PROVISION OF DWARF WALL HARD STANDING AND SCOOTER CUM CYCLE PARKING SHED ADDN/ALTN AND SPL REPAIRS TO OFFICES OF NAVPEN DEMOLITION OF AND RECONSTRUCTION OF SECURITY SENTRY POST BEHIND URC AND CERTAIN REVENUE AND MINOR WORKS UNDER GE (NW) MANKHURD

Amount

Surface dressing n.exc 15cm deep and getting out in average soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and directed.

M&L Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete and surrounding posts complete all as specified and directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 or IS-4293-1979 of IS grade St-240 etc complete all as specified and directed.

M&L for broken stone or boulders hardcore of guage n.exc 63 mm depositing, spread and levelled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed.

M&L 100 mm thick plain cement concrete type B-2, 1:2:4 (using 40 mm graded aggregate) as in flooring finishing cement concrete surface even and smooth using extra cement 3.0kg/sqm and spike rolling to surfaces complete all as specified and as directed

M & L two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of previously untreated surfaces of steel and iron exc 10 cm width or girth complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating (55% aluminium + 43.5% Zinc+ 1.5% Silicon) GI based corrugated steel sheets as in roofing/wall cladding, 0.50mm thick (total coated thickness) of colour as directed by GE, conforming to AS-1397/ASTM A-792 and having tensile strength minimum 550 Mpa fixed with and including hot dip galvanised, self drilling and self tapping screws neoprene and EPDM washers as per manufacturer's instructions, complete all as specified and directed.

Demolition of brick work /stone bouldersbuilt in cement mortar including all quins, arches, pillars etc complete all as specified and as directed.

Excavation over areas not exc 1.5m deep in hard/dense soil for foundation etc. and getting out, complete all as specified and directed.

M&L for approved Moorum brought from outside MD land by spreding in s, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering and surface formed rolling with power roller exc 8 tonne and not exc 12 tonne and finished to required level/grade etc complete complete all as specified and directed

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, as in wall etc complete all as specified & directed. Note: Face work shall be measured and paid separately complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 20 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course complete all as specified and directed.

M&L 15mm thick rendering in cement mortar (1:6) on brick/concrete surfaces of walls, finished even & smooth surfaces without using extra cement and with thin layer of sagol finish complete all as specified and directed.

M& L Pre Polished Chequred cement concrete tiles 30cm x 30 cm x 25 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey white cement in equal proportions over screed bed or bedding layer 20 mm thick in cement mortar 1:6 complete all as specified and as directed

M&L for pre cast cement concrete block masonry with solid block of grade (C-5) having block density not less than 1800 Kg/cum, exc, 10cm in width and setting in CM 1: 6, complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded agg as in coping all as specified and directed.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in excavated soil complete all as specified and as directed.

Removing and disposing off the excavated material/soil out side MD Land, complete all as specified and directed.

S & F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S & F Rolled Mild Steel Framed work as in doors or Gates of angle or other section confirming to Fe 410 - S, with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete all as specified and directed.

Cutting holes Superficial area Exc 250 sq cm but n exc 500 sq cm into or through cement concrete slabs, chajjas, etc. reinforced or otherwise complete all as specified and directed.

M & L Rendering 20 mm thick on fair faces of brick work or concrete surfaces using CM 1:4, finished the surface even and smooth all as specified and as directed. Note : WPC shall be measured separately

Supply only integral water proofing compound complete all as specified and directed.

M& L for preparation of new plaster/concrete surface of walls, chajjas, soffits & beam including necessary scaffolding and applying two coats of 100% anti fungal acrylic exterior emulsion paint over a coat of primer including necessary scaffolding up to 24 m height, complete all as specified and directed.

Dismantling stone slabs of any description or thickness in floors, aprons etc all as specified and directed

Supply only 12 mm thick prelaminated particle, board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to aluminium frame work complete all as specified and directed.

M & L for brick work in CM (1:6) using sub class 'B' bricks strainght or curved as required on plan exc 6mtrs mean radius etc complete all as specified and directed.

Demolition cement concrete( reinforced )in any description and in any postion not otherwise specifically provided complete all as specified and directed.

M&L for 35 to 40 mm thick machine cut, prepolished cuddappa stone slab as in plateform for fixing oval shape wash hand basin(including cutting the slab to oval shape to accomdate the WHB), pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc,also including moulding/rounding to edges of the slab, complete as specified and directed.

M&L for 20 to 22 mm thick Black Jet, premium quality, Granite Slab (table rubbed and polished) as in plateform for fixing sink, wash basin etc (including cutting the slab to oval shape to accomdate sink , moulding,etc), pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc,also including moulding/rounding to edges, laid over and including 15mm thick cement mortar 1:4 screed, complete as specified and directed.

