CONSTRUCTION OF NON-EXPLOSIVE STORAGE PLINTH WITH ROOF(Qty-04) AT AF STATION AGRA

Amount

SCHEDULE A PART I (BUILDING WORKS)

Lump sum price worked out by the contractor for Construction of NON-EXPLOSIVE STORAGE ACCN AND STORAGE CUM ANNEXE WITH ROOF(Including RAMP as shown on drawing ) as SHOWN IN DRAWINGS AND listed in Sch ‘A’ Part I.

SCHEDULE A PART II (FIRE POINT)

Lump sum price worked out by the contractor for FIRE POINT as listed in Sch ‘A’ Part II.

SCHEDULE A PART III (PCC ROAD & HARDSTANDING)

Lump sum price worked out by the contractor for PCC ROAD & HARDSTANDING as listed in Sch ‘A’ Part III.

SCHEDULE A PART IV (FENCING & GATE)

Lump sum price worked out by the contractor for FENCING & GATE FOR STN ARMOURY ONLY as listed in Sch ‘A’ Part IV.

SCHEDULE A PART V (INTERNAL ELECTRIFICATION)

Lump sum price worked out by the contractor for INTERNAL ELECTRIFICATION as listed in Sch ‘A’ Part V.

SCHEDULE A PART VI (AIR CONDITIONING)

Lump sum price worked out by the contractor for AIR CONDITIONING as listed in Sch ‘A’ Part VI.

SCHEDULE A PART VII (EXTERNAL WATER SUPPLY)

Lump sum price worked out by the contractor for EXTERNAL WATER SUPPLY as listed in Sch ‘A’ Part VII.

SCHEDULE A PART VIII (EXTERNAL ELECTRIC SUPPLY)

Lump sum price worked out by the contractor for EXTERNAL ELECTRIC SUPPLY as listed in Sch ‘A’ Part VIII.

SCHEDULE A PART IX (SITE CLEARANCE ,EARTHWORK & EXCAVATION )

Lump sum price worked out by the contractor for SITE CLEARANCE , EARTHWORK & EXCAVATION as listed in Sch ‘A’ Part IX.

Schedule A Part -X (Miscellaneous Items of B&R and E&M (to be quoted by the tenderer in BOQ)

M&L for Forming 25 mm wide expension joint fill with compresibble synthetic filler board for complete depth as per site requirement,provision of closed cell polyethylene backup sheet 12 mm thick fillled with polyurethane sealent (Min depth of sealent above polyethylene sheet shall be of 15 mm) complying with BS 5212,BS4254,and EN 41875-2003 ( for hydrolysis/water resistance test) priming the sites, with minimum MAF+ 30% (with ten years performance guarantee) and applying masking tape after sealant is applied by mechanical means all as shown on drawing and all as specified and as directed. Note (a) The make of filler board shall be of brand "DURA board HD 100" manufactured by M/S Supreme industires Ltd or equivalent of makes listed here-in-before after. (b) The syntheitic filler board shall be premoulded compressible black in colour having minimum density of 100 (+) 10% Kg/Sqm , water abosrption less than 0.09 Kg/ Sqm and compression recovery of 93% (c) The make of polyethylene rod shall be of brand " DURA ROAD" manufactured by M/S Supreme industries Ltd or equivalent of makes listed here-in-before after (d) The polyethylene rod shall be of desired diameter having minimum density of 22 Kg /Cum and compression strength of 0.40 kg/ Sqm 25% greater than the joint Width,, of white colour (e) Primer to be used before filling sealant (f) Edge shall be levelled and jointed cut within 24 hours using diamond bit cutters of Bosch or equivalent used for cutting green concrete (g) The exposed vertical faces of slab shall be applied with one coat of white wash.

M & L for forming construction (Dummy) joints, cutting 100 mm deep with 3mm width as initial cutting and secondary cutting of 25mm deep from the top and 8mm wide using diamond cutter to accommodate polyurethane sealant backup sheet 12mm thick filled with poyurethane sealant (minimum depth of sealant above polythelene sheet shall be of 10 mm) complying with BS 4254 and En 141875 - 2003 (for hydrolysis /water resistance test) priming the sides, with minimum MAF + 30 % (with 10 years performance guarantee) and applying masking tape on edges of joint to prevant accident spillage of sealant and removing the masking tape after sealant is applied by mechanical means all as shown on drawing and all as specified and as directed. Note :- (a) The make of polyethylene rod shall be of brand 'DURA board HD 100" manufactured by M/S Supreme Industries Ltd or equivalent of makes listed here-in-before after (b) The polyethylene rod shall be of desired diameter having minimum density of 22 kg /Cum and compression strength of 0.40 kg/Sqm 25% greater than the joint width, of white colour (c) Primer to be used before filling sealant (d) Edge shall be bevelled and joint cut within 24 hours using diamond bit cutters of Bosch or equivalent used for

Suuply and fix LED High Bay Light Fitting 80 Watt with Ingress Protection level not less than IP-65, suitable to operate with 230 Volts 50 Hz single phase AC supply complete with all prewired internal components like electronic driver, surge protectors etc. and all fixing hardwares and necessary electrical connection from nearby ceiling rose / connectors all as specified and directed Make : Havells (Cat Part No SAUCER GENXPROHBP80WLED757P90DBOLTG) Crompton (Cat Part No LHB11-80-CDL/60-M) Bajaj (Cat Part No.Bajaj (Cat Part No. BGHB 80W LED GV)

S&F LED Street Light Fittings having Ingress Protection class minimum IP-65 , suitable for road lighting luminaire with high power LED and maintenance free system for capacity 20 W complete with 32 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos M.S. Flat (40mmx3mm) clamps, nuts, bolts, washers etc. all as specified and as directed. Make : Philips (Cat Part No : BRP022 LED 20 CW MR S1 PSU GR) Havells (Cat No. : ENDURAPEARLSL20WLED757SASYTOPCMP) Crompton (Cat No: LSTS-20-CDL-M) Note : The M.S. Clamps are to be painted with 2 coats of Aluminium Paint over a coat of Red Oxide Metal Primar before fixing at different positions.

S&F LED Street Light Fittings having Ingress Protection class minimum IP-65 , suitable for road lighting luminaire with high power LED with high efficiency electronic driver unit and surge protection device to ensure uniform light distribution within higher spacing between poles for capacity 45 W complete with 40 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos M.S. Flat (40mmx3mm) clamps, nuts, bolts, washers etc. all as specified and as directed. all as specified and as directed. Make : Havells (Cat No. : ENDURAPEARLNEOSSL45WLED757PASYTOPC) ) Crompton (Cat No: LSTS-45-CDL-M) Bajaj (Cat No. BRLEP 45W LED V2) Wipro (Cat No : (LR02-501-XXX-57-XX) Note : The M.S. Clamps are to be painted with 2 coats of Aluminium Paint over a coat of Red Oxide Metal Primar before fixing at different positions.

Supply & fix Wall Mounted Air Circulator fans 230 volts single phase oscillating 600 mm sweep suitable for wall mounting complete all as specified an directed. Make :- Havells (Model-Turbo Force) Almonard (Model : Marc-II) Crompton (Model VORTEX) Bajaj (Model : Supreme Plus)

Supply & fix Wall fans, 400 mm sweep, suitable for 230 volts single phase with oscillating facility complete with all mounting accessories all as specified and as directed. Make :- ORIENT (Model-44 Trendz Electric Blue) CROMPTON (Model No : HIGHFLO) HAVELLS (Model No : SWING PLATINA)

Supply, install , testing and comisionning of 2 Nos ( 1 Working + 1 Standby) factory made new Water Cooled Package type Air Conditioner of capacity 5.50 TR each, duly housed inside a weather proof enclosure with hermitically sealed scroll compressor (suitable for operation with R-407C refrigerant) directly coupled with refrigerant cooled screen protected drip proof induction motor with necessary starter and automatic modulating capacity through thermostat to achieve the inside temparature 22 degree Celcius ± 2 degree celcius with relative humidity 55% to 60% . The units shall comprising of all standard mountings and accessories along with Micro Processor based Control Panel with LCD display, Protection relays, Shell and tube type water cooled condensor with Copper tube and aluminium fins, centrifugal blower fan with air filter with in-built thermal protector, internal pressure release valves, HP /LP cutouts, complete with all internal electrical wiring and connection from main panel with suitable size cables and all interconnection between main unit and Cooling Towert, all refrigerant piping works to interconnect the compressor unit,condenser unit & evaporator unit duly insulated with suitable size sleeves of insulating material, necessary civil works for foundation of the package unit including grouting bolts and nuts and necessary M.S. Frame work to mount the condenser units as per OEM's instruction. Each unit shall be suitable to run on 415 Volt, 50 Hz AC supply and EER of the Plant should not be less than 3.3. The testing of AC Plant shall be carried out as per the clause mentioned in Particular Specification. Make : BLUE STAR / CARRIER / HITACHI

Note : The quoted rate shall deemed to be incusive of the following items : a) Suitable size of ducting made of 22 guage Plain GI Sheet with C&SS rectangular / square duct duly factory boxed, including all accessories such as corner cleat,carriage bolt,Gasket,M.S Channels & anglesof suitable size for the support of ducts, including nuts, bolts etc. and appropriate sealand on longitudinal joints etc. complete with separate ducts for supply and return air including fixing with package units with suitable canvaslinking to arrest vibration transmission between package unit and GI Ducting along with zip controlled inspection opening including insulating the GI ducts with thermal insulation by one side aluminium laminated nitrile rubber sheet complete all as specified and directed. b) Suitable size of grills / deffusers, dampers, acoustic insulation, PVC Drain pipe, 3 Phase strip heaters of capacity 12 KW. c) Panel Board indoor type, duly compartmentalized for individual switchgears / units, made of 2.0mm thick CRCA SS sheet with powder coated paint, platform mounted,suitable for working on 415 volts,50 HZ AC supply and suitable capacity switchgears / Measuring Instruments for :- i) Incoming MCCB - 01 No. (For 2 Nos Main Chillar Units and their accessories) ii) Outgoing MCCB - 02 Nos (for 2 Nos Individual Package AC Plant) iii) Outgoing MCB with DOL Starter - 02 Nos ( for 2 Nos Condenser Pumps) iv) Outgoing MCB with DOL Starter - 01 Nos (Cooling Tower Motor) v) Outgoing SPN MCB 6 Amps - 01 No (as Spare) vi) Digital Voltmeter 96mm x 96mm -01 No. vii) Separate Digital Ammeter for both the Package AC Plant with suitable rating CTs. d) Initial Charging of refrigerant gas and filling of compressor oil in boththe package units. e) Phase-I Testing of Package AC Plant to be carried out by GE in presense of contractor and shall be arranged by the contractor including providing all testing and supporting equipments for smooth conducting of test without any extra cost levied to the department. f) Phase-II Test shall be carried out by IEM/Rep of Accepting Officer followed by Summer, Monsoon & Winter Test to check the specified Temperature & Humidity control mentioned in the BOQ Item No. 10.08. The said test shall be arrangesd by the contractor including providing all testing and supporting equipments for smooth conducting of test without any extra cost levied to the department.

Supply, installation, testing and commissioning of 02 Nos (1Working +1 Standby) end-suction & top-discharge, back pullout type ,horizontal split casing centrifugal pumps for water re-circulation in condenser-Cooling Tower circuit, complete with cast iron body, bronze impeller, mechanical seals, TEFC ,fan cooled type squirrel cage high efficiency IE3 class induction motor, base plate, mounting channel frame, accessories and fittings i.e. mechanical seal,drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting of the following specifications, suitable for operation on 230 V ±10%, 50Hz, 1-Phase AC supply. [a] Capacity: 20 USGPM approx [b] Head: 10 m [c] Impeller: Bronze [d] Approximate Motor Rating: 1.0 HP Note : 1. Pumpsets will be arranged in 1 Working +1 Standby configuration. Neccessary plumbing work will be done accordingly. Cost of plumbing shall deemed to be included in the quoted rate. 2. Contractor will provide calculation of Head and Hp of Pump. In case of deviation in Hp more than specified in tender, financial adjustment will be done through DO.

Supply, install testing and commissiongin HAND OPERATED CRANE with I-Section rail of suitable dimension mounted on gantry girder over bearing plate fixed with suitable dia and numbers of nuts and bolts complete all as per manufacturer's design complete with following specifications. (a) Capacity : 01 Ton (b) Lifting Height: 4.5 M(from FFL to Bottom of Hook) (c) Span : 08 Mtr (Approximate refer architectural drawings of danger building for exact dimensons) (d) 4 Bays of 4.0M(Apprx) (e) Bridge : Single Girder I-Beam Type rolled steel Joist as per IS 807/3177 bolted to end carriage. (f) End Carriage : Fabricated with rolled steel sections/plates (g) LT Wheels : Two Nos. straight tread/type, EN 8 forged Steel, Double Flanged LT Wheels shall be provided in each of the two end carriage. These wheels shall be supported on steel axles. (h) Hoisting : Globe Brand Triple Spur Gear Chain pully Block with Grade 80 Alloy steel load chain tested at 50% overload. (i) Trolly : Overhead monorail travelling Trolley to move with the help of endless chain. (j) Operation : All operations by manual with the help of endless chain. (k) Gears : As per IS-4460, made form EN 8 and supported on ball bearings. (l) Pinion/Axles : Made form EN 9, Heat treated carbon alloy steel. (m) Bearings : Two Nos heavy duty sealed ball bearings shall be provided in each wheel for smooth running. (n) Hook : Heavy duty steel forged capable to with stand shock loads, free to swivel & ratate as per IS:8610/3815. (o) Load Chain : 8mm /2 falls, Garde 80 alloy steel as per IS-6216 (p) Hand Chain : 6 mm-Grade 30 M.S Chain as per IS-242 Make : M/s Pioneer Cranes & Elevators (P) Ltd / Dinesh Cranes / M/s Pull Mach

M& L for brick masonry valve chamber of internal dimension 1050 mm x 1050mm x 1050mm with PCC 1:4:8 foundation, 230mm thick brick walls built in CM 1:6, PCC 1:3:6 type C-1 using 20mm graded stone aggregate coping 50mm thick, plastering 15mm thick in CM 1:4 to all internal and exposed surface(upto 150mm below outer ground level) including necessary excavation and earth work in soft loose soil, MS sheet cover 3.15mm thick alongwith angle iron frame of size 40x40x6mm with locking arrangement and necessary fixing materials like hinges, bolts etc (Valve chamber cover shall be opended in two halves) and painting to MS cover and M.S.angle frame work with two coats of synthetic enamel paint over one coat of red oxide primer and 2 coats of white wash of the valve chamber both internally and externally (above GL) complete all as specified and directed.

M & L for laying brick as in protection covers over cables using well brunt sub class 'B' old size bricks in trenches over sand cushioning complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

S&F 4 Pole MCCB, 63 Amps, 16 KA, fixed magnetic and adjustable thermal relay (80%-100%) including OEM made sheet steel enclosure duly fixed inside the existing L.T Panel Board/ Feeder Pillar with necessary incoming and outgoing connections with properly lugged suitable size aluminium conductor complete all as specified an directed.

S&F 4 Pole MCCB, 100 Amps, 16 KA, fixed magnetic and adjustable thermal relay (80%-100%) including OEM made sheet steel enclosure duly fixed inside the existing L.T Panel Board/ Feeder Pillar with necessary incoming and outgoing connections with properly lugged suitable size aluminium conductor complete all as specified an directed.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1000mm width x 600mm Height (Without Canopy & Base Channel) x 450mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick / P.C.C. block pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and extended aluminium bars from MCCB for termination of outgoing cables with MCCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility .The Feeder Pillar shall be powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-54 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.15 mm thick CRCAStainless Steel sheet and 3.15 mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick / P.C.C.pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :-

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 amps, . For all internal connections from main bus bars to switch gears and switch gears to cable alley shall be carried out with suitable size PVC insulated aluminium strip as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm CONTROL WIRING :- All control wirings shall have to be carried out with 1100 volts rated FRLS grade PVC insulated (Gray Colour) multi-flexible type copper wire of cross sectional area 1.50 Sq mm and shall be properly bunched,tied and dressed, ferrule marked for proper identification and crimped with suitable size & type of tinned copper lugs and shall be wrapped with PVC spring type flexible pipes near the door hinges. INCOMING :- 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 16 KA Fixed magnetic and Adjustable thermal setting(80% - 100%) of rating 63 Amps. - 01 No OUTGOINGS :- 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 16 KA Fixed magnetic and Adjustable thermal setting(80% - 100%) of rating 40 Amps. - 02 Nos INSTRUMENTATION SYSTEM :- LED Phase Indicating light, shrouded type, 22mm, with cluster LED suitable for 230 Volts AC - 01 set of 3 lamps (RED,YELLOW & BLUE)

Note for Item No- 10.18 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks. 4) Cost of all civil work for brick / P.C.C. pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. The height of pedestal should be adjusted in such a way that the height of upper level of door should be 1.50 mtr above GL. 5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of SS Sheet for outer shell and canopy shall be of 3.15 mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

M&L for earthing complete with Galvanized Iron plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 RM deep below ground level with top edge of the plate not less than 1.5 RMs below ground level connected to GI strip of size 25mm x 4mm by means of bolts, nuts check nuts and washers of brass, connected to earthing test point all as specified incl 32 mm GI tubing medium grade and necessary fitting for protection of GI strip incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm stone aggregate reinforced with 6 mm dia TMT bar @ 75mm C/C both ways with MS handle 8mm dia, plastering 15mm thick CM (1:6) externally upto 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing and marking Bldg Nos and writing Test Results on a 3mm thick painted MS earth pit marking Plate (200mm x 100mm) duly welded with a 450mm long 10mm dia round MS rod, fixed with the earth pit chamber by grouting complete all as specified & directed.