REPAIR MAINT OF OFFICERS MESS, SINGLE LIVING OFFICERS ACCN, SERVANT QUARTERS, REPAIR/ MAINT TO SWR PIPE, SEWAGE SYSTEM, RAISING MANHOLES, OTHER MISC B/R WORKS IN OMQ AREA

Amount

SCHEDULE A BOQ

Note for all items of this BOQ :- (i) Based on the complaints recieved through online from User's, a complaint slip shall be prepared and handed over to contractor on day to day basis to rectify the defects. (ii) The User's shall be approached by showing the identity of trades man and ascertain the nature and location of the complaints/ defects. (iii) Every complaints shall be addressed with utmost user satisfaction. (iv) The tradesman who is engaging for complaints should be skilled and well equipped with requisite tools & plants. (v) After competion of every complaints, User's satisfactory remarks shall be obtained. (vi) If the user give unsatisfactory remarks, the complaint shall be re-attended till the reciept of satisfactory report from the User at own risk and cost of contractor and nothing extra shall be admissible on this account.

M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 complete all as specified and as directed.

Repair of leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ washbasin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe embeded in floor in bathroom or kitchen making good to the damage portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed by Engineer-in-Charge. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit

Repair of leakage/seepage from the wall/ door bend /door tee/ 'Y' junction/ 'T' Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damage soil waste pipes or fittings of any shape, specification and size, making good to the damage portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and matching to existing wall complete to avoid the leakage/ seepage at the site of work as directed and specifie by the Engineer -in- charge Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit

Note for item No 3 & 4 :- (a) Find out main cause of leakage and take necessary steps to resolve / rectify.

(b) Replace existing tiles in case leakage through NT/FT.

(c) The rate also include provision of new NT/FT.

(d) The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as direct by the manufacturer specification.

M&L Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal off to outside MD land complete all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including backing coat of 15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal of to outside MD land complete all as specified and directed.

Note for item No 9 & 10 :- (i) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (ii) The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

M&L Taking down & re fixing high or low level flushing cistren 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of rubber washers, stopping of leakage etc complete all as specified and as directed

M&L PVC connection 15 mm size with PTMT nuts of length 450 mm including taking existing one complete all as specified and directed.

M&L WHB, vitereous china (flate back or angle back type) of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe Complete including taking down existing one complete all as specified and directed.

M&L in repairs Chromium plated wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed. Make:- QT F2002401 of CERA or equivalent in Parryware /Hindware / ESS-ESS all as specified and as directed.

M&L Corner Glass shelf assembly including taking existing one complete complete all as specified and directed. (Make : CAT Part No-F5005102 of CERA series or equivalent make of Parriware /Hindware all as specified and as directed.

M&L Towel Ring round including taking existing one complete as directed by Engr-in-charge. Make: (Make : CAT Part No-F5002105 of CERA series or equivalent make of hindware / parriware all as specified and as directed.

S&F in repair CP Soap dish CAT Part No-F5003106 of CERA or equivalent make of Parriware /Hindware all as specified and as directed.

S&F Plastic water closet seat for EWC with flat bottom and cover and mild steel chromium plated or alluminised hinging device fixing Including taking down existing one complete all as specified and as directed by Engineer-in-Charge.

S&F PVC body cabinet mirror of size 500 X 400 MM of approved design and pattern Including taking down existing one complete all as specified and as directed by Engineer-in-Charge . (Make: Cat Part No 556 of Prayag or its equivelent in ESSCO/ Kohler as approved by GE

S&F PVC Dual flush ceramic colour, low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements Including taking down existing one complete all as specified and as directed by Engineer-in-Charge Cat Part No 21029 of hindware or equivalent

S&F Wall mounted Shower Arms 200mm long flat shape for wall mounted shower with flange including taking down complete all as specified and directed (Make :CAT Part No-F7040102 of CERA or equivalent make of parriware /hindware..

S&F in repairs Overhead Shower 95 mm (4”) dia with 3 flow Round Shape 3 Flow complete all as specified and as directed. (Make :CAT Part No- F7020302AB of CERA or equivalent make of parriware /hindware.

S&F PVC (SWR) 75mm bore junction vent cowl including taking down existing one complete all as specified and as directed by Engineer-in-Charge

M&L PVC (SWR) 110mm junction vent cowl all as specified including taking down existing one complete all as specified and as directed.

S&F 600 x 450 mm bevelled edge mirror fixed with 04 Nos Stainless steel studs including taking down existing one complete all as specified and as directed.

M&L False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load upto 8.1 Kg/Sqcm with 4mm thick designer ceiling board Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster on brick or stone walls, or concrete or ceilings, roof in any position . cincluding raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and fair complete all as specifiied and directed.

M&L rendering 5mm thick on ceilling of concrete surfaces in CM 1:3 complete all as specified and as directed finished even and smooth without using extra cement complete all as specified and directed.

M & L preparation of new plastered or unplastered surface of ceilling, and applying two coats of white wash on ceilings complete all as specified and directed

M & L preparation of new or plastered or unplastered surface of wall and applying two coats of cement based paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M&L rendering 15mm thick in cement plaster 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished even and smooth without using extra cement complete all as specified and as directed

M & L preparation of new plastered or unplastered surface of wall and applying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specified and as directed.

S & F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved. Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S & F Particle board plywood 18/19 mm thick interior fixed with screw to timber frame including taking down existing one work complete all as specified and directed

S & F Stainless steel thali basket of size 600x 500x 100mm Including taking down the existing one complete all as specified and directed Make : Butterfly or equivalent make as per list of makes)

S & F Stainless steel cutlery basket of size 530 x 505 x 100 mm Including taking down the existing one complete all as specified and directed Make : Butterfly or equivalent make as per list of makes)

S & F Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen Including taking down the existing one complete all as specified and directed (Make : BIR SS or equivalent make as per list of makes)

S & F Magnetic catches with 8mm dia steel ball and brass body and striking plate including letting in & Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S & F Stainless steel plain basket of size 530 x 505 x 100mm Including taking down the existing one complete. Make : Butterfly or equivalent make as per list of makes

S & F Stainless steel bottle basket of size 200x 508x 431mm including taking down complete all as specified and directed. Make : Butterfly or equivalent make as per list of makes

S & F Stainless steel telescopic slider of 500 mm of approved pattern and make suitable for drawer in base unit of modular kitchen including taking down the existing one complete all as specified and directed.