S&F in repairs stainless steel sink with drainage board made out of 1.00mm thick Sheet of stainless steel grade A1S1 305 for kitchen or laboratory with and including plugs, washers, wastes,40mm bore PVC waste pipe, overall size 915mm*460mm with bowl size 410mm*330mm*160mm, also including bedding in cement mortar to dwarf wall or provision of fixing brackets and connecting union to pipe, complete all as specified and directed.

M&L for prepration of newly plaster surface of wall and applying two coat of distemper oil emulsion on walls with one coat of primer (chalk white on plastered surfaces) complete all as specified and directed

M&L for non skid coloured ceramic tiles 400x400x6 to7mm thick in floors etc set and jointed in neat cement slurry and pointed with coloured cement to match the shade complete including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

S&F stainless steel electro polish of grade 202 as in kitchen trolley for modular kitchen consisting of cutlery cup / soucer, thali basket, drawers, plain basket, bottle pullout basket etc, complete all as specified and directed. Note : The design and specifications of the above item (including of materials) shall be got approved by the contractor from the GE before procurement

M&L for 18/19 mm thick marine ply bonded with undiluted Phenol Formaldehyde resin, Boiled Water Proof, Specific gravity 0.80 (minimum), moisture content 8-12%, water absorption <5%, provided with and including 1mm thick plastic laminated sheet on both sides of plywood (plastic laminated sheet shall be with decorative choice lamination on one side and other side balancing) as in kitchen cabinets, cub board, shelves etc, Fixed with screws to frame work, complete all as specified and directed. Note: Payment for glass panels shall be made for separatly as "supply only".

S&F D-handle of size 96mm long of stainless steel with matt or gloss finish for modular kitchen shutters, complete all as specified and directed.

S&F continuous (piano) hinges, width of flap 30mm (when open), mild steel, bright finish or electro-galvanised, complete all as specified and directed.

Supply & fix 15 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 75 mm bore uPVC (SWR) Bends/Shoes with and including rubber ring joints, complete all as specified and directed.

S & F 75 mm bore uPVC (SWR) soil, waste, ventilating rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary stay clamps etc, including taking down existing SWR pipes(including fittings) of any description, complete all as specified and directed.

S&F in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed.

S&F pillar cock (Swan neck), fancy type, long body with wall flange, screwed for iron pipe or for brass ferrule 15mm bore of make Jaquar or equivalent of make KOHLER or MARC as approved by the GE, complete all as specified and directed.

S&F cast iron Nahani trap 100mm dia out let including grating connecting, jointing to waste pipe with lead joints, including embedding the same in PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

M& L for preparing old surfaces walls of distempered & painted surfaces and applying one coat of oil bound distemper complete all as specified and directed.

M&L 40 mm thick plain cement concrete type B1, 1:2:4 (using 20 mm graded aggregate) as in subbase of flooring complete all as specified and as directed

S&F Angular stop cock with wall flange, fancy type, Make Jaquar Code No FUS-29053 or equivalent of make KOHLER or MARC as approved by the GE for iron pipe of 15mm bore, complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubish off the premises complete all as specified and directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm not exceeding 4.0 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

Supply and fixing hot dipped GI imposed grid with 24mm wide T sect exposed flanges powder coated frame work comprising of main runner made from 0.33 mm thick GS sheet of size 24mmx32mmx3000 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug,level adjusters and screws etc flush fitting of 1200mm long cross tee interlocked between main runners @ 600mm c/c to form 1200mmx600mm modules cross tee longer than 600 mm to be supported independently 600mmx600mm modules shall be formed by fitting 600mm long cross tee centrally between 1200mm cross tee ,peremeter wall angle shall be GS of size 19mmx19mm and 0.45 mm thick 300mm long including 600mmx600mmx8 to 10mm thick PVC laminated armstrong gypsum board complete all as specified and as directed.

S&F Vitrified Light shade ceramic tiles 10 mm thick (square/rectanglar) polished area of each tile not exceeding 0.36 sqm ,in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to matched laid over 15mm thick badding layer of CM 1:6 complete all as specified and as directed.

All as per item No 54 but as in skirting /dado laid over 10 mm thick bedding layer of CM 1:4 complete all as specified and as directed

S&F for aluminium (Die cast body) hydraulically door closer regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed as in repairs complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Taking up or down steel water tubing and connections of size 15mm bore, complete all as specified and directed.

