DEMOLITION AND RE- CONSTRUCTION OF 16 X TOILET CUM BATHROOM BLOCK WITH ALLIED FACILITIES FOR OTHER RANKS UNDER GE (S) BATHINDA AT BATHINDA MIL STN

Amount

Dismantling of old asbestos cement, corrugated or semi-corrugated sheets in roof covering complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description complete all as specified and as directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engineer-in-charge.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) not exceeding 1.5 Sqm each and removal from site complete all as specified and as directed by Engineer-in-charge.

Taking down or up 15 mm bore galvanised iron tubing and removal from site complete all as specified and as directed by Engineer-in-charge.

Taking down or up 20 mm bore galvanised iron tubing and removal from site complete all as specified and as directed by Engineer-in-charge.

Dismantling PVC water storage tank of capacity 250 litres to 500 Liters complete all as specified and as directed by Engineer-in- charge.

Taking down old 15 mm bore chromium plated bib tap complete all as specified and as directed by Engineer-in- charge.

Taking down old 10 liters capacity PVC valve less symphonic action type complete all as specified and as directed by Engineer-in- charge.

Taking down old wash hand basin complete all as specified and as directed by Engineer-in- charge.

Taking down old half stall urinal complete all as specified and as directed by Engineer-in- charge.

Taking down old chromium plated stop valves of 15 to 20mm bore complete all as specified and as directed by Engineer-in- charge.

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thickness below or above ground level of any description and in any position complete all as specified and as directed by Engineer-in-Charge

Demolition of cement concrete reinforced of any discription and in any position, including (reinforcement cut as required to facilitate demolition ) complete all as specified and as directed by Engineer-in-charge

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr deep for pipes / foundation etc or for shafts, wells, cesspits, manholes, pier holes for laying cables etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr depth and getting out in soft/loose soil etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

Material and Labour Brick work with sub class ‘B’ Fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in- charge.

Material and labour Brickwork with sub class 'B' old size Fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia including making of rungs, handles etc complete all as specified and as directed by Engineer-in-charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

All as per item No 19 here in before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders etc. complete all as specified and as directed by Engineer-in-charge.

Material and labour for Reinforced cement concrete, M-25 (Design Mix) using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete including proper compaction by using mechanical viberator complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Reinforced cement concrete, M-25 (Design Mix) using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including proper compaction by using mechanical viberator complete all as specified and directed.

Material and Labour for Reinforced cement concrete, M-25 (Design Mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete including proper compaction by using mechanical viberator all as specified and directed by the Engineer-in-Charge.

Material and Labour for Reinforced cement concrete, M-25 (Design Mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts , including proper compaction by using mechanical vibrator, complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Reinforced cement concrete, M-25 (Design Mix) using 20 mm graded stone aggregate as in Chajjas complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for formwork to soffits of suspended slabs, such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) on flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. on flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter on flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions in Square, rectangular , or polygonal on flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Formwork to chullah hoods, chajjas, troughs and similar items including edges on flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including backing coat of 10 mm in cement mortar 1:4 complete all as specified and directed by the Engineer-in-Charge.

Material and labour for 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces of wall and finishing even & smooth but without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and Labour 15 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces on walls , finishing fair and even , mixed with Liquid Water proof compound as per manufacturer's instructions, complete all as specified and directed by the Engineer-in-Charge. ( Liquid Water proof compound shall be measured and paid separately as supply only under respective item of Schedule 'A' BoQ)

Supply only liquid water proofing compound of approved make complete all as specified and directed by the Engineer-in-Charge.

Material and Labour 5 mm thick rendering in cement mortar 1:3 on thick on concrete surfaces of ceilings surface ,finished even and smooth with out using extra cement complete all as specified and directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered surafaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a alkali resistant priming coat complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.complete all as specified and directed by the Engineer-in-Charge.

Material & Labour Preparation of newly plastered or unplastered surfaces on ceiling and applying three coats of white washing, complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for 75 mm thick PCC 1:4:8 type D-2, using 40mm graded stone aggregate as in sub base complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for 25 mm thick PCC 1:2:4 type B-0, using 12.5mm graded stone aggregate as in floor. complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for 15 mm thick Screed bed r in cement mortar 1:4 complete all as specified and directed by the Engineer-in-Charge.

