ADDN/ALTN AND SPECIAL REPAIR TO BLDG NO 49 OF 131 SATA REGT AND EXECUTION OF CERTAIN MINOR WORKS AT NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in Cement mortar comlete all as specfied and directed.

M&L for Keyed pointing to random or polygonal rubble, uncoursed with CM 1:3 or brought upto course complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on other than fair faces of stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @3% by weight of cement on fair faces of brick work or concrete surfaces, finished even and smooth complete all as specified and directed (WPC measured and paid separately) .

M&L for 10mm thick rendering in cement mortar in CM (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rough cast plaster over 10mm thick cement plaster in cement mortar 1:4 on stone / brick masonary wall surfaces complete all as specified and directed.

M&L for new plastered surface of wall and applying two coat of distemper oil emulsion distemper over coat of primer over 1mm thick average thick wall care putty, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparation of surfaces and applying two coats of weather proof acrylic emuslion paint over a coat of 1mm thick wall care putty & including a coat of emulsion wall primer all as per manufacture's instructions & as directed by Engr -in-Charge. Make :- Asian / Apex / Berger (Wheather coat All Guard).

M&L for complete removal of existing treatment of old plastered surface of wall and applying two coat of distemper oil emulsion / oil bound distemper over coat of primer over 1mm thick average thick wall care putty, complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in ground floors and pavings n. exc 15cm thickness (below or above ground level).

M&L for machine cut Kota stone slab flooring 20-25mm thick over 15mm thick screed bed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing complete all as spd & directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edges of stone slabs one edge, complete all as spcified and directed.

S&F in repair stainless steel sinks with draining board made of 1mm thick sheet with over all size 915mm x 460mm and bowl size 410mmx330x160mm for kitchen or laboratory with pluge washers and waste, including bedding in cement mortar on to dwarf walls or including fixing centilever bracket and connecting uinon to waste pipe complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

M&L Glazed ceramic coloured tiles 7 to 8 mm thick in vertical surfaces area of each tile of exc 0.11 Sqm and but not exc. 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick plastering in cement mortar 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade, 10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 sqm, in vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed plaster 10mm thick in CM 1:4 complete all as specified and directed.

M&L 25 mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregate as in sub base of floors complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for fly ash brick work old size bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for fly ash brick work with old size bricks staright or curved on plan to any radius in half brick walls, built in CM 1:4 complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3 complete all as specified and directed.

S & F in repair vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

Taking down old unserviceable WHB and S&F wash hand basin vitreous china white / ivory colour flat size 600 x 350mm ,oval type fixed including 40 mm bore waste coupling, waste pipe complete all as specified and directed

Supply and fix in repair vitreous china urinal half stall type white with grating and union for discharge pipe including waste pipe, fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs and 60 mm long brass screws pointing around urinal back in cement, excluding flushing cistern, flush pipe and waste pipe complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S & F PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F in repair tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S&F in repairs Chromium plated Angle cock 15 mm dia screwed down light pressure screwed both ends for iron pipe or for union complete all as spd & directed

S&F in repairs Chromium plated bib taps, fancy type with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S&F two way bib cock of 15mm bore, cast copper alloy, chromium plated, complete all as specified and directed by Engr-in-Charge

S&F Health faucet, cast copper alloy, chromium plated complete all as specified and directed by Engr-in-Charge

S&F Jet flush including plate & connection pipe complete all as specified and directed.

S&F Two way angle cock of 15 mm bore, cast copper alloy, chromium plated, complete all as specified and directed by Engr-in-Charge

S&F for chromium plated centre hole basin mixer w/o pop up of 15mm bore complete all as specified and directed by Engineer-in-Charge (Cat No- 8750 of Prayag / equivqlent from specified make as approved by GE)

S&F CP wal mixer 3-in-1 ( with provn for OHS & hand shower) screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed Make - Cat No- 9380 of Prayag or their equivqlent approved by GE

S&F Corner Glass shelf with bracket as per sample approved by the GE.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item No. 43.00 above but 20 mm bore.

All as per srl item 43.00 above but 25 mm bore.

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item No. 46.00 above but 20 mm bore.

All as per srl item No. 46.00 above but 25 mm bore.

M&L PVC Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing complete all as specified and directed.

S & F Factory Made Solid PVC moulded door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter (Two/Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S & F in repairs window ECO 4000 of double rebate epenable / fixed window made of galvanised steel colour coated / powder coated ( base steel a per IS 513 of D Quality galvanised as per IS 277 with zinc of 120 gms/sqm) with total thickness of coating 0.58 microns thick coated with alkyed backer 5-7 micron thick or powder coated with pure polyster upto 50-60 micro thick . Outer frame section 72x55 mm , centre mullion section , 72x50 mm , shutter section 47x20 mm flymesh section 40x20 mm the fixed glass beading section 12x12 mm , outer frame and mulions shall consist rebate for glazed shutter , fly mesh and 20 provision for gaurd bars/ grills the section cut to length mitre joined with corner bracket centre mulions fixed with mulions cap , stay , handle , latch , 2 Nos of heavy duty stainless steel pivot with hinges per shutter and panelled with 5 mm thick plain float glass and S S mesh for fly mesh shutter ( 304 grade) fitted using EPDM (Enthy propyelene diamine monomer ) gasket including fixing fixing windows in the concrete / masonary wall by means of shelf expanding screw including 10 mm square bars welded to 6x12 mmlat at a disance 150 mm C/C (Pitch) etc complete as per direction of Engr-In-Charge. Make - NCL Alltek and seccolar Ltd r equivalent as approved by GE.