M&L cutting chases in brick/stone wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends of edges of landings,steps, cills.sunshades, lintels etc. and cutting chases for concealed water tubing and making good ,cutting not exc 10 cm girth complete all as specified and as directed.

Supply and fixing of 20 mm outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings (including provision of special fittings i.e. brass elbow, brass tee, male brass threaded adaptor, female brass threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) fixed on the surfaces of walls/ceilings or laid in floors etc and drilling in walls etc and making good the surfaces in CM 1:3 after fixing of pipes/fittings,including dismantling old GI pipe complete all as specified and directed.

M&L for 300x300x 7-8 mm thick non skid Digital dark coloured Tiles as in floors over screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

M&L for Digital coloured wall tiling of 300x600x 7-8 mm thick on vertical surfaces, skirting/dados etc. over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white / coloured cement to match the surface complete all as specified and as directed.

S&F in repairs 15 mm bore angular stopcock with wall flange of make :Jaquar cat No Fus-29041 or equivalent in Kohler or Marc complete all as specified and as directed

S&F in repairs 15 mm bore two way Bib cock long body with wall flange of make :Jaquar cat No CON 041KN or equivalent in Kohler or Marc complete all as specified and as directed

S&F in repairs hand shower (health Faucet) of make :Jaquar cat No ALD-CHR-565 or equivalent in Kohler or Marc with 8mm dia 1 mtr Long easy flex tube in chrome finish & wall hook complete all as specified and directed.

S&F 15 mm bore bib cock Auto closing system with built in control cock with wall flange of make Jaquar cat No PRS -043 or equivalent in Kohler or Marc complete all as specified and as directed

Supply only chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

S & F in repair Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed

S&F vitreous china, table top wash hand basin oval shape of size 420x420mm x135 as per cat No : ARS-WHT-0538 Make of JAQUAR or equivalent make mentioned in PS fixed on granite counter top slab including brass chromium plated full threaded waste coupling with grating 32mm dia PVC waste pipe including removing old wash basin complete all as specified and directed. (Note: Granite slab, RCC plat form, brick wall support etc shall be measured and paid separately)

S&F 15 mm bore urinals valve of make Jaquar Cat No:PRs-077 or equivalent in Kohler or Marc auto closing system with built in control cock & wall flange (pressmatic) long screwed shanks and fly nut screwed complete all as specified and as directed

S&F in repairs Pedestal pan Couple closet Cat LYS-WHT-0204BS of Jaquar or equivalent in Kolher/Macrc and soft seat cover cat No ZPS-WHT_1027UF of Jaquar or equivalent in Kohler or Marc including removing old WC complete all as specified and as directed.

Supply & Fixing solid PVC door frame of size 50 mm x 95 mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube and edges will be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutters with particle board core 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F 100 mm long stainless steel butt hinges fixed with stainless screw complete all as specified and as directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length complete all as specified and as directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms)

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MD land, complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement, complete all as specified and directed.

M&L for PCC 1:2:4, type-B1, using 20mm graded stone aggregated as in sub base of floors and for any other propose in any location mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: Supply only WPC will be measured and paid separately.

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fibre glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. Notes :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

S&F in repairs CP grating doom 125mm dia of size complete all as specified and as directed.

S&F Toilet roll holder with flap of make Jaquar cat no AKP-35753P or equivalent in Kohler or Marc complete all as specified and as directed.

S&F 6 mm thick glass mirror of size 450x 600 mm fixed with screws, making good the distrubed surfaces to match the existing all as specified design is approval by Engr-in charge

S&F 40mm bore Low density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed to walls. Ceilings or in floors etc complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

M&L bottle trap of 40 mm bore brass , chromium plated for wash basin complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

S & F in repairs aluminium anodised grill of approved design and including fixing with U clip or F section beading complete with all fitting and fixture and drilling required in RCC section in rectangular or arch type balcony opening of the building complete all as specified and directed.

Excavation in trenches,n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and getting out in any type of soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundations,filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete in M-30 (DESIGN MIX) (using 20mm graded aggregates) for footing foundation and plinth beams etc complete all as specified and directed. Note of item No 92 to 96 :- Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune/ any NABL approved lab/ Govt Engg College

M&L for reinforced cement concrete (Design mix) in M-30 (using 20 mm graded aggregates) in columns/pillars/post/struts complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) in M-30 (using 20mm graded aggregate) for beams, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) in M-30 (using 20 mm graded aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings cupboard slabs and in shelves and the like etc complete all as specified and directed.

M&L for reinforced cement concrete type (design mix) M-30 (using 20 mm graded stone aggregate) in chajjas and the like complete all as specified and directed.

