EDCH-124/2023-24

Amount

Supply of Following Matarial as per relevent ISS

Danger Board With Clamp

Stone pad

Tee Off Channal

Top Channal

Nut Bolt With Washer

Holding Clamp for Top & Dropper, TPMO etc

Gaurding angle

Dropper Channal

MS Angle Iron 65*65*6 mm, 2700 mm long brassing with clamp

11 KV Fuse Set

Dead End clamp

Copper L- Piece 50*225*10 mm

T/F Base angle

HDPE Pipe Undergrouding Minimum 3 Mtr 160 mm OD PN-4PE-80 Grade U.V Stablized HDPE Pipe as IS:4984 in 6 Metre

Ms Channel 125*65*1300

Lt Incoming Pannel with Metering Qubical

Barbed Wire

Suspension clamp with I hook complete

All Lug 400 sqmm

Lt Piller Box

Pearcing connector

Scope of work

Safe Carriage of following material from Electricty store center Hts to Pit site of work through the Kacha and Pakka road including loading and unloading at the respective ends including the cost of arrangement of labour, T&P, etc. which required for proper completion of work.(Distance 00-50 Kms.)

9/11/13 Mtr Long STP Poles.

11 KV X-Arms, weasal conductor, G.I wire,Disc Insulators, Pin insulators, clamps Abc Bunch and other required line material, if any.

XLPE Cable (3*120 sqmm)

XLPE Cable (3*185 sqmm)

Incoming VCB 600/300/5 AMP 350 MVA

Outgoing VCB 200/100/5 AMP 350 MVA

Safe Carriage of following from Electricty Store center Hathras to Pit Site of Work through the Kacha and Pakka road loading and unloading at the respective ends including the cost of arrangement of labour, T&P, etc. which required for proper completion of work.(Distance 00-70 Kms.)

25/63/100 KVA T/F

Errection of following Poles with grouting including Cutting of kharanja/mettalic road/concrete portion while digging pit & complete H.T./L.T. fittings as per RESPO manual and as per direction of Engineer Incharge including the cost of labour, T&P and carrier etc. required for proper completion of work.

9/11/13 Mtr long STP Pole

Double pole complet fitting

Fixing/ Errection of LT Incoming Pannel with Metering Equiptment, Grouting as per respoo manual all cost of labor, material and T&P which required for completion of work

Fixing/ Errection of 11 KV Switch Gears/VCB, Grouting as per respoo manual all cost of labor, material and T&P which required for completion of work

Errection and grouting of stays as per RESPO Norms and as per direction of supervising engineer. Grouting material i.e. cement, sand, brick ballast/stone ballast etc. shall be arranged by the contractor at his own cost.

Fixing of earthing rod as per RESPO Norms and as per direction of supervising engineer.

Laying, sagging and stringing and jumpering / binding etc. of new & old ACSR Weasal conductor / GI in 11 KV / LT lines as per RESPO manual and as per direction of supervising engineer.

ACSR Dog Conductor

XLPE Cable 3*185 sqmm

XLPE Cable (3*120 sqmm)

Safe Dismenteling of old and used following T/F from Double Pole with opening of all HT/LT Jumpers, all works which required for dismentling of T/F and carriage it up to Store Hathras/ J.E Store all cost of labour and T&P which required for completion of work

25/63/100 KVA T/F

250/400 KVA T/F

Safe Dismenteling of old and used 11 KV Switch Gears/VCB, all works which required for dismentling of T/F and carriage it up to Store Hathras/ J.E Store all cost of labour and T&P which required for completion of work

Resagging of Existing line by stringing and jumpering / binding etc. of new & old ACSR Weasal conductor / GI in 11 KV / LT lines as per RESPO manual and as per direction of supervising engineer.

ACSR Weasal conductor

ACSR Rabit /Dog Conductor

AB Cable 50/95/120 sqmm

Installation of 250/400 KVA T/F on newly/Old constructed Plinth in proper alignment direction & making HT/LT connection all Cost of labour and T&P which required for completion of work

Installation of following T/F on newly constructed double pole in proper alignment direction & making HT/LT connection.

25/63/100 KVA T/F

Fixing of Following Accessirious

11 KV TPMO

11 Kv Fuse Set

Danger Board/Plate

Cable Joiting Kit I/D and O/D

Construction of plinth of size 5' * 5 * 4' above ground level one ft below the ground level of 9" After Exavation of 4 "earth brick ballast shall be provided and rammering will be done properly After ballast shall be provided and rammering will be done properly After that a retaining wall 9"width by fist class brick in ratio 1:4 of cement & sand shall be made . The earth shall be filled up to one ft.below the top of the plinth After this brick ballast shall be provided upto 6"from the earth level and proper rammering shall be done one No. jall of 12 mm MS tor shall be fixed in the hollow of plinth and one ft. thick RCC in ratio of cement sand & stone ballast shall be laid on the top of the plinth. The 12 mm thick plastering shall be done all round the plinth in 1:4 ratio of cement and sand.

Pipe earthing of 250/400 KVA medium Power Transformers

Net Fencing Shall be 1150*1200 mm made of 35*35 mm MS Angle covered by expended netal 14 SWG up to full Height 1200 mm duly steftened by MS flat by an 8 SWG dia bolt & nut

Re Guarding / Guarding of 11 KV line by laying, stringing, sagging and binding of 2 Nos. parallel GI wire 6 SWG after providing, fabrication and fixing of guarding angle and fabrication and fixing of X-guards (Tillis) of GI wire at distance of 3 Mtr.

Drill machine Hole in Road with fixing of 90 mtr HDPE Pipe all cost of Labour and T&P with permission of authority which required for completion of work

Installation of extra ''T'' on the erected poles wherever required alongwith all fitting as per direction of supervising engineer including the cost of labour, T&P etc, required for proper completion of work. The "T" pole shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of material.

Back Cartage of Following Matarial

Acsr weasal Conductor scrap

XLPE Cable

Iron Scrap

Bobby Electricals

VINAYAK ELECTRICALS

R.N. ELECTRICAL WORKS