Material and Labour glazed ceramic tiles of 450mm x 300m x 7 mm thick as in vertical surfaces such as in skirting / dado/ risers of steps etc. set and jointed in neat cement slurry @ 3.00 kg per Sqm and pointed in white or colour of tiles laid over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc . set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match, in floors etc. complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for 75 mm thick PCC 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection, complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micorn) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., minimum thickness of powder coating 50 micron complete all as specified and directed . Note :- Weight of aluminium section/aluminium channel shall be physically ascertained through a board of officers convened by Accepting officer and payment shall be made only after ascertaining the actual weight of aluminium at site.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 4.8 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Supply and fixing factory made PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified in Preamble 8B. 3.1 of SSR Part -II (2020) and all as shown on drawing of SSR Part-II (2020) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Factory made Solid PVC Moulded Door Shutter as in bathroom, toilet, (With BWP particle board) 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC sheet on the front face & 2mm Plain colour PVC sheet on back face, as per specification & drawing

Supply and fixing Butt hinges 100mm , extruded aluminium alloy type B-21 complete all as each specified and as directed by the Engineer-in-Charge.

Supply and fixing Aluminium handles, 150mm long , cast type anodised complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing Aluminium anodised barrel tower bolts of extruded section , 150 mm long complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing Vitreous china under counter wash hand basin, white, flat back, fancy type, size 550 x 400 mm including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of waste fitting and union complete all as specified and as directed by Engineer-in-charge

Supply and fixing 15mm bore pillar tap, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by Engineer-in-charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' trap including connection to drain ( or outgoing pipe) and to flushing pipe, anti syphonage pipe etc., including plastic water closet seat cover black pedestal pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm x 260 mm, white, with integral foot rests with 'P' or 'S' trap including provision of cement concrete bedding ( excluding flushing cistern and flush pipe) including making connections and demolition of concrete/ lime concrete bedding complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets including 32 mm dia flush pipe of polyethylene of low or high density of PVC complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing vitreous china white urinal, bowl type , size 465mm x 355mm x 265mm (minimum), with and including waste pipe white, with and including grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal with wall in cement mortar 1:2 , securing urinal to plugs with and including 60mm long brass screws or brackets, pointing around urinal back in cement etc complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Rotational moulded polyethylene water storage tank three layer 1000 litres capacity including providing 20 mm dia ball brass valve, high pressure with polythene float and fly nut complete, screwed for iron pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 125mm size brass chromium plated shower rose with angular arm with swivel jiont complete all as specified and as directed by Engineer-in- charge.

Supply and fixing PVC connection 15mm dia and 60cm long with Nos. of brass check nuts and washers complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Brass chromium plated Tubular towel rail, 20mm dia , D type, 60 cm long between flanges complete all as specified and as directed by Engineer-in- charge.

Supply and fixing bib tap cast copper alloy, chromium plated, with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and as directed by Engineer-in- charge.. Note :- The minimum weight shall be as given in SSR or in relevant IS

Supply and fixing Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engineer-in- charge..

Material and Labour for Cutting chases in brick wall , pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-in- charge..

Supply and Fixing GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 15 mm complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 20 mm complete all as specified and as directed by Engineer-in- charge.

Supply and fixing stop valve, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing chromium plated with long shank and cup ( concealed type) stop valve for 15 mm bore dia of pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relivent IS.

Supply and fixing Cast iron sand soil waste and vent pipe 100mm bore with or without ears fixed with cement joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

Supply and fixing cast iron spun soil waste and vent pipe 100mm bore with or without ears fixed with cement joints laid in trenches/floors complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 100mm bore cast iron Bends (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Cast iron sand soil waste and vent pipe 75mm bore with or without ears fixed with cement joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

Supply and fixing cast iron spun soil waste and vent pipe 75mm bore with or without ears fixed with cement joints laid in trenches/floors complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 75mm bore cast iron Bends (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Cast iron sand soil waste and vent pipe 50mm bore with or without ears fixed with cement joints fixed to walls complete all as specified and as directed by Engineer-in-charge.

Supply and fixing cast iron 50mm bore cowl complete all as specified and as directed by Engineer-in-charge.

Material and Labour Salt-glazed stoneware gully trap, (Size of gully traps in 150mm x 150mm) square or round mouthed, type 'P complete all as specified and as directed by Engineer-in-charge.