Use waste of formwork to rough finished surfacce of side of concrete foundations and plinth beams and similar work vertical or to batter for flat and fair finished surfaces all as specified and directed.

Use waste of formwork to rough finished surface of concrete of side of pillars, posts, struts, piers, columns and stanchions for square, rectangular fair finished surfaces all as specified and directed.

Use waste of formwork to edge of concrete flat,treat break in floors,window cills, concrete railling, opening in concrete wall ,floor and roof n.exc 20cm wide and side of RCC bands in walls, horizontal or sloping and similar work exc 10 cm and n exc 20 cm wide fair finished surfaces. and complete all as specified and directed

Use of waste of formwork to side and soffits of rough finished surface of concrete of floor or roof beams and lintels, cantilevers,overhanging etc.fair finished surfaces complete all as specified and directed.

Use waste of formwork to fair finished flat soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc 200 mm thick complete all as specified and directed.

Use waste of formwork to fair finished flat surface to chajjas, water troughs and similar items including edges complete all as specified and directed.

M&L for CRS TMTsteel bars 10mm dia and over, cut to length, bent to shape required,including cranking bending spirally for hooping for columns,hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Item No 103 but 5mm dia and over upto including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for 15 mm thick polymer modified ready mix cement based plaster on fair faces of bricks or concrete surface including necessary scaffolding upto 24m height etc complete all as specified and directed.

M&L for 8 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed Note for item No 105 & 106 : (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) This item shall be operated only for the locations where the thickness of existing adjoining plaster is to be matched

M& L for 3mm thick wall care putty on ceiling surface finished even & smooth complete all as specified and directed.

M&L for preparation of newly plastered surfaces of celings and applying three coats of white wash complete all as specified and directed.

S&F standard aluminum section powder coated in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed. Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Supply only 4.80mm thick glass ordinary quality plain not exc 0.5 Sqm each pane with including wooden/rubber beading or gasket for aluminium section complete all as specified.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

M&L for broken stone boulder of size exc 63mm but not exc 100mm hand packing at a back of walls over arches etc .and raising (or lowering) to the required height/depth in layers not exc. 15cm thick, watered and rammed complete all as specified and directed

M&L 75 mm thick plain cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) of flooring finishing cement concrete surface even and smooth complete all as specified and as directed

M&L Second class Hard Wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints etc complete all as specified and directed.

S&F for 35 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and fitted to chowkhats complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet,cast or extruded section and fixing bolt of extruded section or cast aluminium alloy complete all as specified and directed.

M&L Preparation of new or untreated painted wood and wooden based surfaces of any description not other wise described over 10 centimeter width or girth and applying Two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L pre polished Machine cut kota stone slab flooring 20-25mm thick jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 complete all as specified and as directed.

M&L pre polished Machine cut kota stone slab 20-25mm thick in riser of steps, thread, skirting, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed or bedding layer of morar 15 mm thick in cement mortar (1:4) complete all as specified and as directed.

Material and labour for screed bed 15 mm thick in CM (1:4) on brick work or concrete surfaces finished even and fair with mixing water proofing compound complete all as specified and directed. Note: WPC shall be measured and paid separately

M & L for APP modified roof treatment over existing roof slab including taking down existing treatment etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sq mtr using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20 degree Celcius (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provided a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/ Sqm as prescribed by manufacturer.

M&L Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces including demolition of existing RCC cover complete all as specified and as directed

Taking down carefully point wiring of any type & pattern (Light/Socket or power) including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings of any type etc and making good disturbed surfaces of walls/ roof etc, complete all as specified and directed.

Taking down complete main switches/DBs with enclosure and its components of any size and capacity etc, complete all as specified and directed.

Taking down of earthed metal clad socket outlet with earthed plug top 20 Amp capacity, sheet metal enclosed and one 20 Amp MCB SPN complete all as specified and directed.

Taking down and refixing of ceiling fan/Exhaust fan, ceiling cable and dismantling blades and shifting to MES store yard during other repair work and its original location including supply and fixing 1.5 sqmm FRLS 3 core flexible multistranded copper conductor cable, 1100V grade from ceiling rose and providing hanging accessories such as rubber reel, cotterpin, nut and bolt including spray painting with 2 coats of synthetic enamel paint servicing and testing for smooth functioning of fan, complete all as specified and directed.