S & F Brass continuous(Piano)hinge 30mm width of flap, bright finish of electrolyte Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S & F Stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen Including taking down the existing one complete (Make : Spykar or equivalent make as per list of makes)

S & F Brass 4 lever cupboards locks grade I size 65mm Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S & F 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished Including taking down existing one complete all in repair as specified and as directed by Engneer-in-Charge

S & F 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings Including taking down existing one complete all as specified and as directed by Engneer-in-Charge

S & F Mild steel powder coated brackets for holding the drapory rod and fixed to wall with MS screw Including taking down existing one complete all as specified and as directed

S & F Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod Including taking down existing one complete all as specified and as directed

S & F PVC body cabinet mirror of size 500 X 400 MM of approved design and pattern Including taking down existing one complete all as specified and as directed by Engineer-in-Charge . (Make: Cat Part No 556 of Prayag or its equivelent in ESSCO/ Kohler as approved by GE

M & L Second class hard wood plain fillets square or rectangular in section exc 3Sqcm n.exc 6 Scqm wrought secure with screws including taking down existing one complete all as specified and as directed.

S & F 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, including taking down existing pipe of any description complete to walls, ceilings or in floors etc. all as specified and directed.

Note for item No 53 :- (a) The unit rate shall be include for taking down existing GI pipe and connections and all fittings as directed.

(b) The unit rate shall be include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

S & F 20mm outer dia of pipes PPR gate valves (brass insert) as per requirement of sites incl taking down existing one complete all as specified and directed.

Supply and fixing in repairs factory made UPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. and provided with Clear Glass of Saint Gobain / Modiguard make with thickness of 4mm and stainless steel wire cloth of 0.19mm nominal dia. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Taking down Chowkhats or frames exc. 1.5 sqm. but nexc 4 sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down Shutters of anydescription exc 1sqm. But nexc 2 sqm each complete all as specified and directed.

M & L Mild steel work in framed work such as grills and similar work including framed guard bars, barred iron doors, ladders, framed balusters etc., including of fixing of sheet steel or other covering to doors etc., to be prepared for hanging /sliding with or including either hooks or hinges or steel hanging door fittings etc., confirming to Fe 410-0 or Fe 310-0 work complete including Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Supply and fixing butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and directed.

S&F 200 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and directed.

S & F in repairs MS Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F Factory made 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and directed.

M&L for applying Two coats of synthetic enamel paint over a coat of pink primer over new wooden surface of any description over 10 CM width or girth including preparation of new surfaces complete all as specified and directed. .

Note for item No 67:- (a) All synthetic enamel paint, plastic emulsion paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

S&F in repairs Aluminium anodised, barrel tower bolts 200mm long of extruded section complete all as specified and directed.

S&F in repairs Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type), 300mm long and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repairs Floor door stopper 150mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair Mild Steel ordinary rat tail rod pattern springs, 300mm long including roller and roller plate complete all as specified and directed.

S & F Hasp and staple 75 MM size, safety type, aluminium anodised hinge pin including bolt to hinge plateand fixed with screws complete all as specified and directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm each pane complete all as specified and directed.

S&F in repair Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, 10cm and n exc 15cm long diameter of neck 5 to 10mm complete all as specified and directed.

Supply and fixing in repairs factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension,including Pinhead Glass with thickness of 4mm required for fixing & louvers strips, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in imension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed.

Demolition of cement Concrete in ground floors andpavings n exc 15 cm thickness(below or above ground level) complete all as specified & directed

M&L for 75 mm thick plinth protection in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or hamfered, put together with glue pinned at joints, supplied and fixed

M & L Bullnosed chequered cement concrete tiles 30cm x 30cm x 25mm thick machine pressed set jointed and pointed in neat cement slurry as in treads and cut and polished using grey cement and pigments over screed bed or bedding layer of mortar 15mm thick for laying floor fnishes in cement mortar (1:4) including taking down existing tiles complete all as specified and as directed by Engineer-in Charge. Note :- The manufacturer's test certificate and individual test certificate of tiles must be submitted for approval by the concered authority prior to installation

S&F Anodised aluminium frame for doors,windows, ventilators with one or morerebates including joining cleat forfixing etc. complete all as specified & directed

S&F Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each screws etc. anodised aluminum snap beading hinges,complete all as specified & directed

S & F 9 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & fixed with screws to timber/aluminium frame work complete all as specified and directed.

M&L 5.5mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm or with aluminium beading and glass not exc 0.5 sqm each pane complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair 40mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed.

Blocking up the entry of septic tank of the following capacities and pumping out effluent dirty liquid and solid sludge from septic tank including intercepting chambers etc up to bottom collecting sludge and cleaning the septic tank line for reuse and removing the sludge out side to MoD Land and depositing the sludge where directed by local municipal authorities complete all as specified.

200 users septic tank

100 users septic tank

50 users septic tank

25 users septic tank

10 users septic tank

Note for item No 96 to 101 :- The unit rate quoted is deemed to be inclusive for the following :-

(a) Solid sludge means bulky mass of sludge which remains at the bottom of septic tank/soakage well after pumping out/taking out sludge water.

(b) Contractors are advised to ascertain the place suitable/earmarked for disposal of sludge/sewage water from local municipality or area controlling authority before quoting their rates. Disposal of waste at suitable place shall be sole responsibility of contractors and no representation or objection in this regard will be entertained at later stage.

(c) The rate included for excavation of borrow pits for burying of removed sludge under the ground, making good the excavated earth to a true surfaces.

(d) Removing of accumulated earth around septic tank up to 3 m of any width and depth up to 30 cm. cleaning/cutting the grass around septic tank up to 3 m and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

(e) The complaints to be rectified within SIX hours on same day. The Delay in rectification of complaint more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(f) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/EIC.

S & F in repairs PVC (SWR) branch piece single (single Y) 75mm bore equal or unequal provided with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) branch piece single (single Y) 110mm bore equal or unequal provided with access door complete all as specified and as directed.

S & F in repairsPVC (SWR) 75mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) 110mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed.

M&L cutting salt-glazed stoneware drain pipe 150mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

M&L cutting salt-glazed stoneware drain pipe 200 mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

M&L cutting salt-glazed stoneware drain pipe 100 mm bore in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 and making good, complete all as specified and directed.

S & F in repairs stack clamps made out of 50 mm x 3 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 110 mm bore pipes complete all as specified and directed.

M&L Cleaning/ clearing of sewage line (including manholes) 150 mm to 300 mm dia main line from 1st manhole onwards bore of any description, underground at any depth, removing any type of blockage including desludging, descaling & decoking of drain as well as manholes with combined high pressure water jetting cum suction (vaccum) type machine mounted on LCV/HCV /LMV/HMV and having facilities of high pressure vaccum and provn of hydraulic through high pressure thermo plastic fiber based water jetting hose and conical round shape nozzle pipe and flushing after cleaning including removing the same out side MD land and deposit where the place marked by the local municipality, all as directed by Engr-in-Charge

Note for item No 117 :- The unit rate is deemed to be included for Removing of accumulated earth at sides of drain of any width and depth up to 30 cm. cleaning/cutting the grass around 1 m from drain (both sides) and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level . Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

M& L Cleaning of blockage from nahani traps of bath/kitchen in ground floor and upper floors by taking out mud/sand complete all as specified and as directed.

All as per item No. 119 above but cleaning of blockage from Gully trap to 1st manholes in ground floors.

M & L Cleaning of blockages from water closets in ground floors/upper floor including re-fixing of lid of door bends etc in position after completion of job all as specified and as directed.

Note for item No 119 to 121 :- The unit quoted rate is deemed to be included for the following :-

(a) Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be made good carefully by filled up with moorum/red bajri well rammed and levelled.

(b) Safaiwala shall report to concerned JE /AGE B&R in service centre daily including Sunday and holiday and get the job card for carrying out the work. The Job card shall be returned to concerned JE/AGE duly signed by the users as a token of completion of job.

(c) Cleaning, removal of silts/wastage of organic or inorganic materials of Sewage line of 100mm to 450mm bore up to 1st manhole, in between manholes, GT Chamber, etc to maintain sewage system functional all working days including Sundays and holidays along with necessary T&P i.e flexible rods, cleaning pumps and safety kits etc.

(d) The complaints to be rectified within six hours on same day. The Delay in rectification of complaint more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(e) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/EIC.

M&L Vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistren and flushpipe) and including seat cover for pedestal pattern complete fixed including taking down existing damaged one complete as specified and as directed.

M&L Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete bedding fixed including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) 110mm bore P Trap including taking down existing one complete all as specified and as directed.

M&L PVC (SWR) 110mm bore S Trap including taking down existing one complete all as specified and as directed.

Material and Labour for Granite work (of any type) 18 to 20mm thick (table rubbed and polished including round edge) in steps, jambs, pillars, windowcills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in cm 1:4 including dimantling existing one complete all as specified and directed by Engineer-in-Charge. NOTE : The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe ,waste pipe etc (excluding flushing cistern and flush pipe ) complete all as specified and directed by Engineer-in-Charge .

S&F in repair Vitreous china urinal partition white of size 32.5 x 69 cm of Cat No 61001 of Hindware or equivalent in jaquar/cera ,fixed about 40cm above floor line, complete all as specified and directed by Engineer-in-Charge .

S&F in repairs Chromium plated Urinal spreader for fixing with 15mm dia pipe complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position complete all as specified and as directed.

M&L Precast RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces including formwork, set in cement mortar 1:4 complete all as specified and as directed.

S&F High strength corrosion resistant TMT bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified.

M&L110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing damaged PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L150 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing damaged PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall incuding taking down existing PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed.

M&L Salt-glazed stoneware drain pipes, 100mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe any size including damaged concrete in haunching/base etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 100 mm bore of pipe, complete all as specified and as directed.

S & F in repairs PVC (SWR) bends any radius 110 mm dia fixed to wall complete all as specified.

S & F in repairs PVC (SWR) bends any radius 75 mm dia fixed to wall complete all as specified.

M & L 100mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates), laid in 1:20 slope as in hardstanding/ path including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement including demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness and rubish material shall be disposal to out side MD land complete all as specified and as directed. Note :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

M&L Chequered cement concrete tiles 30cmx30cmx25mm thick machine pressed set jointed and pointed in neat cement slurry as in floors and cut and polished using grey cement and pigments over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) including demolition of existing tile complete all as specified and directed. Note : The manufacturer's test certificate for tiles must be submitted for approval by the concerned authority.

M & L cleaning of roof top of buildings by scrubbing out mosses, dirt, algae, leafs, uprooting of vegetation growth including roots on roof/parapet walls and accumulated silt deposited over the concrete roof surfaces including cleaning of all drain pipes to provide smooth flow of rain water and removal of the deposited materials upto a distance of 50 metres outside the periphery of the building under cleaning complete all as specified and as directed.

Excavation in trenches in foul position n.exc 1.5m width and n.exc 1.5 m depth and getting out in hard/dense soil complete all as specified and as directed

Excavation in trenches in foul position n.exc 1.5m width and deapth exc 1.5 m but not exc 3mtr and getting out in hard/dense soil, complete all as specified and as directed.

Note for Item No 149 & 150:- (a) Excavating either straight or curved on plan

(b) Clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres outside the periphery of the area under clearance except in the case of surface dressing which includes for all the foregoing except clearing away of trees

(c) Bailing out, pumping out or otherwise removing all water which may accumulate in the excavations

(d) Setting out the work profiles, etc. as well as for all tools and plant

(e) All materials and labour required protecting against risk of accidents, etc.

(f) Watching and lighting, whenever necessary.

(g) Forming (or leaving) ‘Dead men’ or ‘Tell tales’ in borrow pits and their removal after record of measurements where required

(h) Forming (or leaving) steps in sides of deep excavations and their removal or covering up, after record of measurements

(j) Excavation for insertion of planking and strutting where required

(k) Removing slips or falls in excavations

(l) Authorised battering or benching of excavations

(m) Slinging or supporting pipes, electric cables, etc. met with during excavation

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified.

Removal of excavated material to a distance exceeding 1.50 Km and not exceeding 5.00 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L Plain Cement Concrete (1:4:8) type D2 (using 40 mm graded stone aggregate)as in foundations, filling and mass concrete complete all as specified and as directed.

M&L Providing cement concrete type C1, 1:3:6 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed.

Extra for forming fair finished drain or channel of 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed.

M&L Rendering 15 mm thick in two layers on brick or concrete surfaces,first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and as directed.

Note for Item No 168 :- (a) Water proofing compound shall be measured and paid seperately.

(b) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

Supply Only integral water proofing compound complete all as specified and as directed. Make:-Dr. Fixit , Pidi Proof or equivalent.

M&L PCC (1:2:4) Type B1 (using 20 mm graded stone aggregate) as in coping including necessary form work finished fair and even surface without using extra cement including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and provision of new Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as specified and as directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and provision of new Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat complete all as specified and as directed.

M&L Preparation of plastered or un plastered old surfaces of walls, Chajja, balcony, facia etc. by brooming down or steel wire brushing scrapping down, smoke shoots moulds, mass efforescent salt, treating oil and greasy spots etc and applying one coat of cement based paint complete all as specified and directed.

Note for Item No 175 :- (i)Before applying cement based paint ,the surface shall be thouroughly wetted to control surface suction. The surface shall be moist but not dripping wet when the paint applied .Surfaces which readily absorb moisture shall be wetted in one operation not more than one hour before painting.Surfaces which absorb moisture slowly shall be wtted in at least two operations not less than 30 minutes apart.

(ii)To maintain a uniform mixture and to prevent segregation ,the paint shall be stirred frequently in the bucket.

(iii)Painting surfaces shall be cured as soon as paint has hardened so as not be to damaged by the spray about 12 hours after the applications.

