SPL REPAIR TO BLDG NO P319 OR MD ACCN AT SIG ZONE AT KALIMPONG MIL STN UNDER GE 867 EWS

S&F in repairs pre- painted galvalume aluminum zinc coating GI based steel sheet of approved profile of corrugation, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

S&F in repairs pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

Dismantling timber scantlings 40 Sqcm and over in section, in any position (framed work) all as specified and directed.

S&F in repairs false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Suspensor system (Grid) made out of GI sheet main Tee of size 23.5mmx38.50mmX0.36mm and cross Tee of size 23.5mmX23.5mmX0.36mm and angle size 19mmx19mmX0.36 mm. Grid of modular size 600mmX600mm shall be supported by 4 mm dia G.I. wire from purlins/soffit with and including 4mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8, complete all as per manufacturer's instruction. (Make : Everest or equvalent as approved by GE)

S&F joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc confirming to Fe 410-W (gde 250 quailty A) including dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to relevant IS (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 15 mm thick screed bed in cement mortar (1:6) including Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L Glazed ceramic coloured tiles size 350x 250x 7 mm/ 450x300mm/450X 350X 7mm thick setas in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15 mm thick rendering in CM (1:4) finished even and rough including Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 20 mm thick screed bed in cement mortar (1:6) including roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in vertical surface such as skirtings, dados and riser to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 10 mm thick rendering in cement mortar (1:4) including roughening surfaces of old concrete wall by picking,sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M & L Granite (of any type) work 20MM thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 20mm thick cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite demolition of old Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection/path laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges including demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work including demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for PCC (1:3:6) type B-2 (using 12.5 mm graded crushed stone aggregate) as in floor finishes complete all as specified and directed.

Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) (finished even and fair) , complete complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:4) on external wall finished even and fair mixed with integral water proofing compound @ 2% by weight of cement or in the manner specified by the manufacturer and in the proportions indicated all as specified and as directed. Note:-WPC will be measured and paid separately as supply only.

Supply only integral water proofing compond all as specified and as directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as on ceiling /chajja and RCC surfaces, finished fair and even without using extra cement complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of priming coat on newly prepared wall surfaces, including 1 mm thick layer of wall care putty (Birla white or equivalent) all as specified and directed.

M&L scrapping of existing treatment and applying two coats of 1mm thick (each layer) of wall care putty (Birla white or equivalent) and then applying two coats of oil bound distemper over a coat of priming coat after preparation of wall surfaces complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on walls complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat of white wash as in wall complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash as in ceiling complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash as in ceiling complete all as specified and directed.

M&L for preparation on newly plastered / previously untreated surfaces of wall and applying two coats of cement base paing complete all as specified and directed.

M&L preparation of old decorated surfaces of walls, chajjas and applying two coats of cement base paint complete all as specified and directed.

M&L for brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) including Demolition of brick work or stone/boulder masonary, built in lime mortar including all quions, arches, pillars etc, but excluding ashler facings, dressed stone work and precast concrete articles complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening after Resecuring or easing & adjusting complete all as specified.

Taking down chowkhats or frame not exc 1.50 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 and not exc 4 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

S&F 2 nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered , put together with glue, pinned at joints complete all as specified and directed.

S&F pressed steel frame of size 125 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges,lock ,strike plate, etc complete all as specified.

S&F pressed steel frame of size 105 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges,lock ,strike plate, etc complete all as specified.

S&F 35 mm thick second class hard wood , Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F 35 mm thick second class hard wood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to befitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete complete all as specified and directed.

S&F steel window or ventilator fixed type with glazing bar complete complete all as specified and directed.

S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed.

M&L for 18/19 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails for 19 mm thick Prelaminated particle board faces all as specified and directed.

M&L for 12 block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work complete all as specified and directed.

M&L external teak wood lipping, 6 mm thick on exposed surface for 12 mm thick prelaminated particle board fixed with nails complete all as specified and directed.

S&F 50 mm size butt hinges, medium weight , cold rolled, mild steel complete all as specified and directed.