M & L for point wiring complete with proper colour coding, using 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn partly in and including PVC casing caping (minimum 25mm width) fixed on the surfaces of ceiling etc and partly through PVC conduit (minimum 20mm dia) concealed in wall (also including cutting chases in wall and making good the same in CM 1:3 to match with the adjoining surfaces) with all accessories, fittings, PVC junction boxes etc, sunk pressed steel boxes not less than 2 mm thick, 50 mm deep terminal boxes suitable for cover modular plate, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed.

All as per item No 127 above but for 2 pin/ 3 pin socket outlet 5 Amps on independent board.

All as per item No 127 above but wiring 2.5 Sqmm for 3 pin 15 Amps socket multipurpose on independent board complete all as specified and directed

S&F modular type 120W step fan regulator of 2 module complete all as specified and directed.

S&F in repairs decorative recessed type LED light fitting 36 Watt (size '2x2') including driver, including provision of 3 core flexible copper cable 1.5 sqmm conductor wire for connecting from ceiling rose to connector, including making addition/altn to existing false ceiling sheets aluminium frames including fixing arrangement complete all as specified and directed.

Supply and fix 1X18/20 watt LED tube light fitting (including LED), 230 Volt indoor decorative channel housing Surface/wall mounting, with inbuilt electronic control gear , bipin holders, connector block etc complete with all accessories internally pre wired and including connecting lead, three core 1.5 Sqmm, FRLS flexible copper multistranded conductor cable from ceiling rose to tube light fitting complete all as specified and directed.

S&F modular type 6A one way SP switch complete all as specified and directed.

S&F ceiling rose, three terminal, 230 Volts, PVC / Polycarbonate body, complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered type 6 Amps socket independent type conforming to IS: 1293-2005 complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered type 16 Amps socket complete all as specified and directed.

S&F modular type 16 A one way SP switch complete all as specified and directed.

S & F 8 Module factory made screwless, dust proof cover plates having superior finish, rounded corners, solid strength supported by plastic frame behind with flexible wall alignment, horizontal adjustment facility complete all as specified and directed.

All as per ser item No 138 but 3 Module

All as per ser item No 138 but 6 Module

All as per ser item No 138 but 12 Module

S&F MCB DB double door SPN 8 way 240 Volts including connecting up with existing cable/ new cable with lugs complete all as specified and directed.

S & F MCB DB double door SPN 4 way 240 volts including connecting up with existing cable/ new cable with lugs complete all as specified and directed.

Supply and fix in repairs of MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and directed.

Supply and fix in repairs of MCB SPN 240 Volts 40 Amps breaking capacity 10 KA rating complete all as specified and directed.

Supply and fixing earthed metal clad socket outlet with earthed plug top 20 Amp capacity, sheet metal enclosed and 1 No 20 Amp MCB SP all as specified and diredted.

M & L in repairs for sub main wiring complete with Two runs of 4.0 Sqmm PVC insulated, unsheathed, heavy duty, 1100 volt grade multi-stranded copper conductor cable (FRLS), drawn in and including PVC casing caping fixed on the surfaces of walls, RCC slab/ ceiling/columns / beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 4.0 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continuous earth wire connected to common earth dolly and mains, complete all as specified and directed. Note: Three runs of 4.0 Sqmm PVC cable and one run of PVC Casing Caping will be measured as 'one unit' length.

M & L in repairs for sub main wiring complete with Two runs of 6.0 Sqmm PVC insulated, unsheathed, heavy duty, 1100 volt grade multi-stranded copper conductor cable (FRLS), drawn in and including PVC casing caping fixed on the surfaces of walls, RCC slab/ ceiling/columns / beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 6.0 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continuous earth wire connected to common earth dolly and mains, complete all as specified and directed. Note: Three runs of 6.0 Sqmm PVC cable and one run of PVC Casing Caping will be measured as 'one unit' length.

S&F Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed.

Supply and fix switch socket combination 2 in 1, 5 Amp flush type complete all as specified and directed.

S&F ceiling rose, three terminal, 230 Volts, PVC / Polycarbonate body, complete all as specified and directed.

Supply and fixing energy efficient BEE five star rated ceiling fan, 1200mm sweep and connecting up including provision of three core flexible copper wire of size 1.5 sqmm from ceiling rose to ceiling fan complete in all respect all as specified and directed. Make Crompton /Orient/ Bajaj/Havells.

M&L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection all as specified and as directed by EIC. Note : Sand after punning down will be measured

Supply and laying precast concrete cable cover class LV ISI Marked, type-I, flat size 250mm x 150mm x 40mm laid in trenches all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core including cable lugs of suitable size complete all as specified and directed. Note : A sum of Rs 10,380.00 towards sch of credit shall be deducted to arrive the contract sum.

Parmatma Enterprises

GAJANAN SALES CORPORATION