Special repair to SEMT Bldg, bathroom of D platoon (P-675) of CTW, provn of cloth drying hangers at certain OTM accomodations and Provision of tiling and sanitary fitments in toilet of certain bldgs of INI at CME, Pune

Amount

Demolition of brickwork or stone/ boulder masonry & pcc block masonry built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and directed.

M&L precast solid block masonry of block in precast cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key, scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L 15mm thick cement plastering on concrete surfaces in CM (1:4) finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat of primer on walls over and including 3mm thick wall care putty to get smooth surface complete all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced ) of any description and in any position not otherwise specifically provided for etc. complete all as specified and directed

M&L for 75mm thick PCC type D-2 (1:4:8) using 40mm graded stone aggregate as in sub base etc complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6. complete all as specified and directed

M& L rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

S&F Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed all as specified and directed by Engr - in - charge.

M&L vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directed

M&L glazed ceramic coloured tiles in vertical surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over a backing coat of cement mortar etc. complete all as specified and directed.

M&L vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat of cement mortar etc complete all as specified and directed

Taking down chowkats or frames with shutter(without taking off shutters from the frames) not exc. 1.5 sqm each and removing from site complete all as sepcified and directed.

All as per item No.17 above, but exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed.

S & F powder coated aluminium sliding windows three track with two glass shutters using 5 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete all as specified and directed Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

M & L for Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube etc all as specified and directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed.

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21.

S & F 125 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No.26 above, herein before but 20mm bore

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specifeid and directed.

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Labour only for Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed

All as per item No.30 above, herein before but 20mm bore. Note for Sl item No.30 & 31 : The serviceable tubing obtained from sl item No. 26 & 27 shall be re-used in these items.

S&F in replacement fixed type partly panelled & partly glazed partition using 25 x 37.50 mm (DP) aluminium section No.20034 in frame and section No.19361 and 19352 in panels including 4mm thick plain glass & 12mm thick prelaminated particle board with decorative choice lamination on both sides fixed with aluminium cleats etc complete all as specified and directed.

S&F in replacement partly panelled & partly glazed door single/double, leaf, using aluminium section Top - 19528, Middle - 19575, Bottom - 19530, Vertical - 19526 fixed with aluminium floor door spring, pivot etc., with particle board panels of 12mm thick prelaminated particle board with decorative choice lamination & 5mm thick plain glass having interlock (20939), Handle (20602) complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm, cross tee of size 24mm x 28mm x 0.7 mm using purpose made members interlocking to each other and 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction including taking down old ceiling Make of GI Grid work : Armstrong/Swastik/Techno Grid Make of 'E' board : Everest/Indian Gypsum/Armstrong or equivalent approved .

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed

All as per item No.37 above, but bedded in lime or cement mortar complete all, as specified and directed.

Dismantling battens for tiles, shingles etc. of any size including tilting fillets spacing exc 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

M&L roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed

All as per item No. 42 above, but except tiles Note : The serviceable tiles obtained from sl item No. 37 & 38 shall be re-used in this item.

M&L ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6

All as per item No. 44 above, but except tiles Note : The serviceable tiles obtained from Sl item No. 37 & 38 shall be used in this item.

S&F For 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 etc. complete all as specified and directed.

All as per item No. 46 above, but except sheet Note : The serviceable sheet obtained from Sl item No. 41 shall be used in this item.

S&F For 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc. complete all as specified and as directed.

All as per item No. 48 above, but except plain sheet Note : The serviceable sheet obtained from Sl item No. 41 shall be used in this item.

S& F second class hard wood battens at 30 cm centres of sec. area exc. 15 cm but not exc 25 etc. complete all as specified and directed.

All as per item No. 50 above, but except battens

S&F for second class hard wood, clean sawn timber scanttling etc. complete all as specified and dierected

S&F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 110 mm PVC (SWR) bend any radius complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Framed work such as roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed.

S & F for 1.25 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc. complete all as specified and directed.

Surface Preparation: Minor cleaning work, removal of loose concrete and filling cracks with polymer modified mortar using SmartCare SRP Making of angle fillets all around the periphery of the wall with polymer modified mortar using SmartCare SRP. Pipe Downtake Treatment: Supplying & grouting the gaps around the pipe / inserts with SmartCare General Purpose Grout, a non shrink cementitious waterproof grout. The “Nahani” trap, etc is to be fitted securely in the same manner & the gaps around it to be grouted with non shrink Grout. This shall conform the following standards: ASTM C 109 - 1999 18, ASTM C 1107, Grade C complete as per instructiions. Providing 3 coats of SmartCare Ultron and 40-50 gms polyester fleece sandwiched between 1st and 2nd coats completely up to the top edge of the pipe etc. complete as per manufacturer's instructions Waterproofing Coating: Supplying and applying High performance hybrid polyurea elastomeric waterproofing coating cold applied of spray / brush applied, SmartCare Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, shore A Hardness of min. 75 as per ASTM D 2240. The system includes final base preparation, 1 Coat of SmartCare epoxy primer application @ 150 Gm per SQM and applying SmartCare Ultron in two coats at 1.2 kg per Sqm etc, complete as per Manufacturer specifications.

Note: The application must be done by authorised applicator agency registered in SmartAssure Service. The 10 Year warranty documents needs to be submitted by such an applicator on Rs. 500 stamp paper along with security deposit of Rs. 5000/- in favour of GE (CME) Kirkee for the warranty period

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding, removing and rubbish off the premisses complete all as specified and directed.

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for 20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc. complete all as specified and directed.

M & L machine cut Kota stone slab flooring 20-25mm thick over screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L machine cut Kota stone slab flooring 20-25mm thick as in steps, skirting, dado etc. over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for cement concrete work in pavement/ hardstanding of flexural strength 40 Kg/ square centimetre in field using 400 Kg of cement per cubic metre, thickness of concrete 35 cm or more etc complete all as specified and directed.

M & L for forming construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' etc. complete all as specified and directed.

M & L for forming construction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' etc. complete all as specified and directed.

Finshing surface of concrete roads, pavements, by belting etc. complete all as specified and directed.

S & F for TMT bars 20 mm dia at construction joint cut to length and bent to shape as required etc. complete all as specified and directed.

M&L treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors

M&L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coat of Oil bound distermper white or tinned over one coat of primer on walls, etc all as specified and directed.

All as per item No.70 above, but two coats of white wash on ceiling complete all as sepcified and directed.

All as per item No.70 above, but two coats of cement base paint without wall care putty complete all as sepcified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq. m in each pane

Removing building materials etc. Out of CME area, including loading, unloading and stacking at the destination and exc. 5.00 KM, etc. complete all as specified and directed by Engr - in - charge

Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

Dismantling water tanks and removing, capacity exc. 500 & not exc. 1000 ltrs complete all as specified and directed.

S&F 1000 ltr. Capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L cement concrete type E-2, 1:5:10 (40 mm graded stone aggregate) lean concrete as in sunkun floor for filling etc. complete all as specified and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sunkun floor complete all as specified and directed.

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L Polythene film black 50 micron laid in floor complete all as specified and directed.

Cutting chase, pinning in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills, sunshades, shelves, lintels,etc and cutting chasesfor concealed water tubing and making good, cutting not exc. 10cm girth in brick walls complete all as specified and directed.

M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral WPC all as specified and directed.

M&L For 25 mm thick, type B-1, 1:2:4 (20mm graded stone aggregate) as in sub base etc complete all as specified and directed.

Rounding to edges of stone slabs, such as in steps, cooking platform and other similar situation complete all as specified and directed.

S & F under counter wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover 'P' or 'S' trap, flush pipe complete all as specified and directed

S&F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S & F in repiars Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) with flush pipe complete all as specified and directed.

S&F in repair brass chromimum plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc. complete all as specified and directed.

S & F brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and directed.

S&F in repair 15 mm dia Fancy pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long shanks and flynuts, screwed for iron pipe complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 75mm PVC (SWR) bend any radius complete all as specified and directed

S&F in repair 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

All as per item No.101 above, but 110mm bore of pipe complete all as specified and directed.

M&L in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item No.103 above, but 110mm complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

All as per item No.105 above, but 110mm complete all as specified and directed.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S& F in repair stainless steel Soap dish holder complete fixed to wall as specified and directed by Engr-in-Charge. Make :- Cera code No. 50061606 or equivalent of Jaquar/ Seico Indus/ Zoloto

S&F in repair stainless steel toilet paper roll holder with flap complete all as specified and directed. Make :- Cera code No. 5006110 or equivalent of Jaquar/ Seico Indus/ Zoloto.

Supply and fixing steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, MS 10mm square guard bar, Glazing bar dovetailed or welded for receiving glass and including cutting holes in wall for fixing the window with hold fast in PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) and makding good the disturbed surfaces in CM (1:4) and with the existing finishes to match complete all as specified and as directed.

Supply and fix 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L for preparing new surface of wood of any decription , not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminous paint and sanded complete all as specified and directed.

Preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc. 0.1 Sqm each complete all as specified and directed.

M & L Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

S & F Mild steel butt hinges medium weight, cold rolled, 100mm, ISI marked, complete all as specified and directed.

M&L barrel tower bolts stove enamelled black of size 200 mm complete all as specified and directed.

M&L barrel tower bolts stove enamelled black of size 150 mm complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

M&L for Securing 3 mm glass Sheet glass, ordinary quality, in squares not exc. 0.5 sq. m each in existing metal frame glazed with putty/ beads including removing loose or decayed putty/ beads, painting /oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying complete wall with 3 mm POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L complete removal of existing treatment and applying two coat of Oil bound distermper white or tinned over an coat of primer on walls, etc all as specified and directed.

Chipping off loose concrete/plaster upto sound stratum of RCC members such as slab, chajjas, columns, beams and clean the surface with wire brush, washing down with water using water jet including necessary scaffolding & propping to support the structural members where work is to be executed and removing debries to a distance exc. 250 metre but not exc. 500 metre.

M & L for providing and applying rust inhibition coat system (in two coats) as per manufacturer's instructions to exposed reinforcement after cleaning and removing scales and rust complete all as specified and directed by Engineer-in-charge.

M & F for providing and applying a bond coat (epoxy based bonding materials) to all exposed concrete surfaces all as per manufacturer's instructions complete all as specified and directed by Engineer-in-charge.

M & L for providing and applying latex polymer modified cement mortar in specified composition of sytem [ i.e. cement 400 parts by weight, quartz sand 1600 parts by weight, polymer 60 parts by weight, water 120 parts by weight] to RCC surfaces all as per manufacturer's instructions complete all as specified and directed by Engineer-in-charge.

S & F ready made pully operated clothes drying system incl of four aluminium pipes of 2.70 RM long each (4 pipe set), outer dia 22mm and inner dia 19.8 mm channel assembly, locking system ropes and all fixing materials complete all as specified and directed. Make: Easy dry or equivalent make as approved by CE Sourthern Command Pune

S & F for L angle 31" long, made of 20mm square MS pipe, powder coated with provision for fixing 4 pipes with 4 holes for mounting provided with mounting nails etc complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floor and paving not exc. 15cm thick below or above ground level complete all as specified and directed

M & L cement concrete type C-2 (1:3:6) using 40mm graded stone aggregate as in floors plinth protection, path etc. 75mm thick smooth finished surface without using extra cement complete all as specified and directed.

M & L joint free Non Skid glazed ceramic tiles (coloured) 7 to 8mm thick (Square/ rectangular) area of each tiles exc. 0.11 Sqm but not exc. 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for stall ceramic urinal pastel coloured of size 720x485x310mm (make: Hindware Cat No. 60006 or equivalent approved make indicated in list of makes in tender) i.e. toughned glass (including grinding, polishing, rounding/ moulding/ chamfering edges) brass CP bottle trap, electric operated auto censor flushing arrangements (Make : Hindaware Cat No. 500963 or equivalent approved make indicated in list of makes in tender) omplete all as specified and directed.

Supply and fix in repairs Vitreous China bowl urinal flat back, size of 465x355x265 mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe

M & L for coupled closet (Clover) snow white make Cera including P or S trap alongwith cistern dual flush complete set and soft close plastic seat cover complete all as specified and directed including taking down old unserviceable one complete all as specified and directed.

Supply and fixing in repair vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling, waste pipe complete all as specified and directed.

S & F in repairs Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25 mtr long flexiable tube and ABS wall hook incl making connections and fixed in position complete in all respect as complete all as specified and directed.

S & F in repair brass CP pillar tap long neck with 450mm long braided hose chrome finish complete all as specified and directed. Make:- Jaquar Cat No. DRC-37001 or equivalent approved make indicated in list of makes in tender.

