Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.5 CrAdmitted-Finance | ₹3.5 Cr | L1 | Admitted-Finance |
| 2 | Rejected-Technical | - | - | Rejected-Technical rejected |
| Sl No | Description | Qty | Unit | FAVOURITE ELECTRICALS L1 |
|---|---|---|---|---|
| 1.00 | Sub Head 'A' - Machinery
AIR COOLED SCREW HEAT PUMP (REVERSIBLE TYPE) For Space Cooling and Heating
Supply, installation, testing and commissioning of Screw type Heat Pump unit as per the technical specification annexured as annexure "B" | 3 | No | 1,04,30,775 ₹3,12,92,325 Lowest |
| 2.00Water Pumps Set Supply, Installation, Testing and Commissioning of End Suction Back pull-out centrifugal pumps complete with motor, base frame, vibration isolators, drain valves and other accessories. Pumps shall have mechanical seal and Bronze Impeller. The pump shall be fitted with motor suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The job includes cost of providing, welding, and fitting of Flanges, Reducers, nipples, Nut Bolts, thermal insulation and cladding for hot water pumps as well as M.S base frame for mounting pump and motor along with VI pads. Pumps shall be complete as per specifications and shall have operating parameters as given below: | ||||
| 2.10 | Chilled Water Primary Pumps Set
Water flow rate : 480 USGPM for Space heating / cooling (1817 LPM)
Head : 40ft
Motor HP : 7.5 HP (suggested)
RPM : 1450 | 3 | Set | 1,13,457 ₹3,40,371 Lowest |
| 2.20 | Secondary Hot water pumps (with VFD & Microprocessor Panel, sensor, transformer, controller, star Delta Starters etc.) for Space heating / cooling
Water flow rate : 520 USGPM for Space cooling (1968 LPM)
Head : 80ft
Motor HP : 20 HP (suggested)
RPM : 1450 | 3 | Set | 2,76,463 ₹8,29,389 Lowest |
| 3.00Sub Head 'B' - CHILLED WATER PIPES AND VALVES Supplying, laying/ fixing, testing and commissioning of following nominal sizes of Hot / chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. | ||||
| 3.10 | 300mm NB.(75mm insulation) | 42 | RMT | 8,994 ₹3,77,748 Lowest |
| 3.20 | 250mm NB.(75mm insulation) | 120 | RMT | 7,673 ₹9,20,760 Lowest |
| 3.30 | 150mm NB(75mm insulation) | 80 | RMT | 4,403 ₹3,52,240 Lowest |
| 3.40 | 25mm NB (50mm insulation) | 120 | RMT | 1,263 ₹1,51,560 Lowest |
| 4.00INUSLATED VALVE Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. | ||||
Tender Value
₹3.8 Cr
EMD Value
₹7.7 L
Closing Date
8 Sept 2025, 11:00 amClosed
Executive Engineer MHD SKIMS/JVC
SKIMS Soura
HVAC System(High Side) for new 250 bedded IPD Block at SKIMS Medical College and Hospital , Bemina Srinagar
2025_PWDJK_285650_1
MHD/SKIMS/JVC/42 0F 2025-26 DATED.27.08.2025
Open Tender
Machineries/ Mechanical Engg Items
Item Rate
180 days
SKIMS Bemina
Please refer Tender documents.
9 documents required · 9 mandatory
₹2,500
Executive Engineer MHD SKIMS/JVC
₹7.7 L
13 Oct 2025
28 Aug 2025
8 Sept 2025
28 Aug 2025
8 Sept 2025
28 Aug 2025
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Sub Head 'A' - Machinery
AIR COOLED SCREW HEAT PUMP (REVERSIBLE TYPE) For Space Cooling and Heating
Supply, installation, testing and commissioning of Screw type Heat Pump unit as per the technical specification annexured as annexure "B" | 3 | No | - | - |
| 2Water Pumps Set Supply, Installation, Testing and Commissioning of End Suction Back pull-out centrifugal pumps complete with motor, base frame, vibration isolators, drain valves and other accessories. Pumps shall have mechanical seal and Bronze Impeller. The pump shall be fitted with motor suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The job includes cost of providing, welding, and fitting of Flanges, Reducers, nipples, Nut Bolts, thermal insulation and cladding for hot water pumps as well as M.S base frame for mounting pump and motor along with VI pads. Pumps shall be complete as per specifications and shall have operating parameters as given below: | |||||
| 2.1 | Chilled Water Primary Pumps Set
Water flow rate : 480 USGPM for Space heating / cooling (1817 LPM)
Head : 40ft
Motor HP : 7.5 HP (suggested)
RPM : 1450 | 3 | Set | - | - |
| 2.2 | Secondary Hot water pumps (with VFD & Microprocessor Panel, sensor, transformer, controller, star Delta Starters etc.) for Space heating / cooling
Water flow rate : 520 USGPM for Space cooling (1968 LPM)
Head : 80ft
Motor HP : 20 HP (suggested)
RPM : 1450 | 3 | Set | - | - |
| 3Sub Head 'B' - CHILLED WATER PIPES AND VALVES Supplying, laying/ fixing, testing and commissioning of following nominal sizes of Hot / chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. | |||||
| 3.1 | 300mm NB.(75mm insulation) | 42 | RMT | - | - |
| 3.2 | 250mm NB.(75mm insulation) | 120 | RMT | - | - |
| 3.3 | 150mm NB(75mm insulation) | 80 | RMT | - | - |
| 3.4 | 25mm NB (50mm insulation) | 120 | RMT | - | - |
| 4INUSLATED VALVE Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. | |||||
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.03 MB
BOQ_888970.xls
BOQ • 0.29 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .