PROVN OF HARDSTANDING FOR VEHICLE PARKING SEWAGE LINE NEAR BLDG NO P10 AND P13 TOILET AND BATHROOM CHAIN LINK FENCE AND SPECIAL REPAIR TO BLDG NO P 01 OR LINES UNDER GE NARANGI

Amount

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surfaces in soft/loose soil complete all as specified & as directed.

M&L surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil.complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removing of surplus excavated material not exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge exc. 63 mm but not exc. 100mm deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick spread, levelled and rammed including watering complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L factory made precast cement concrete Kerbs PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) in rounded or chamfered on edges and jointed in Cm 1:4 complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC (1:2:4) type B-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching including necessary formwork and finishing of exposed surfacs of concrete etc complete all as specified and as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels complete all as specified as directed.

M & L Precast RCC1:2:4 Type B-1 ( Using 20mm graded stone aggregate) as in landings, cover slabs ( for manhole etc) chullah hoods, chajjas , water toughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified as directed.

M&L for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified as directed.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified as directed.

Dismantling timber scantlings 40 sq. cm and over in section (unframed work), in any position complete all as specified & as directed.

M & L second class hard wood scantling fixed in clean sawn timber in framed work complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including builders hardware complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including builders hardware complete all as specified and as directed.

Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each and refixing in same opening complete all as specified and directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

M&L for 1.25mm thick factory made pressed steel frames of size 105x60mm with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete including PCC 1:3:6 type C-0 as in back filling of window/door frame all as specified and directed.

S&F 35 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and directed.

S&F factory made steel window with side hung shutters, glazed shutter including both side openable ( outside glazed window and inside fly proof window) including projecting type hinges with steel handle and steel peg stay complete with glazing bars and 12mm square bars or round bars of approved design welded to steel window frame dovetailed or welded complete all as specified and directed. (Guard bars or square bars shall be measured and paid seperately).

S&Fpowder quoted aluminium anodised window and ventilator shutter, side hung type without sash bars, aluminium sections weighing 0.55kg/m including necessary jointing clips , glazing clips, rubber packing, aluminium anodised snap beading, screws, fittinfs such as peg stay 150mm long ( 01 No.) hinges 100mm long type B-21 ( 02 Nos.) handle ( 01 No.) of appproved aluminium section and size complete all as specified & as directed.

M&L in repair for seccond class hard wood weather boarding , clean sawn, plain 19/20mm thick or feather edged 15/20mm thick and fixed with 30mm laps complete all as specified and as directed.

S&F 30 mm thick Factory Made Solid Panel PVC Door Shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet 5mm thick ‘C’ channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side, and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The width of stiles & rails will be in proportion to the width of the door shutter as per SSR Clause No 8B.2.1

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing etc complete all as directed.

S&F 150 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 200 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 150mm size extruded aluminium handles, febricated type, anodised complete all as specified and directed.

S&F 100mm size extruded aluminium handles, febricated type, anodised complete all as specified and directed.

S&F aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long etc complete all as specified and directed.

S & F 100mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed.

S & F 75mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed.

M&L in repair 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination,fixed with screws to timber frame work complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as directed.

S&Fin repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as directed.

Dismantling of asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridge complete all as specified & as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and directed. Note: To be executed for provision of ridges and hips.

S&Fsuspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

S&F in repairs, suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT steel bars 8mm dia and over upto and including 10mm dia , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 cm long and diameter of shank 5 to 10mm completed all as specified and as directed.

M & L mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewished not exc 15 cm long 12mm diameter of neck complete all as specified and as directed.

M & L for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and as directed.

S&F rolled mild steel plates ( plain or chequrred) channels, square cut or notched ( ordinary or counter sunk) forming holes, with riveted, bolted or welded attachment confirming to Fe-410-W (Gde-E-250) quality B complete all as specified & as directed.

S&F rolled mild steel plates ( plain or chequrred) channels, square cut or notched ( ordinary or counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde-E-250) quality B complete all as specified & as directed.

S&F Rolled mld steel roof trusses ( framed) trussed purlins, crane gantries, rails and fastenings and heavy brackets framing ( Beam, tee, angle, channel or flat section) including distace pieces, cleats etc confirming to Fe 410-W ( Gde E-250 Quality A)complete all as specified & as directed.

Supply only chain link fencing wire mesh of 100X100mm size or type, made with 4 mm dia mild steel galvanised wire complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolt etc including provision of binding wire complete all as specified and as directed

S & F galvanized two strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia bars at 75 mm spacing and straining and fixing to RCC / steel post etc., including securing or tying at crossing with and providing of galvanized mild steel wire, staples or steel pins, etc., (each line of wire to be measured separately) complete all as specified and as directed.

