PROVN OF PARKING SHED, ALUMINIUM PARTITION AND MISC B/R WORKS IN TECH AREA AT AF STN GWALIOR

Amount

Demolition of cement concrete/bituminous surface incl cutting edges as directed with mechanical cutter in ground floors and pavings exc 15 cm thickness (below or above ground level) and removing debries out of premisis all as specified and directed.

Excavating in post holes (or similar holes) in soft loose soil n.exc 0.50 cum each and removing excavated soil out off the promises complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, vertical post and fastenings and framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

M&L for PCC (1:4:8) type D-2(using 40 mm graded stone aggregate) in foundations, filling post holes for vertical MS steel pole including necessary formwork complete all as specified and directed.

M&L for PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) in foundations filling, including footings and filling post holes for post including necessary formwork complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F mild steel bolt (machine) made with hexagonal of square head at one end and screwed end to be fitted washer hexagonal or square not exceeding 5cm long complete all as specified and directed.

S&F Plates (plain or chequered) channels, cut or notched (ordinary and counter sunk) forming holes, welded/bolted to steet frame/truss all as specified and directed.

M&L preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer over 10m width or girth complete all as specified and directed.

M&L for Hand rails, half round or other steel section or wind ties for roof including securing bolts complete all as specified and directed.

M&L preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer n. exc 10m width or girth complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated soil to a dist n.exc 50m and depositing where directed at a level n.exc.1.5m ht from the starting point.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregates as in sub base complete all as specified and directed.

M&L for 60mm thick factory made cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc, over and including 50mm thick compacted bed of fine sand/stone dust and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. Make: ISI Marked as Approved by GE.

M&L for PCC 1:2:4 as in floor finishes, ramp, kerbs, benching rounded or chamfered on edges complete all as specified and directed.

M&L for factory made kerb stone, PCC 1:2:4 type B-O (using 12.5 mm graded crushed stone aggregate), of cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including neceassary excavation work and making drainage opening wherever required complete all as specified and directed.

S&F Powder coated aluminium frame for door, window, ventilators and partitions with extruded built up standard tubular sections with necessary jointing aluminium cleats using C.P./ stainless steel screws, all as specified and directed by Engr-in-Charge.

S&F Powder coated aluminium door shutters with extruded built up standard tubular sections using aluminium sec not less than 2.00 mm thick, (shutter with styles 85mmX44.45mm, top rails 83.5mmX44.45mm , intermediate rail 83.5mmx44.45mm, bottom rail 114.3mmx44.5mm) with aluminium beading and rubber neoprene paking for fixing glass, each shutter comprising of aluminium powder coared builder hardware( like 03 Nos hinges, 02 Nos 200mm Handle, 01 Nos 16mm dia 300mm long sliding door bolt and 01 Nos 150mm tower bolt) using C.P./ stainless steel screws, all as specified and directed by Engr-in-Charge.

S&F Powder coated aluminium sliding windows shutters with extruded built up standard tubular sections (using aluminium sec not less than 1.5mm thick), with aluminium beading and rubber neoprene paking for fixing glass and, 02 Nos sliding rollers at bottom, PVC locking arrangement to each shutter using C.P./ stainless steel screws, all as specified and directed by Engr-in-Charge.

Taking down chowkats with shutters (without taking off shutters from the frames) of any description n.exc 1.5 Sqm each complete all as specified & directed

Taking down chowkats with shutters (without taking off shutters from the frames) of any description exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified & directed

S&F 5mm thick tinted glass, and glazing in square/rectangular to aluminium frame in each pane complete all as specified and directed.

S&F 4mm thick ACP (Aluminum composite pannel) coloured sheet with 0.25mm thick of aluminium coil, sandwitch panel for fixing to aluminum doors /partitons complete all as specified and directed.

S&F 4mm thick tinted glass, and glazing in square/rectangular to aluminium frame in each pane complete all as specified and directed.

S&F 18/19mm thick HDHMR (High Density high moisture resistant) prelaminated board both sides with decorative choice laminations, fixed with screws & favicol where reqd as in cubical desk and cabinets including making holes with decorative covers for wires where ever required fixed to Aluminum partition.

S&F Stainless steel handles 100mm size for cabinets shutters as per specifications and as directed by the Engr in charge.

S & F auto closing hinges 35mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinets shutters.

S&F stain less steel Sliding channels (ISI Mark) for Computer Keyboard and drawers.

M&L for 2 lever Brass Locks for cupboard, grade I, size 50 mm Make: Godrej, Harrison, Link.

Demollition of cement concrete ( unreinforced) including floor tile and screed bed ground floors and pavings n. exc 15 cm thick below or above G.L complete all as specified and directed .

M&L for 25 mm thick PCC (1:2:4) type B0 (12.5 mm graded stone agg) as in sub base of flooring complete all as specified and directed.

M&L for 8 to 10mm thick double charged vitrified ceramic coloured tiles (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over 15mm th screed bed in CM 1:6 complete all as specified and directed.

All as per item No 33 here-in-before but as in skirting/dado but 10mm thick cement plaster1:4 as backing coat

M&L for Preparation of old decorated surface of wall include scrapping down layers, smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, including filling the cracks and depressions and applying two coat of distemper oil emulsion with Roller white or tinted as approved complete all as specified and directed.

Ditto as per item No 35 here-in-before but one coat of white wash on ceiling surface

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified and directed.

S&F aluminium (extruded section) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg compelte all as specified and directed.

S&F 4mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic ) decorative finish fixed with screws to snap grid including pre powder coated GI frame with suspension system (Grid) comprising of T section 25mmx32.5mm x1.6mm size as main runners and wall angle to placed along the wall at desired level of the False ceiling , 4mm dia GI suspender of suitable size and dash fastners to be provided at desired distance including removing and refixing re-fixing false ceiling lights, electric fans fittings/fixture etc. complete all as specified and directed.

S&F Stainless steel curtain rod standard size 25mm dia and 0.75mm thickness fixed to wall including SS brackets fixed with rawal plug and zinc CP screws complete all as specified and directed.

S&F Stainless steel decorative choice end globe for fixing with curtain rods complete all as specified and directed.

M&L for MS framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars, barred iron doors ladders, framed balusters, walk ways, railings, cooler stand, wind tie etc

Cutting holes in brick walls / RCC column and inserting holdfasts and making good dismantled portion in cement concrete 1:2:4 Type B-0 and plaster in CM 1:3 incl necessary distempering to match with the adjacent surface as specified and directed.

M/S Rajeev Construction

GWALIOR TRADE LINK

SHRI RAM CONSTRUCTION

m/s vikash Engineers