primer and prepration of surfaces Complete all as specified and as directed for the following furnitures :-

FD-229 chair Easy

FD-99(M) Board Notice 1200x900

FD/MAP-II/03 Table dining 6 Pers (MAP )

FD/MAP-II/03 Table dining 4 Pers (MAP )

FD/MAP/II/05 Repair of Chair Dinning

FD-284 Table 900x600x760mm without drawer/with drawer FD- (FD-42(m) ,FD-41(m) FD-291, FD-284,FD-283)

FD-88(M) Table 900x900x760mm wdn

FD-281 Sofa set 3 + 1 Seater .

DB-4120 Table office clerk wooden

FD-279 Chair Dinning.

DB-3954 Chair CBA Office

BABY ENGINEERING ELECTRICAL MECHANICAL STORES (BID ID -3151648)

ANSH CONSTRUCTION (BID ID -3151713)

Jaibalaji Enterprise (BID ID -3152684)

BISWAS ENTERPRISE (BID ID -3152786)