S&F mild steel angle iron post & strut etc. in fencing including embedding in concrete and screwing etc. including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work confoRming to Fe-290 GdeE-165 completed all as specified and as directed.

S&FMild steel framed work such as grills,gratings,etc.with ends of bars shouldered and/or riveted,or forged into spikes,framed guard bars, barred iron doors,ladders, framed balusters, walk ways,railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

Demolition of plain cement concrete (Un-reinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) including removal of spoils/ demolished materials not exceeding 50m and depositing complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floor making the surface even and smooth without using extra cement and finishing the surface with colour pigment complete all as directed.

M & L for 100 mm thick PCC 1:2:4, type B2 (using 40 mm graded stone aggregates) as in path / paving / hard standing / floor and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 typeD-2 (using 40mm graded stone aggregate) as in subase complete all as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc.complete all as specified and as directed .

M&L for 75mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in subase finished to receive floor treatment etc complete all as directed.

M&L for 75 mm thick, PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4 mtrs interval filled with bitumastic compound etc complete all as specified and as direted.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm as in vertical surfaces such as skirting/dados etc etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 375x250x7mm/300x200x7mm thick, set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps etc over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M & L pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade including 30mm thick sand cushioning and filling joints with sand complete all as specified & as directed.

M&L Machine pressed precast coloured concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade including 50mm thick sand cushioning and filling joints with sand complete all as specified & as directed.

M&L for 20-25mm thick Kota stone flooring laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for 15 mm thick rendering in CM 1:4 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 2% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specifed and directed. (Note : Water proofing compound to be measured and paid separately as "Supply only")

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer including 3mm thick wall care putty complete all as specified and as directed.

M&L for complete removal of exisring treatment of walls and applying one coat of alkali resistant primer sanding the surfaces till smooth finish is obtained and finally applying two coats of cement based paint complete all as specified and as directed.

M&L for complete removal of exisring treatment of walls and applying one coat of alkali resistant primer sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surface of wall and applying three coats of white wash on wall surface complete all as specified and directed.

M&L for preparation of new wall surface and applying two coats of acrylic exterior weather resistant paint (weather proof paint) of tint as approved complete all as specified and as directed.

M & L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

M & L for preparation of old wood or wood based surface of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of old steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paints complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane frosted on one side complete all as specified and directed.

M/L cutting chases , pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring,etc. and making good , cutting not exceeding 10cm girth complete all as specified and directed.

S&F GI tubing15 mm bore, medium grade with all fittings and fixed complete laid in floors as in spout pipe complete all as specified and as directed.

Taking out carefully the cover slab of each manhole of depth from 1.0 m to 2.0 metre and removing the sludge by mechanical process or manual process, transporting to a distance exc 250 m but not exc 500 m and depositing the same in excavated earthen pit of sufficient size and depth in any type of soil within the defence land, where directed, including returning, filling of earth in excavated pit after every disposal of sludge and also applying one coat of linsed oil and cleaning with fresh water, placing the cover slab in position complete all as specified and as directed.

S & F gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 20 mm bore GI pipe complete all as specified and as directed .

S&F 15mm dia Bib taps quarter turn cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F 15mm bore pillar taps quarter turn cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore dia of concealed stop valves cast copper alloy fancy type chromium plated with long shank and cup complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 500 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 125 mm dia chromium plated swivel type shower rose with 190 mm long chromium plated shower arm and wall flange suitable for fixing 15 mm bore iron pipecomplete all as specified and directed.

S&F fancy type Brass chromium plated 600mm long Towel Rail fixed with screws and wooden/plastic cleats etc. complete all as specified and directed.

S&Fchromium plated soap dish of approximate size 160x160x90mm embedded in wall complete all as specified & as directed.

S&F 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F 100mm bore Cast iron spun pipe soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall.complete all as specified and directed.

S&F 75mm bore Cast iron spun pipe soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall.complete all as specified and directed.

S&F 100mm dia cast iron spun bends (any radius) diminishing pieces or tapers complete all as specified and directed.

S&F 75mm dia cast iron spun bends (any radius) diminishing pieces or taper .complete all as specified and directed.

S&F Cast iron nahani trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed

S&F Cast iron nahani trap 100mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed

S&F 100mm dia cast iron spun Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches.with oval access door.complete all as specified and directed.

S&F 75mm dia cast iron spun Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches.with oval access door.complete all as specified and directed.

S&F stack clamps out of 50mm by 5mm mild steel flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75/100mm dia pipe.complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floors as in waste /soil / rain water pipe etc. complete all as specified and directed

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste /soil / rain water pipe etc. complete all as specified and directed

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and directed

S&F salt glazed stone ware gully trap, square or round mouthed type 'P' 125/100 setting and jointing with CM 1:1 complete all as specified and directed

M/L salt glazed stoneware drain pipes 150mm bore laid in trenches and jointed complete all as specified and directed.

M/L PCC 1:3:6 type C-2 ( 40mm graded aggregate) as in concrete bed to drain pipe 110/150 mm dia including packing under , and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains and making good to pipes and rendering, cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

S&F vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&Fvitreous china wash basin white flat back size 550 mm x 400mm including all fittings including cutting for and pinning in ends of brackets or erecting stand etc complete (waste coupling 32mm bore CP, 32mm bore PVC waste pipe, cast iron brackets etc shall be deemed to be included in the quoted rate) complete all as specified and directed.

S&F PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

Taking down ceiling/exhaust/wall fan including connection wires carefully, removing to store in safe custody ,painting with synthetic enamel paint by spraying incl. filling cavity and refixing the same in original position after repairing (rewinding if require) including changing the hook ,clamp ,pipe for ceiling fan as per requirement of site complete all as directed

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

M&L for point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in and including PVC Casing and Caping with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick masonite laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as per item serial No 134 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item serial No134 here-in-before but One socket outlet 3 pin 5 Amp on independent board.

All as per item serial No 134 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable.

S&F switch piano, flush type single pole one way 5 Amps 230 volt complete all as directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as directed.

S&F switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as directed.

S&F switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 16 Amp flush type complete all as directed.

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as directed.

S&F lamp holder insulated PVC/ Polycarbonate/ bakelite body, with back plate suitable for batten fitting or PVC round or squre box, complete all as directed

S&F stepped type electronic fan regulator, two module size, flush type complete all as directed.

M&L point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in concealed conduit including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as per item serial No 145 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches

S&F in repair Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed. Make:- Havells Model HEXAFT10WLED857SSYMBOPC or equivalent Model of make : Philips / Crompton /GE.

S&F in repair LED light fitting of approved make 1X 20 W, 220V, AC decorative batten type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. (Make: Crompton/ Havells/ Philips/ Jaquar or equivalant)

S&F in repair LED luminaire 600X600mm, 35/36 Watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamps suitable for roof ceiling including connecting up with three core flexible copper conductor cables of suitable size complete all as directed. (Make: Crompton/ Havells/ Philips/ Jaquar or equivalant)

S&F in repair LED light fitting of approved make mirror type with high output diffuser 2 feet, 10 W, 220V, AC decorative type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. (Make: Crompton/ Havells/ Philips/ Jaquar or equivalant)

S&F LED street light fittings of approved make 35 W 230 V AC outdoor type with high pressure diecast aluminium housing and heat resistant complete with driver, lamp, bracket with impact and corrosion resistant including thermal management in multiple optics complete wit IP 65/66 protectioncomplete all as directed. (Make: Crompton/ Havells/ Philips/ Jaquar or equivalant)

S & F in repair SPN DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or equivalent model in Siemens / Schneider

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4085 90 to 95 orequivalent model in Siemens / Schneider/L&T

S&F MCBs, SPN 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4086 09 to 17 or equivalent model in Siemens / Schneider/L&T

M&L in repair Sub main wiring with 2 runs of 4.0 sqmm, single core, FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit all together shall be measured as one unit.)

M&L building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16 sqmm 4 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, including taking out/ down the existing old cable complete all as specified and as directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 2 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Supply and lay GI tubing 25mm bore light grade for cable protection and fixing to the existing pole with flat iron clamp 25x 3mm including nut bolts complete all as specified and as directed.

Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.

M&L for sub class 'B' old size bricks laid in trenches for cable protection laid flat width wise along the length of cable complete all as specified and directed.

S&F of Exhaust fans AC single phase 230/ 240 V ,50 Hz metallic heavy body of size 300 mm sweep, 900 RPM with louver fixing with 4 no hold fastener nut and bolt with washer and connecting with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm including civil work opening on wall and making good surface complete all as specified and directed. (Make-USHA, Model-300MM S.PH TURBO HDEF 900 RPM or equivalent model of make Havells/Bajaj /Crompton)

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 .

S. R. TRADING

M/S M Ahmed and Co.