Construction of proposed new 6 bays Bus stand at existing campus of Bus stand at Barwala in Hisar Distt.(Pdg. Balance Street light only)

Amount

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA [Through Rate]

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]

[23.27.1]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 1. M.S. pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in 1:2:4 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level , having a base of size 900 mm x 600 mm x 250 mm below ground level. 0 0 [Through Rate]

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]

[24.1.13]EARTHING AND LIGHTENING ARRESTOR 13. Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. [Through Rate]

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]

[24.1.6]EARTHING AND LIGHTENING ARRESTOR 6. Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required. [Through Rate]

[24.13.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]

[24.13.30]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 30. 25 Sq mm 3.5 core (Arm.) [Through Rate]

[24.2.7.2]LT CABLE 7.2. Supply and erection of suitable compression type brass cable glands for underground Cable :- 10 sqmm to 16 sqmm Cable 2 to 4 Core [Through Rate]

[24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core [Through Rate]

[24.2.8.4]LT CABLE 8.4. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm [Through Rate]

[24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm [Through Rate]

[24.5.1.1]MISCELLANEOUS ITEMS 1.1. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 1.5 sqmm [Through Rate]

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

[24.8.5]RCC FOUNDATIONS FOR OCTAGONAL POLES 5. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 7m high pole [Through Rate]

Supply and Erection of 7 mtr Decorative Poles with DOUBLE arm and Light 7 Mtr. Decorative pole made of Mild Steel with Pole bottom base section will be 200x200x2000mm, 4mm Thk. column with predesigned CNC Laser Cut pattern made with in-house Rotatory Laser cutting machine for sophisticated illumination with inbuilt 20W light, Next Section will be double pipe of size 60x3mm to work together to form unique design with mid-section of illuminated in warm white laser cut design with golden color and predesign CNC Laser Cut pattern made with in-house Laser cutting machine for sophisticated illumination in Warm white 60W, DOUBLE arm bracket carrying street light MF SL LED 300D(i) 72w at each arm. This LED IP-65 street light type fixture is made of die cast aluminium housing fitted with Polycarbonate lens. The base plate of pole shall be size of 400x400x12mm.The pole will have 3 side laser cut design and the back would have Provision for inside termination box (Space) for 4way connector and 1 nos 6 AMPS MCB for local isolation. The pole is primarily coated with primer and top coated with UV stabilized Polyutharene Paint and cured. Pole light is complete in all aspects with all accessories. Make:- Havells/Keselec/Mayfair/Bajaj.(Exclusive GST).

Supply and Erection of 7 mtr Decorative Poles with SINGLE arm and Light 7 Mtr. Decorative pole made of Mild Steel with Pole bottom base section will be 200x200x2000mm, 4mm Thk. column with predesigned CNC Laser Cut pattern made with in-house Rotatory Laser cutting machine for sophisticated illumination with inbuilt 20W light, Next Section will be double pipe of size 60x3mm to work together to form unique design with mid-section of illuminated in warm white laser cut design with golden color and predesign CNC Laser Cut pattern made with in-house Laser cutting machine for sophisticated illumination in Warm white 60W, SINGLE arm bracket carrying street light MF SL LED 300D(i) 72w at each arm. This LED IP-65 street light type fixture is made of die cast aluminium housing fitted with Polycarbonate lens. The base plate of pole shall be size of 400x400x12mm.The pole will have 3 side laser cut design and the back would have Provision for inside termination box (Space) for 4way connector and 1 nos 6 AMPS MCB for local isolation. The pole is primarily coated with primer and top coated with UV stabilized Polyutharene Paint and cured. Pole light is complete in all aspects with all accessoriesMake:- Havells/Keselec/Mayfair/Bajaj.(Exclusive GST).

S/I/T/C of time light distribution board (Astronomical) 65 amp 3 pole / 230 Volts with digital time switch having suitable size of 1 no. 63 amp TPN MCB, 1 no. 65 amp contactor, 1 HRC fuse , 1 No. Rotray Switch, 1 No. 16 amp fuse base, 1 No. Timer switch and 1 Indicator having IP 52/56 Degree protection all items should be of same make / manufacturer including pedestal, including making connection and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in Charge of the work. (Make:- Havell`s/ L andT). (Rates are excluding GST)

INDIAN SECURITY AND FIRE SAFETY (BID ID -1396796)