S & F in repair 15mm dia concealed stop valve chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

M & L for urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms

Supply and fix in repairs Brass chromium plated bottle traps for wash basins with inlet and oulet screwed for pipe or connections including necessary packing, union and cap and fixed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar.

S & F in repairs PVC (SWR) branch pieces, single (single 'Y') equal or unequal 110 mm bore provided with access door complete all as specified and directed.

S & F in repairs PVC (SWR) branch pieces, single (single 'Y') equal or unequal 75 mm bore provided with access door complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and re-fixing in position (cleaning repairing etc. measured separately) capacity exc. 500 and not exc. 1000 ltrs complete all as specified and directed.

Supply & fixing 750 ltr capacity rotational moulded polythlene water storage tanks (Cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete screwed for iron pipe or brass ferrule complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc for the following :-

One light/ fan/ exhaust fan/ bell point controlled by one switch and one regulator

Socket outlet, three pin 5 Amps on the same board

Socket outlet, three pin, 5 Amp, independent

All as per item No.152 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 Amps socket outlet flush type on independent board.

S & F switch piano, flush type, single pole one way 5 amps complete all as specified and directed.

S & F switch piano, flush type, single pole one way 15 amps complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 amps flush type complete all as specified and directed.

S & F socket outlet 5 in 1, 5 pin, 15 amps flush type complete all as specified and directed.

S & F lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complete all as specified and directed.

S & F ceiling rose, 3 terminal PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed.

S & F Decorative ultra slim with polycarbonate housing with high lumen output environmental friendly, energy efficient ready to use pack surface and wall mounted LED batten (LED tube light fitting complete 22W) with integrated electronic driver and 02 No PVC square blocks incl taking down old UNSV fitting.

S&F LED panel 2 feet x 2 feet size 36 wattt glare free symmetrical including driver and taking down old UNSV one complete all as specified and directed.

S&F corvi neo new generation energy saving LED Bulk Head Neo 10 Watt made up of Poly carbonate housing with diffuser incl taking down old UNSV fitting. Make- Surya cat No Corvi Neo SLE BH 10W or equivalent of Philips/Bajaj

M&L for sub main wiring with two run of 6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC Conduit of desired colour not less than1.2 mm thick and 25 mm wide & 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly incl taking down old unserviceable one complete all as specified and directed

Taking down ceiling fan of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing, painting etc including providing flexible three core from ceiling rose to connector of fan

S & F MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one.

S & F MCB distribution board double door 240 volts 12 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

S & F MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one complete all as specificed and directed.

S & F MCB SPN 40 to 63 Amps, 230 V, AC incl taking down old unserviceable one complete all as specificed and directed.

S&F enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

S&F in repairs casing and caping 80 mm PVC body super finished with accessories for replacement of old circuit

S&F switch Modular, one way 6 Amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F switch modular one way 16 Amps, 1 module with suitable plate and cover complete as per existing make and model all as specificed and directed

S&F socket modular 6A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

S&F socket modular 6A/16A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

S&F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting.

S&F surface and wall mounted LED batten (LED tube light fitting 10W), extruded aluminium housing provided for efficeient heat dissipation with polycarbonate diffuser & integrated electronic driver alongwith LED tube 10 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting. Make : Havells cat No. ENDURALINEARNEOBS10WLED830SPCWH or equivalent of Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar.

S&F MCB distribution board double door 240 volts 4 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

S & F MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one.

S & F MCB SPN 40 Amps, 230 V, AC incl taking down old unserviceable one complete all as specfied and directed.

M & L for earthing complete with GI earth plate electrode of size 60 x 60 x 0.6 cms thick burried directly in ground vertically at a depth of not less than 2.25 Mtrs below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanised iron strip of 25 x 4 mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, 40 mm dia GI tubing light grade protection pipe upto test point, 20 mm dia GI watering pipe with funnel and wire mesh, PCC pit 1:3:6 with pit cover of size 30x30 CM made of RCC 1:3:6 with suitable handle, frame of angle iron size 40 x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling in all as required at site all as specified in plate No 3 of SSR Part-I and directed by Engr-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm

Mukund Engineers and Contractors

N AND G CONSTRUCTION

vishalconstruction