(iv) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

(v)Paints shall be obtained direct from approved manufacturer or from their authorized agents only and brought to site in sealed containers. The paint so procured shall be of any approved make as per list of makes specified.

M&L Preparation of old painted steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint using mechanical means complete all as specified and directed.

Note for item No 181:- (a) All synthetic enamel paint, plastic emulsion paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

M & L removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet/Shaft portion , near pipes etc and applying acid treatment after removing roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed.

Note for item No 190 :- (a) Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding.

(b) Contractor shall provided safety gears to his workers at his own cost and safety precaution to avoid accidents.

M & L Preparation of old plastered surfaces of wall by using pressure washer, removal all dirt and dust and applying one coat of exterior emulsion apex paint complete all as specified and as directed.

Note for item No 193:- (a) The Exterior emulsion apex paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands and brought to site in sealed containers. The paint so procured shall be of first quality

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

Demolition of Brickwork/stone boulder masonry, built in cement mortar all as specified.

M&L Fly ash Brick work with modular bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and directed.

Description all as per item No 203 here in above but except bricks. Note:Serviceable bricks obtained from Sl item No 202 be reused.

Note for Item No 203 & 204 :- (a) Fly ash bricks shall be burnt clay flyash building bricks as per IS- 13757.

(b) The rates for work curved or polygonal on plan include for all extra cutting and extra waste in the body of the work. It shall be measured as mean length of wall.

(c) Sinking of steining shall be measured separately under relevent item. Well curbs, tie-rods, etc. shall be measured under the appropriate item.

(d) bricks shall be of class designation 75 (Kgf/cm).

(e) The quoted rate shall be deemed to be inclusive for all scaffolding, ladders, plant and templates required

(f) Exposed faces of brick work shall be fair.

(g) Exposed faces shall be facing with best bricks

(h) The quoted rate shall be deemed to be inclusive for Plumb to angles

(j) Forming reveals to jambs where fair cutting on exposed faces shall not be involved

(k) The quoted rate shall be deemed to be inclusive for preparing tops and sides of existing walls and the like for raising and extending

(l) Building in vertical seismic reinforcement at the jambs of openings, corners of walls, etc.shall be grouting in cement mortar 1:4

M&L Grating doom 125mm dia with waste hole of PTMT (minimum weight 40gms) including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed.

M&L PVC (SWR) gully trap 125/110 mm dia of outlet pipe, including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed.

Taking out/pumping contaminated sewage water from Grease trap incl inlet/outlet chamber after plugging incoming sewage line, through suction(vaccum) type machine mounted on LMV/HMV and facility of high pressure vaccum and removing and dumping off the same out side MD land/contonment at the place marked for the purpose by local municipality or the authority controling the area as directed by Engr-in-charge.

M&L Cleaning and Removing silt, grit , mud and other materials from covered drain in foul condition including removing materials from the site to outside MD land including necessary removing cover slabs and replacing after cleaning complete area including making good any damages complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

M&L Joist, channel, angles or tee sections fixed independently, without connection platess Fe-290 Gde E-165 etc all as specified and as directed

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted , bolted or welded attachment.(Fe 410 -W (Gde- E-250) quality -A complete all as specified and as directed.

M&L Stack clamps made out of 50 mm x 3 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and directed.

M&L Applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new or previously untreated steel surfaces of any description exc 10cm width or girth complete all as specified and as directed.

Note for item No 225:- (a) Synthetic enamel paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

M&L Salt-glazed stoneware drain pipes, 200 mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe,of any size including damaged haunching/ bed concrete etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 200 mm bore of pipe, complete all as specified and as directed.

M&L Salt-glazed stoneware drain pipes, 150mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe,of any size including damaged haunching/ bed concrete etc complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 150 mm bore of pipe, complete all as specified and as directed.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S & FSolid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tubecomplete all as specified .

Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

M & L 100 mm long aluminium, anodised, barrel tower bolts of extruded section including taking down existing one complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs jindal or Equivalent aluminium anodised ventilator/window with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and two portion to be provided with 4mm thick plain glass fixed shutter and remaining one portion to be louvered using 4mm thick glass louvered portion incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S&F in repair powder coated aluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 37x19x2mm complete all as specified and as directed.

Taking down carefully any type of steel rolling shutters, of size exc. 5 Sqm but n. exc. 15 Sqm each , inspecting/notifying the defective springs, bearings, shaft, side guides, Gear box, Gear box, etc including greasing and replacement of unserviceable/ defective parts and re fixing in the same and releasing the tension in the springs, lowering complete all as specified and directed by Engineer - in - Charge

S&F 6mm thick frame less bevelled edge mirror fixed with steel stud including taking down existing one complete all as specified and as directed by Engineer-in-Charge.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty including taking down existing wire cloth complete all as specified and directed.

S&F Aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed by Engr-in-charge.

S&F in repair sinks made of stainless steel 1 mm thick with washers,wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets an connecting union to pipe ,overall size 495mmx420 mm and bowl size 410 mm x 330 mm x160 mm complete all as specified and directed.

M&L White seat cover only of Niagara coupled closet with all fittings including taking down existing one Complete all as specified and as directed Cat Part No C8176 fittings series of Niagara of Parryware or equivalent.

M&L in repairs 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed.

Note for item No 252 :- (a) The unit rate shall be include for taking down existing GI pipe and connections and all fittings as directed.

(b) The unit rate shall be include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

M&L 25mm outer dia of pipes PPR gate valves (brass insert) including taking down damaged existing one complete all as specified and directed.

S&F in repair Pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe Cat Part No.QT F2006101, HT F3001101 of CERA or equivalent to /Parryware/Hindware/ Jaguar including taking down existing one complete as directed by Engr-in-charge.

S&F in repair Bib Cock with wall flange screwed down screwed for iron pipe 15mm bore CAT Part No QT F2006151, HT F3001151 of CERA or equivalent to Parryware/Hindware/Jaguar including taking existing one complete as directed by Engr-in-charge.

S&F CP 2 way bib cock with wall flange fancy type screwed down screwed for iron pipe in repairs 15mm bore CAT Part No-Sl. No- QT F2006163 of CERA or equivalent in Parryware ,or as per list of makes Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F CP Hand shower (Health Faucet) with 1.20M braided hose pipe with 8mm bore wall Hook with N.R.V (Back Flow Preventor) CAT Part No-S. No-F8030401AB of CERA equivalent in ESSCO/ Kohler as per list of makes Including taking down existing one complete all as specified and as directed by Engineer-in-Charge

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair Towel rail 24" long for wash basin complete all as specified and as directed. (Make : CAT Part No-F5007103 of CERA series or equivalent make of hindware / parriware

M&L Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, CAT Part No G3007A1 of Parryware or equivalent to Hindware/Cera including taking down existing one complete as directed by Engr-in-charge.