Supply and fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Material and Labour for precast cement concrete concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slabs (for man holes etc) set in CM 1:6 including all necessary from work.

Material and Labour for Extra for forming fair finished drain or channel not exceeding 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed by Engineer-in-charge.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (soil) not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5mtr above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC (1:4:8) type D-2 using 40 mm graded stone aggregates as in concrete bed of (SGSW/RCC) drain pipes of 150 mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in-charge. Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be outer diameter of drain pipes (not of sockets / collar) plus 30cm.

Supply and laying DWCPE (SN 8) drain pipes 150 mm nominal dia as per IS-16098 (Part-II), laid in trenches on bed including all accessories/ fittings/ jointed ring, jointing and testing complete all as specified and as directed by Engineer-in- charge. Note:- Excavation , earth work, bedding and pedestal / anchorage if required shall be measured and paid separately under appropriate item of BOQ/ Sch 'A'

Material and Labour for Septic tank, Excavation ,Returning filling and removal in soft / loose soil , Cement concrete (M-20) using 20mm graded stone aggregate , Brick work with old size burnt clay bricks in CM 1:4, internal plaster 15 mm thick in cement mortar 1:4 mixed with an approved water proofing compound as per manufacturer’s instructions, RCC work M-30 Design Mix in Salb , including RCC precast manhole cover having 6mm plate embedded all around with angle iron frame ,Vent shaft and sludge chambers , sump , RCC Baffle wall in RCC work M-30 Design Mix etc. for 50 users complete all as specified and shown on drawing no. BTD - 16 sheet 1R/3 & 3/3.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Hardcore of gauge n exc. 63 mm of Broken stone or boulders , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfacecomplete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Sand filling under interlocking tiles including consolidation complete all as specified and as directed by the Engineer-in-Charge.Note: Sand shall be approved by GE before incorporation in the work.

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade colour and pattern as approved by GE with grey cement and pigment complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Providing precast cement concrete 1:2:4 Type B-1 using 20mm graded aggregates in Kerb stone,quoin blocks , apex stones set in cement mortar 1:4 , weathering slightly rounded or chamfered angles and throating inlcuding necessary form work complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing SFRC (Steel fibre Reinforcement concrete cover & frame) HD-20, rectangular type , internal size of frame 560mm x 590mm and external size of frame 800mm x 800mm x 100mm including manhole cover having size 590mm x 590mm x 50mm thick set in cement mortar 1:4complete all as specified and as directed by Engineer-in- charge.

Material and Labour for Preparation of roof/ wall concrete / plastered surfaces & applied a coat of cold bituminous primer over cleaned surface @ 0.40 Kg/ Sqm followed by APP modified five layer polymeric membrane 3mm thick, minimum weight 3.50 Kg/Sqm reinforced with polyester non-woven fabric ( weighing not less than 150 gms/ Sqm) , laid as per the manufacturers instruction with side over lap of 75 mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required complete all as specified and as directed by Engineer-in- charge

Material and Labour for 15 mm thick rendering / screed in cement mortar (1:4) on fair faces of brick work or concrete surfaces on roof top surfaces , Parapet, vertical surfaces finishing even and smooth without using extra cement , mixed with Liquid Water proof compound as per manufacturer's instructions, complete all as specified and directed by the Engineer-in-Charge. Note:-1. Liquid Water proof compound shall be measured and paid separately as supply only under respective item of Schedule 'A' BoQ 2. Only Coarse sand (Toka sand) shall be used in rendering / screed as approved by GE.

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc except concealed conduit and sunken boxes and removing the retrieved materials from site complete all as specified and as directed by Engineer-in- charge

Material and labour for concealed Point wiring for one light point / fan point / bell point controlled by one switch (using red, black and green etc colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box (Min 60mm deep and 1.6mm thick sheet, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed by Engineer-in- charge. (switches/ socket / regulator shall be measured and paid separately under appropriate item of BOQ/Sch 'A').

All as per above Srl item No. 100 but for one socket out let 5 Amps point controlled by one switch (on same board) complete all as specified and as directed by Engineer-in-charge. (switches, sockets etc. shall be measured and paid separately under appropriate item of BOQ/Sch A).

Material and labour for concealed Point wiring for one socket out let 15/16 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 2.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box (Min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 2.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed by Engineer-in- charge. (switch, socket shall be measured and paid separately under appropriate item of BOQ).