S&F 75 mm size butt hinges, medium weight , cold rolled, mild steel complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, hold fast, kneelers, apex stones, bed plates, kerbs not provided for in roof, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed as required complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight , stainless steel complete all as specified and directed.

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F of 75 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S&F of 200 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S&F 150 mm size Aluminium handles, cast type, anodised and all as specified and directed.

S&F 125 mm size Aluminium handles, cast type, anodised and all as specified and directed.

S&F of 300 mm long aluminium alloy, anodised sliding door bolts with haps staple(bolt type), and fixing clips of sheet, cast or extruted sections and fixing bolt and sliding bolts of extruted sections or cast aluminium alloy and fixed in repair complete all as specified and directed.

S&F of 100 mm size haps and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, Knobs and rollers etc. complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

M&L preparation of new wooden surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with IS-2731 with and including suitable size of MS brackets, plug, screw all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with water closet of any type all as specified and directed.

S&F in repairs water closet (squatt pattern) of vitreous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphonic pipe etc complete including P or S trap set in and including necessary lean cement concrete complete all as specified and directed.

S&F in repairs vitreous china wash basin white of any pattern, flat back of size 450X300 mm (excluding taps), waste, chain and plug including waste pipe ,suitable size of brackets and making good the damaged walls as per existing wall finish complete all as specified and directed.

S & F in repair pillar tap Fancy Type cast copper alloy 15mm bore with capstan head, chromium plated, screwed down high pressure, with or with out lettered "Hot" or "Cold" with long screw shank and fly nuts, screwed for iron pipes complete all as specified and directed.

S&F 40 mm waste coupling of CP (half or full threaded) (Minimum weight 60 gms) complete all as specified and directed.

S&F in repair 15 mm bore PVC connection 450 mm long with two brass chromium plated brass nuts and PVC washers complete all as specified and directed.

S&F in repairs angle, stop valve 15 mm bore, chromium plated, fancy type, with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed.

S&F in repair 15 mm bore chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F kitchen plate rack made out of stainless steel 0.50 mm thick sheet with partitions and size of rack 800 x 250 x900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed.

S&F brass chromium plated tubular towel rail of 20 mm dia D' type 60cm long between flanges complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs 110 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair75 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door jointing with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door jointing with solvent cement complete all as specified and directed.

S&F of 20 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed.

S&F in repairs of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with waste pipe, plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with multi stranded copper conductor with proper colour coding drawn through and including PVC conduit (medium grade) with all fittings and accessories ISI marked concealed in wall/fixed to roof,ceiling etc incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLSH, ISI marked as earth continuity conductor (green in colour) connected to common earth dolly incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall with modular back plate and top cover for mounting switch, sockets etc including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc for one light/Bell/Exhaust fan point controlled by one, one way switch 5/6 Amps including taking down unserviceable copper/aluminium point wiring of any description including all fittings complete all as specified & as directed.

All as per item No 93.00 here in before but for one 3 point 5/6 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No 93.00 here in before but for one 3 pin 5/6 Amps switch socket outlet point controlled by one switch on independent boad.

All as per item No 93.00 here in before but for one switch socket outlet 15/16 Amps on independent board with 2.5 Sqmm multi stranded and 2.5 Sqmm stranded (for earth) PVC insulated un-sheathed copper cable all as specified and as directed.

Supply and fix Modular switch 1 way 6 A,1 module 230 Volts,50Hz, ISI marked all as specified and as directed.

Supply and fix Modular switch 1 way 16 A,1 module 230 Volts,50Hz, ISI marked all as specified and as directed.

Supply and fix Modular Bell push 6A 1 module 230 Volts,50Hz, ISI marked all as specified and as directed.

Supply and fix Bell, Ding Dong electric AC 230 Volts single pole complete all as specified and as directed.

Supply and fix Socket, 6A-2/3 pin combined 2 module 230 Volts,50Hz, ISI marked all as specified and as directed.

Supply and fix Socket, 6A/16A-2/3 pin combined 2 module 230 Volts,50Hz, ISI marked all as specified and as directed.

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply and fixing lamp holder insulated body with back plate for batten fitting all as specified and as directed.

Supply and fixing LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat sink of 10W complete all as specified and directed.

Supply and fixing LED batten surface / wall mounted with specially designed comprises of extruded channel in thermally conductive material. High transulucent serrated milky white diffuser used to grt glare free and smooth light distribution. power consumption 20W, system efficiency of ≥100 lumens/W, Ingress protection IP 20, colour rendering index CRI>80, driver efficiency>85%, power factor > 0.90, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50,000 burning hrs (min) as per IEC standard all as per specified and directed.

Supply and fixing LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired up to terminal block, power consumption 10W, system efficiency of ≥100 lumens/W, Ingress protection IP 20, colour rendering index CRI>80, driver efficiency>85%, power factor >0.90, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50,000 burning hrs (min) as per IEC standard all as per specified and directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED light fitting 1x9W/1X10W IP66 & IK09 integral LED Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing wall mounting, brushed nickel finish fixture with acrylic diffuser suitable with 9 W LED lamp B22 base complete all as specified and directed.

M&L for sub main wiring along with earth wire of size two run of 4 sq mm + one run of 4 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLSH including drawing into 25 mm PVC conduit concealed in wall/roof including taking down of old unservicible sub main wiring complete all as specified and directed. (Note: Three run of 4 Sq mm copper wire including one run of 25 mm of size PVC condute shall be measured as one unit length).

M&L in repairs for sub main wiring along with earth wire of size two run of 6 sq mm + one run of 6 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLS including drawing into 25 mm PVC conduit concealed in wall/roof complete all as specified and directed.(Note Three run of 6 Sqmm including one run of 25 mm of size PVC Conduit shall be measured as one unit length).

Supply and fixing in repairs TPN DB with suitable for TPN MCB incomer, double door (IP-54), 4 Ways, built- in 100 Amps busbar for neutral link complete suitable for 415 Volts, AC, 50 Hz, flushed in wall or fixed on surface complete all as specified and directed.

Supply and fixing in repairs Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 100 Amps rated Single pole and neutral linkof 8 way 240 Volts AC, concealed in wall complete all as specified and as directed.

Supply and fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of TPN 40 To 100 Amps. capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of DP 40-63 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing in repairs 240V, 10KA 'C' curve miniature circuit breaker (MCB) of DP 32 AMP capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 5 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

S&F metal plug socket single pole and neutral encloser with two pin earth plug with 01 No MCB SP 20 Amp with C series complete all as specified and as directed.

Taking down Exhaust fan steel body any make any size and keep in safe custody,refixing the same in repairs with all accessories and necessary fixing arrangements, AC single Phase. 230V including blades, and frame and louvers. complete all as specified and directed.

Supply and fixing electric water heater storage type wall hanging mounting type with powder coated metallic body BEE 5 Star rated with diamond glass lined inner tank with maximum operating pressure of 8 bars incuding factory fitted thermostat maximum 75 Celsius with automatic thermal cutout and multifunctional saftey valve inculding suitable nuts & bolts for fixing arrangement operates on 230V ,maximum power consumtion -2kW of capacity 25 Ltrs , with all accessories and connection pipe 15mm bore 2 Nos for hot and cold water supply,geyser saftey cord with 16Amps ELCB complete including taking down old u/s Geaser & deposit to MES Store complete all as specified and directed. . Havells Cat Part No : Monza Nu GHWAMUSWH025 or equivalent Racold, Bajaj

Taking down Electric KWH meter and keep in safe custody and refixing the same including testing on completion complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC (1 : 3 : 6) type C-1 , 50 mm thick pre cast RCC (1 : 2 : 4) type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I and as directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 Core, including glands, lugs, nut, bolts, washers as required at site, testing including taking down existing complete all as specified and directed.

Excavation in trenches/ foundation in soft/ loose soil not exc. 1.5 metre wide and n'exc. 1.50m deep for LT under ground cable/pole foundation and getting out including forming bottom surface to required level or slope, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exceeding 25cm each layer all as specified.

Removing excavated material not exceeding 50M and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified.

M&L Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick.

S & F in repairs Steel pipe glavanized light grade of 40 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

Please Enable Macros to View BoQ information