S & F 20 MM bore dia of pipe Ball brass valves. high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule including taking down existing one complete all as manufactures and all as specified and directed by Engineer- In - charge

M&L in repairs for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to IS-15658 of 60mm thickness M-35 grade, laid over and including M sand cushion of 50mm thick and packing the sides with PCC 1:3:6 complete all as specified and directed. Note : The Unit rate quoted is included for Demolition of Stone Slabs and tiles of any description or thickness in floors,aprons etc laid bedded and pointed in any mortar and removing of debris outside of MD land

M&L Low density polyethylene (LDPE) pipes 32 mm bore of pressure rating 6 kgf/sqcm for sink/ wash basin including taking down existing pipe complete all as specified and as directed.

M&L Cutting into existing manholes for connecting new drains, making good pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4 type B-1 using 20mm graded stone aggregate) smooth finished and reforming benching as required 150mm internal bore, complete all as specified and as directed.

supply and fixing in repairs vanitary counter top wash basin (Jaquar - Thin rim table top basin, size 415 x 415 x 145mm round) with MDF cabinet of size 723 x447 x735mm all as specified and as directed.

S& F in repairs Vitreous china wash down water closet pan (pedestal pattern) wall hung of CERA, Compact (snow white) carona seat cover 490 x 350 x 330 mm, hinges, fixing accessories with concealed flush cistern fittings, S trap -300mm complete fixed, all as specified and as directed.

S & F CP pillar cock pressmatic auto closing fancy type 15mm dia CP with capstan head screwed down high pressure screwed for iron pipe CAT Part No-Sl. No-PRS-031 Jaquar Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

M&L preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , treading, oil, greasy spots and applying one coat oil bound distemper complete all as specified and as directed.

M & L preparation of old plastered or unplastered surface of ceiling brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spotsand applying one coat of white wash complete all as specified and directed.

S&F in repairs PVC water storage tank cover suitable for 250/ 300 ltrs capacity tank with locking arrangement complete all as specified and directed

Cleaning of service tanks of 250/ 300 ltrs capacity on roof top of bldgs upto five storrey after disconnection from inlet and outlet pipe, removing of float valve of service tank and keep aside safely for reuse drain out water through drain plug, cleaning thoroughly to remove all scales and dirt by brushing internal surface, cleaning properly inside with soda wash, flushing out with fresh water, re-positioning of tank at same place, re-connecting inlet and outlet pipes, closing of drain plug, re-installation of float valve duly cleaned, writing/ labelling the record of cleaning carried out with white bold letter such as "TANK CLEANED ON"--------- (month and year), including removing creepers, vegitation and roots of plants, trees branches on or surrounding of service tank complete all as directed.

M & L French polishing on old wooden surfaces of any description, width or girth including cleaning and preparing the surface with one or more coats complete all as specified and directed.

M & L repair/ maintenance and making the continuity of supply for rectifying the defects including taking down defective electrical items such as light point, fan/exhaust fan point, call bell point, socket point 5A/15A, switches, sockets, regulator, lamp holder, brackets, bell, buzzer, push button, ceiling rose, pendent, any type of MCB's, SPN DB's any type of internal light fixtures, any type of lamp, ceiling fan, exhuast fan, geyser, capacitor, replacement of fuse wires and all elcectrical accessories in day to day/door to door maintenance including reconnection with S&F small pieces of elctrical cable of size upto 6 sqmm single core and length not exceeding 0.50m complete all as specified and as directed.

Note:- following shall be part of job under item No 276:-

(a) The above job shall be carried out by a trained electrician having ITI in electrical, documentary proof of the education of tradesman shall be produced before commencement of work.

(b) All bldg light complaints including service connection, submain & internal electric for entire Domestic area of AF Stn sulur shall be attended.

(c) Record of complaints/complaint slip showing qtr No, bldgs No, nature of job supported with users signature shall be prepared as per format directed by Engr-in-charge & will be deposited to concerned JE E/M within 24 hrs.

(d) Necessary complaints slip/complaints register & other stationary required shall be contractor responsibility.

(e) All sort of petty T&P items such as PVC insulation table, ladder, galvanised screws, nuts, bolts, washers etc. required to accomplish the job shall be provided by the contractor with out any extra cost to dept.

(f) Defective items if any, required to be replaced shall be measured and paid separately.

(g) The quoted rate is deemed to be inclusive for small pieces of elctrical cable of size upto 10 sqmm single core and length not exceeding 0.50m

(h) The contractor shall maintain a record of all urgent/ routine works and if the work is repeated due to poor workmanship, he will be liable to repair the same without any extra expenditure to the Govt.

(j) In case of any delay in attending the complaint more than 12 hrs after handing over routine/urgent complaints, the contractor shall be liable to pay the penalty as described in penalty clause given here as under.

(k) The penalty shall be applicable to the contractor if the delay is noticed by the Engr-in-Cahrge more than twelve hrs after handing over works of urgent/ routine nature to the contractor. The Engr-in-Charge shall handover the slip containing specification of work to the contractor by lodging the time and signature of contractor be obtained on slip. The contractor shall attend the complaint immediately and shall report to Engr-in-Charge with in 12 hrs. The contractor will keep his tradesmen in stand by for attending any routine / urgent works from the executive. If the nature of job is such that the work cannot be completed within period of 12hrs then the facts shall be brought to the notice of the GE/Engr-in-Charge and the period for the working to the complaint shall be decided by the GE/EIC. If the delay is more then twelve hrs period and the GE is not satisfied with the reason for delay then penalty at the rate of Rs 50/- per job shall be deducted from the dues of the contractor. Please note that this penalty is exclusively other then the condition 56 of IAFW - 2249 and shall be treated as interim condition of the contract and shall be enforce above as and when delay in individual job is noticed and no claim whatsoever on this account shall be entertained by the Deptt.

(l) The decision of the Accepting Officer in this regard shall be final and binding.

Supply & fix starter for 40W flourecent tube light fittngs 1x40 /2x40 watts 230V. Make : Philips/ Bajaj/ CG

Supply & fix single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996 all as specified (Make/Model : Lexic MCB of MDS Legrand Cat No :408587 to 408595 / Siemens/ Schnieder.

Supply & fix electric bell, AC 230 volt, single pole Ding Dong type complete all as specified and directed. Make : Anchor/ cona/ Plaza

Supply & fix 4' 20W/ 18W LED tube rod suitable for existing fitting. Make : Philips, Bajaj, Havells or equivalent approved make.

Supply & fix 2.5 mfd condensor for ceiling fan complete all as specified and directed. Make : Epcos/ Asian/ Tyton

Supply & fix plug top 3 pin 15 amps AC 230 volts complete all as specified and directed. Make : Havells/ Cona/ Plaza

Supply & fix plug top 3 pin 5 amps AC 230 volts complete all as specified and directed. Make : Havells/ Cona/ Plaza

Supply & fix bakelite sheet not less than 3 mm thick of size 100 x 100 mm complete all as specified and as directed. Make : Hylam/ Formica/ Green laminated boards

Supply & fix electronic fan regulator modular typre 230 volts, step type socket type, hum free 100/240 watt Make : Havells / Schnieder/ Crabtree.

Supply & fix bell push. Make : Anchor/ Cona/ Havells

Supply & fix switch piano flush type 5 Amps 240 volts single pole one way. Make : Anchor (Model Penta PC), Havells (Reo), SSK (Topline)

Supply & fix switch piano flush type 5 Amps 240 volts single pole two way. Make : Anchor (Model Penta PC), Havells (Reo), SSK (Topline)

All as per item No 300 here-in-before but 15 Amp Make : Anchor (Model Penta PC), Havells (Reo), SSK (Topline)

Supply & fix shuttered socket outlet 3 pin 5 amps, flush type

Supply & fix shuttered socket outlet 2 in 1, 5 pin, 5 and15 amps

Supply & fix switch socket combination out let 3 pin 5 amps, flush type.

Supply & fix switch socket combination out let 5 in 1, 5 pin 5 and 15 amps, flush type.

Supply & fix for Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked,

Supply & fix lamp holder, insulated body, cord grip pattern SP 230 volt, complete all as specified and as directed.

Supply & fix electronic fan regulator 230 volts, step type socket type, hum free 100/240 watt. Make : Havells / Schnieder/ crabtree

Supply & fix PVC gang box 1 way 05 amp . Make. Cona/SSK/Anchor

Supply & fix switch socket combination outlet 3 in 1/ 3 pin 3 and 5 amps flush type with box

Supply & fix switch socket combination outlet 5 in 1/ 5 pin 5 and 15 amps flush type with box

Supply & fix electronic fan regulator 230 volts, step type, switch type, hum free 100/ 240 watt. Make : Anchor/ Cona/ Havells

Supply & fix in repair PVC casing/ capping batten of 15 mm (width) complete all as specified and directed. Make : Polycab/Modi/ Presto Plast

Supply & fix in repair PVC casing/ capping batten of 20 mm (width) complete all as specified and directed. Make : Polycab/Modi/ Presto Plast

Supply & fix in repair PVC casing/ capping batten of 25 mm (width) complete all as specified and directed. Make : Polycab/Modi/ Presto Plast

Supply & fix electric buzzer, AC 230 volt, single pole complete all as specified and directed. Make : Anchor/ cona/ Plaza

Supply & fix modular switch 1 way 6 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular Socket, 6A - 2/3 pin combined 2 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular switch 1 way 16 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular Socket, 16A - 2/3 pin combined 2 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular white cover plate with frame,3 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular white cover plate with frame,4 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix modular white cover plate with frame,6 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Supply & fix in repair rigid, non-metalic, PVC conduit pipe, ISI marked, 32 mm bore, including bends, saddles, accessories complete all as specified and as directed. Make : Prince/ Supreme/ Diplast

Supply & fix in repair rigid, non-metalic, PVC conduit pipe, ISI marked, 25 mm bore, including bends, saddles, accessories complete all as specified and as directed. Make : Prince/ Supreme/ Diplast

Taking down aluminum/copper point wiring on & including hard wood battens, surface conduit and board/ blocks etc or through conduits for light, socket or power point, fan point complete (Taking down of fittings such as switches, sockets, bells, ceiling rose, holders , regulators, light fittings, MCB, lamps etc shall be measured and paid seperately) and making good the disturbed plaster surfaces of wall, floor, ceiling and painting 2 coat of white wash/distamber to meet the existing surface and removing materials and debris to reinstate the premise neat and clean complete all as specified and directed.

M&L point wiring using approved colour coding as per IS for one light/bell/buzzer point controlled by one switch or one fan point controlled by one switch & fan regulator with PVC insulated, unsheathed FRLS multi stranded copper conductor 1.5 sqmm (nominal area) 1100 volt grade cable for phase & neutral drawn through PVC casing Caping with and including new MS/ cast iron sunken boxes duly painted with two coats of anticorrosive paint over a coat of red oxide primer on surface in touch with wall and synthetic enamel paint over a coat of red oxide on other side, covered with 3mm thick plastic laminated sheet for mounting switches, regulators, sockets etc including 1.5 sqmm (nominal area) copper conductor PVC insulated, unsheathed, multi stranded FRLS cable as earth wire and connected to earth dolly complete all as specified and as directed for the fwg :- Make of Casing Capping : Polycab/ Modi/ Presto Plast Make of Wire : Plaza/ Polycab/ Havells

One light point/fan/bell point controlled by one switch

All as per item No. 327 here in before but for One 3 pin socket out 5 amp on the same board

All as per item No. 327 here in before but for one switch socket outlet 3 pin 5 Amps on independent board

All as per Sl No 327 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently

M&L point wiring using approved colour coding as per IS for one light/bell/buzzer point controlled by one switch or one fan point controlled by one switch & fan regulator with PVC insulated, unsheathed FRLS multi stranded copper conductor 1.5 sqmm (nominal area) 1100 volt grade ISI 694 marked cable for phase & neutral drawn through concealed PVC Conduit, ISI marked with and including new MS/ cast iron sunken boxes duly painted with two coats of anticorrosive paint over a coat of red oxide primer on surface in touch with wall and synthetic enamel paint over a coat of red oxide on other side, covered with 3mm thick plastic laminated sheet for mounting switches, regulators, sockets etc including 1.5 sqmm (nominal area) copper conductor PVC insulated, unsheathed, multi stranded FRLS cable as earth wire and connected to earth dolly complete all as specified and as directed for the fwg :- Make of Conduit : Avon Plast/ Supreme/ Diplast Make of Wire : Plaza/ Polycab/ Havells

One light point/fan/bell point controlled by one switch

All as per item No. 332 here in before but for one 3 pin socket out 5 amp on the same board

All as per item No. 332 here in before but for one switch socket outlet 3 pin 5 Amps on independent board

All as per Sl No 332 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently

M&L taking down of ceiling fan of size 1200/1400mm for safety checking by replacing defective parts/painting/rewinding and re-fixing the ceiling fan after repairs,all as specified and as directed by Engr-in-charge. (Note:- The cost for replacement of unserviceable parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional and making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.5 Sqmm from ceiling rose/ connector fan (minimum 0.50 Mtr length) complete all as specified and directed Note:- Taking down defective parts are deemed to be inclusive in quoted rate

Note for item No 337 :- (a) In each job, checking the functioning of fan including its connections, cleaning of fan, greasing of fan and mechanical check i.e. tightening of loose screw, nuts, bolts, etc are inclusive in unit quoted rate.

(b) The above job shall be carried out by a trained electrician having qualified in ITI ( electrician Trade), documentary proof of the education of tradesman shall be produced, before commencement of work.

(c) The entire job will be carried out in Air Force stn Sulur and necessary documents showing qtr No, bldg No supported with user signature shall be prepared as per format directed by Engr-in-charge and will be deposited to concerned JE (E/M) within 24 hrs.

(d) Maitenance of documents ie complaint slip/complaint register & other stationery required shall be of contractor's responsibility.

(e) Necessary T&P such as ladder, required manpower for taking down and refixing after repair shall be of contractor's responsibility.

(f) All types of T&P, PVC insulation tape, minor nuts, bolts, washers etc required for maintaining the services shall be provided by contractor without any cost to the department.

(g) Any fan found defective/not working shall be brought to AGE E/M store yard & re-fixed after repairing.

(h) In case of major defects, entire job shall be completed within 10 days from the date of registration of complaint, failing which penalty charges @100/- per day shall be recovered.

(j) In case of minor defects, entire job shall be completed within12 hrs from the time of registration of complaint, failing which penalty charges @ 50/- per job shall be recovered.

(k) The contractor shall maintain a record of all urgent/ routine works and if the work is repeated due to poor workmanship, he will be liable to repair the same without any extra expenditure to the Govt.

Supply and fix rotor of ceiling fan of any size complete all as specified and directed.

Supply and fix fan canopies for ceiling fan size of 1200mm/1400mm complete all as specified and directed.

Supply and fix gun metal bush of suitable size for ceiling fan 1200mm /1400 mm sweep complete all as specified and directed.

Supply and fix fan bearing suitable for ceiling fan 1200mm /1400 mm sweep complete all as specified and directed. (bearing with 8 balls shall be used )

Supply and fix down rod for ceiling fan with 15mm dia (of length not less than 45cm and not more than 60cm) with hanging clamps for ceiling fan complete all as specified and directed.

Supply and fix Rubber reel bushes for ceiling fan of size 1200/1400mm complete all as specified and directed.

Supply and fix 'U' clamp for hanging ceiling fan with all nuts, bolts and washers complete all as specified and directed..

Supply and fix outer body of ceiling fan of any size complete all as specified and directed.

Supply and fix blades (made of aluminum) suitable for 1400mm sweep ceiling fan of any make with set of screws complete all as specified and directed.

Supply and fix safety pins 40mm to 50mm long with nuts and bolt with washers for ceiling fan of size 1200/1400mm complete all as specified and directed.

Supply and fix blades (made of aluminum) suitable for 1200mm sweep ceiling fan of any make with set of screws complete all as specified and directed .

Supply and fix down rod for ceiling fan with 15mm dia (of length not less than 90cm and not more than 120cm) with hanging clamps for ceiling fan complete all as specified and directed.

Supply and fix down rod for ceiling fan with 15mm dia (of length not less than 180cm and not more than 210cm) with hanging clamps for ceiling fan complete all as specified and directed.

Material and labour for winding of ceiling fan motor 1200 mm sweep of any make with super enameled copper winding wire of existing gauge (wt of copper winding wire per fan 350 to 500 gms) including cutting and getting out old burnt winding, sleeve work, varnishing with E class insulation varnish, threading, connections with twin core copper flexible wire of size 0.0076mm of length not more than one meter with each fan complete all as specified and directed. Note :- Motor shall be wound with machine inside MES complex only.

Description all as per Sl item No 361 here in above but ceiling fan of 1400 mm sweep

Taking down of exhuast fan any size/capacity after disconnecting cable connection, and refixing same in original position after necessary repair/over hauling including replacement of parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional and making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.5 Sqmm from ceiling rose/ connector fan (minimum 0.50 Mtr length) complete all as specified and directed Note:- Taking down defective parts are deemed to be inclusive in quoted rate

Note for item No 363 :- (a) In each job, checking the functioning of fan including its connections, cleaning of fan, greasing of fan and mechanical check i.e. tightening of loose screw, nuts, bolts, etc are inclusive in unit quoted rate.

(b) The above job shall be carried out by a trained electrician having qualified in ITI ( electrician Trade), documentary proof of the education of tradesman shall be produced, before commencement of work.

(c) The entire job will be carried out in Air Force stn Sulur and necessary documents showing qtr No, bldg No supported with user signature shall be prepared as per format directed by Engr-in-charge and will be deposited to concerned JE (E/M) within 24 hrs.

(d) Maitenance of documents ie complaint slip/complaint register & other stationery required shall be of contractor's responsibility.

(e) Necessary T&P such as ladder, required manpower for taking down and refixing after repair shall be of contractor's responsibility.

(f) All types of T&P, PVC insulation tape, minor nuts, bolts, washers etc required for maintaining the services shall be provided by contractor without any cost to the department.

(g) Any fan found defective/not working shall be brought to AGE E/M store yard & re-fixed after repairing.

(h) In case of major defects, entire job shall be completed within 10 days from the date of registration of complaint, failing which penalty charges @100/- per day shall be recovered.

(j) In case of minor defects, entire job shall be completed within12 hrs from the time of registration of complaint, failing which penalty charges @ 50/- per job shall be recovered.

(k) The contractor shall maintain a record of all urgent/ routine works and if the work is repeated due to poor workmanship, he will be liable to repair the same without any extra expenditure to the Govt.

Material and labour for winding of Exhuast fan 450 mm sweep of any make with super enameled copper winding wire of existing gauge (wt of copper winding wire per fan 250 to 500 gms) including cutting and getting out old burnt winding, sleeve work, varnishing with E class insulation varnish, threading, connections with twin core copper flexible wire of size 0.0076mm of length not more than one meter with each fan complete all as specified and directed. Note :- Motor shall be wound with machine inside MES complex only.

Description all as per Sl item No 374 here in above but 300 mm sweep

Description all as per Sl item No 374 here in above but 250/230/200 mm sweep

Supply and fix fan bush of suitable size for exhaust fan of the any sweep complete all as specified and directed.

Supply and fix metal louvers of suitable size for exhaust fan of the 450mm sweep complete all as specified and directed.

Supply and fix fan bearing of suitable size for exhaust fan of 450mm sweep including greasing complete all as specified and directed..

Supply and fix metal louvers of suitable size for exhaust fan of the 300mm sweep complete all as specified and directed.

Supply and fix fan bearing of suitable size for exhaust fan of 300mm sweep including greasing complete all as specified and directed.

Supply and fix metal louvers of suitable size for exhaust fan of the 250/230/200mm sweep complete all as specified and directed.

Supply and fix fan bearing of suitable size for exhaust fan of 250/230/200mm sweep including greasing complete all as specified and directed.