Supply and fixing switch piano flush type (ISI marked), 5/6Amps, single pole, One way, fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. Note :- Cost of laminated sheet cover for mounting of switch is included under respective item of BOQ (point wiring)

Supply and fixing switch piano flush type (ISI marked), 15/16Amps, single pole, One way, fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. Note :- Cost of laminated sheet cover for mounting of switch is included under respective item of BOQ (point wiring)

Supply and fixing Socket outlet multipurpose type, 2 in 1, 3 pin, 5/6 Amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in- charge. Note :- Cost of laminated sheet cover for mounting of switch is included under respective item of BOQ (point wiring)

Supply and fixing Socket outlet multipurpose type, 2 in 1, 6 amp and 16 amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in- charge. Note :- Cost of laminated sheet cover for mounting of switch is included under respective item of BOQ (point wiring)

Supply and fixing Ceiling Rose, polycarbonate, isolated body, surface bakelite 3 terminal, 240 volts, 5/6 Amp complete all as specified and as directed by Engineer-in- charge.

Material and Labour Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in- charge

Supply and Fixing LED 9W Lamp base B-22 complete all as specified and as directed by Engineer-in- charge

Supply and fixing (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 200 Amp rated bus bar) SPN, 8 Way 240V, suitable for mounting MCB/Isolator etc, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-43 protection class, and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB/Isolator etc shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing MCB ‘B’ curve suitable for 230 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB complete all as specified and as directed by Engineer-in-charge

Supply and fixing MCB ‘C’ curve suitable for 230 volts AC supply, 32 Amps, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB complete all as specified and as directed by Engineer-in-charge

Supply and fixing single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting 1x10 Watt, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and directed by Engineer-in-Charge..Note:The rate of three core flexible copper conductor cable of suitable size from ceiling rose to fitting is included in this item and nothing shall be paid extra on this account.

Supply , fixing and testing LED light fitting 1 x 9/10 Watt bulkhead luminaire including LED holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and directed by Engineer-in-Charge..Note:The rate of three core flexible copper conductor cable of suitable size from ceiling rose to fitting is included in this item and nothing shall be paid extra on this account.

Supply , fixing and testing 35 watt LED Security light fitting with and including LED bulbs , with pressure dei-cast housing along with prismatic polycarbonate modular secondary lens optics for City Road application with IP66 ingress protection and impact resistance of IK08. 4kV inbuilt surge protection with top opening driver cover for easy maintenance with complete accessories and with and including GI bracket made out of of light grade GI pipe 40 mm dia upto 1.2 mtr length cut to length, bent to shape with 02 sets of MS clamps made out of 25mm x 3 mm MS flat iron with suitable bolt and nuts and testing complete all as specified and as diected by Engineer-in-charge.

Material and Labour for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6.3 mm size burried directly in ground to depth not less than 2.25m below normal ground level with top edge of the plat not less than 1.5 mtr below normal ground level surrounded with char coal and common salt filling in alternate layers of 15cm thick and connected to galvanised earth wire 4.0 mm dia by means of bolts, nuts, check nuts and washers etc made out of GI iron including 15mm dia GI pipe light grade for protection of earth to distribution board 20 mm dia GI pipe medium grade connected to funnel heavy wire mesh as watering pipe including necessary excavation and earth work PCC 1:2:4 type B-1 for concrete pit 10 mm thick PCC slab cover frame all as specified and shown in electric plate Nos 3/SSR Part-I and testing on completion complete.

Supply and fixing Heavy duty metal body exahust fan of 450mm sweep, 240 volt, energy efficient complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cement mortar white washing to match with existing colour complete all as specified and as diected by Engineer-in-charge.

Supply and fixing Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and as diected by Engineer-in-charge.

Supply and fixing PVC insulated aluminium conductor heavy duly served with inner sheathing of PVC tape and overall PVC sheathed cable of size 16 sqmm 2 core, 1100 volts grade conforming to IS-1554 Part-I complete all as specified and as diected by Engineer-in-charge.

Note:- (i) The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ.

Ajay Enterprises

LM CONSTRUCTIONS

JAGMEET SINGH CONTRACTOR

M/s Verma Construction Company

SHARDA ENTERPRIES

M/s MITTAL CONSTRUCTIONS