Constn of District Disease Lab

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. (HSR 6.6)

Dismantling Brick Wrok, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5) (b) In cement

Dismantling cement conglomerate/terrazzo-floors 25 mm to 50 mm thick without concrete base. (HSR 8.26)

Scrapping (HSR 8.32) (a) White wash and colour wash

Scrapping (HSR 8.32) (c) Cement plaster

Cement concrete 1:8:16 with brick ballast 40mm nominal size in foundation and plinth (HSR 10.26).

Providing & laying 50mm thick ISI marked interlocking paver blocks (conforming to IS 15658 2006) of all shapes and colours in design mix cement M-30 over a bed on 25mm thick fine sand complete in all respect. (HSR 10.157)

First calss brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2).

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR 14.10)

Providing and fixing 1st auality ceramic glazed wall tiles confirming to I.S 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except gurgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in whte cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300x450mm

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Painting two coats with readymixed paint in all shades on old wood work to give an even shade including rubbing down old paint (HSR 16.6)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79) (b) 1st quality

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Providing and fixing aluminium work for doors, windows, ventilators and partitions wirh extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with rawplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panneling C.P. brass/ stainless steel screws etc. complete. Shutters of doors, windows & ventilator i/c providing and fixing hings/ pivots and making provision for fixing of fitting wherever required i/c the cost of PBC/ neoprene gasket required i/c aluminium fitting i.e. aluminium Kun. (HSR 17.96)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or garded wood particle board confirming to IS; 12823 grage 1 type II in panneling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete. (HSR 17.97) (b) Pre-laminated particle board with decorative lamination on both side

Providing and fixing glazing in aluminium door windows, ventilator shutter and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shallbe paid in basic items). (HSR 17.98) (b) With float glass panes of 5.0mm thickness

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, grating frames, window guards, iron doors, openable or fixed staircase or parapet or any other type of railing, gates and tree guards etc. including cost of screws and welding rods or bolts and nuts complete fixed in position.(HSR 18.12)

Providing and fixing in position best Indian make vitreous Chinaware Sinks with complete fittings as fully described in Item No.30.51 above (HSR 30.52) White (a) Size 600 mm x 450 mm x 200 mm

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). (HSR 30.75) (a) Bib cock long body

Earth work (Tibba sand) in the campus involving exacavation of earth in all type of soil or rocks where earth is brought from out side from 5 Km and above lead & lift to the site of work including laying in 25cm layers for compacttion including cost of watering and rolling and compensation of earth taken from private land, dressing of banks and side slopes to given site levels and templates after breaking of clods. The complete rate quoted by the contractor shall take in to account all allowances for labour, hardness, witness and all kinds of carriage, loading, unloading, total lead and lift of soil involved to the entire satisfaction of Engineer-in-Charge confirming fully to Haryana PWD specification 1990 1st addition including subsequent agenda and corrigenda issued from time to time till the date of final payment (N.S.)

Sh. Nikunj Bansal