Inspection,checking alignment and minor repairs of storage water heater 25/35/50 ltr capacity of any type any make vertical/ horizontal type which includes the following complete all as specified and directed:- (a) Inspection, taking down the defective parts, taking out of drain plug & dewatering and refix the same complete all as directed . (b) Checking water tightness of storage tank . (c) Checking stop cocks with outlet/inlet pipe of geysers, pressure reducing valves etc to ensure free movement of water and easy functioning of parts. (d) Inspecting over flow vent pipe connections to ensure water-tightness and proper flow. (e) Checking and correct earth continuity of electrical items. (f) Checking functioning of heating element and correct setting adjustment of thermostat upto 55º C. (g) Alignment of reducing valves, checking of dead weight type high pressure release valve and visual check of fusible plug for its intactness. (h) Replacement of defective spares shall be measured and paid under relevant items mentioned below separately as supply and fix.

Note for item No 384 :-

The above job shall be carried out by a trained electrician having ITI in electrical, documentary proof of the education of tradesman shall be produced, before commencement of work.

The entire job will be carried out in entire Tech area of Air Force stn Sulur and necessary documents showing qtr No, bldg No supported with user signature shall be prepared as per format given by Engr-in-charge and will be deposited to concerned JE (E/M) within 24 hrs.

All types of T&P, PVC insulation tape, minor nuts, bolts, washers etc required for maintaining the services shall be provided by contractor without any cost to the department.

S&F Heating element, thread type, 1.5 KW 230 volts, ISI marked suitable for 25/50 ltrs geysers of any capacity and any make including washer/packing suitably complete all as specified and as directed. Make:- Theeta/Swarna or equivalent approved make.

Supply and fix pressure relieving valve CP brass confirming to relevant IS with washer suitable for 15mm bore GI pipe suitable for 25/50 ltrs geysers complete all as specified and as directed. Make : Leader / Theta or equivalent approved make.

Supply and fix thermostat switch range of 30-80 degree suitable for geysers of 25/50 ltrs capacity (ISI marked) complete all as specified and as directed. Make : Havells/Theeta/Swarna/ Elcon or equivalent approved make.

S&F Glass wool for insulation of Geysers any capacity and any make complete all as directed by the Engr-in-Charge.

S&F Heating element, tikona type, 1.5 KW 230 volts, ISI marked suitable for 25/50 ltrs geysers of any capacity and any make including taking down old one including washer/packing suitably complete all as specified and as directed. Make :Theeta/Swarna or equivalent approved make.

S&F PVC connection for hot/ cold water made of double layer nylon braided and fabric at a pressure of 6kg/sq cm at both ends, 450 mm long, heavy duty with CP brass adopters, washers, suitable for 15 mm bore pipe complete all as specified and as directed.

S&F Indicator lamp for geyser 25/50 ltr capacity of colour green & red complete all as specified and as directed. Make : Usha / Bajaj/ Crompton or equivalent approved make.

S&F Copper inner tank of minimum 20 gauge sheet rated pressure not less than 7kg/sqcm suitable for 25 ltrs capacity geysers (wt not less than 3.75 kg) as per sample complete all as specified and as directed.

Supply and fix brass non return valves, screwed down, high pressure, screwed both ends for 15mm bore iron pipe or for union, ISI marked, complete all as specified and as directed. Make : Seiko, Leader, Zoloto or equivalent approved make.

M & L Cutting and screwing existing steel water tubing 15/20/25 mm bore for addition /alteration required for connections to geysers etc complete all as specified and directed.

Supply and fix bottom cover of MS sheet 20 gauge suitable for 25 ltrs capacity geysers and providing a coat of red oxide primer to inner surface and applying one coat of synthetic enamel paint by spray painting to outer surface complete all as specified and as directed.

S&F provision brazing of inner copper tank Geysers using quality of copper electrode blow lamp welding process brazing length n.exc 10 cm all as specified and directed at site the Engr-in-Charge.

Supply and heating element, cup (square) type, 1.5 KW 230 volts, ISI marked suitable for 25/50 ltrs geysers of any capacity and any make including taking down old one including washer/packing suitable complete all as specified and as directed. Make : Theeta/Swarna or equivalent approved make.

Supply and fix PVC connection for hot/ cold water made of double layer nylon braided and fabric at a pressure of 6kg/sq cm at both ends, 600 mm long, heavy duty with CP brass adopters, washers, suitable for 15 mm bore pipe complete all as specified and as directed.

Taking down carefully storage water heater (geyser) 25 ltr capacity of any type, any make from the location by removing the electric & water supply connection and shifted to work shop/MES store yard for repair and re-installation at any location including S&F in repair of heavy duty pin type fastener 4" long and making necessary inlet/outlet electric & water supply connection from existing source to geyser complete all as specified and as directed.

Description all as per Sl item No. 403 here-in-above but 35/50 Ltr capacity.

S&F Heating element, tikona type, 2.00 KW 230 volts, ISI marked suitable for 25/50 ltrs geysers of any capacity and any make including provision of suitable washer/packing complete all as specified and as directed. Make : Theeta/Swarna or equivalent approved make.

M&L for painting of outer surface of 25 ltrs storage type water geysers after cleaning of dust & other organic/inorganic materials if any and applying one coat of synthetic enamel white paint by spray painting and writing MES No on the geyser complete all as specified and as directed.

Supply and fix indoor assembly, compatible to existing geyser, 25 Ltr capacity in any make, with inlet and thermostat pipe with drain plug inclusive of clamps for holding the element with nuts, bolts and gasket complete all as specified and as directed.

S&F Copper inner tank of minimum 20 gauge sheet rated pressure not less than 7 Kg/sqcm suitable for 35/50 ltrs capacity geysers (wt not less than 5.25 kg) as per sample complete all as specified and as directed.

Supply and fix bottom cover of MS sheet 20 gauge suitable for 35/50 ltrs capacity geysers and providing a coat of red oxide primer to inner surface and applying one coat of synthetic enamel paint by spray painting to outer surface complete all as specified and as directed.

S & F Bottom cover in two pieces for covering the base plate, heating element, thermostat made out of MS sheet 22 gauge as per existing size and shape duly painted with two coat of white synthetic enamel paint over one coat of red oxide primer including preparation of surfaces complete all as specified and as directed.

S&F Heating element, thread type, 2.00 KW 230 volts, ISI marked suitable for 25/50 ltrs geysers of any capacity and any make including taking down old one inlcuding washer/packing suitable complete all as specified and as directed. Make : Theeta/Swarna or equivalent approved make.

Supply and fix 35/50 Ltr capacity in any make indoor assembly, compatible to existing geyser, with inlet and thermostat pipe with drain plug inclusive of clamps for holding the element with nuts, bolts and gasket complete all as specified and as directed.

Neptune Engineers and Builders

pk janardhanan

eurekaenterprises

p.chinnasamy

KSR AND COMPANY

T C KARUNANITHI

kaarthic builders

Lucky Enterprises