S&F rolled mild steel work angle iron as in door frame (Chowkhats) of frame confirming to Fe-290 or Fe-165 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

M&L for 18/19mm thick prelaminated particle board exterior grade pelaminated both side with decorative choice fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

S & F 75mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Dismantling existing RCC/PVC water tank and Supply and fixing 500 Litre capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top), white colour, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I complete al as spd & directed.

Dismantling existing RCC/PVC water tank and Supply and fixing 1000 Litre capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), white colour, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I complete al as spd & directed.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm)

S&F gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as spd & directed.

M&L 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank/ manhole cover complete all as specified and directed.

Taking down existing unservicable treatment of any description including cement plaster/conctrete any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as specified and directed.

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/ Sqm applied with bonding material using blown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with clamps complete all as specified and as directed by the Engineer-in-Charge

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F for 110mm bore PVC (SWR) junction single (Single T) equal or unequal with oval access door, complete all as specified

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 75mm bore PVC (SWR) vent cowl, complete all as specified

Supply only stack clamp out of 50mm by 3mm flat iron and 16 mm dia round iron stays fixed to pipe of bore 110mm complete all as specified.

Dismantling loose /disintegrated portion of RCC Chajjas, bend shelves,ceiling, beams balconies and similar work at any position or any height and dobbing out with PCC 1:1.5:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished required shape including applying anti corrosive paint on exposed surfaces and provision of necessary supporting form work and including 10mm thick plastering in CM 1:4, finished fair and even, complete all as specified and directed.

Providing & fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm,including dismantling of existing ceiliong any type, all complete at all heights as per direction of Engineer-in-charge.

Excavation in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil complete al as spd & directed.

Surface dressing not exc 15cm deep in soft/loose soil.

Excavationg in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in any type of soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete.

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

Excavation over areas depth exc 1.5m and not exc 3m and getting out in soft/loose soil all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate in foundations as in fixing vertical tubular post etc, complete all as directed.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type, interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment including necessary welding etc. conforming to Grade E-165 (Fe 290) all as specified and as directed.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook, complete all as specified & directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

M&L for flyas brick work with old size bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified.

M&L for 100 mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in hardstanding, top surface finished fair & even (PCC shall be laid in alternate bays in panels of size not exc 2m x 2m with 6mm wide and 100mm deep joints filled with bitumen mastic 1:1., complete, all as specified and as directed.

M&L for cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3, not exc. half brick thick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)

S&F rolled mild steel as in angle sections, fixed independently, with or without connecting plates or welding with existing steel or iron surfaces, etc. and similar work conforming to Grade E-165 (Fe 290) including necessary cutting, welding etc and fixing in position complete all as specified & directed.

S&F stainless steel Kitchen plate rack of overall minimum size 914mm x 610 mm and 254 mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed.Note : Weight of rack shall not be less than 6.00 Kg. . Make: Pryag Cat No. P-336 or equivalent from other specified make.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 (ISI marked), drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick( Make - Hylem/Anchor) ISI Marked, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point controlled by one, one way switch.

One Ceiling fan/wall fan/exhaust fan controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board.

All as per item No. 116.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 1.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed. Make : Cona / SSK / Havells

Taking down existing exhaust fan & wall mounted fan and re-use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make :- Havells/Bajaj/ Usha

S&F of ventillation fan 250mm sweep non metallic white colour including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make:- Havells/Bajaj/ Usha

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired complete all as specified and directed. Make :- Bajaj/Havells/Crompton/Philips

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed.Make :- Bajaj/Havells/Crompton/Khaitan

Supply and fixing wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic body suitable for B22 Base complete all as specified and directed by Engr-in-Charge. Make: Havells , Model- LHFOECE1TZ1O014, HSN Code: 9405 or equivalent model of Mepro/Philips

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make :- Bajaj/Havells/Crompton/Philips

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed. Make :- Havells Cat Part No LHEOAP7UZ6W010 or equivalent model of Philips/Crompton

Supply and fixing and testing energy saving street light luminaire 25 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make :- Bajaj/Havells/Crompton/Philips

Supply and fixing recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed. Make Crompton/Havells/Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

S&F water heater storage type,electric, capacity 25 litres, BEE 5 star rated, 240 volts, input 2000 KW, PUF insulated fitted with stainless inner container and cooper coil of BEE 5 star rating models, max working head of water 25 Ltrs, fixed to wall with suitable MS tower/anchor bolts,Inlet/outlet pipes incl PVC connections grouted to wall, Make:Havells/Usha/Bajaj.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable.

M& L for TV Socket including PVC conduit and axial cable wire.Make : Cona / SSK / Havells

M& L for Telephone socket including PVC conduit and telephone wire.Make : Cona / SSK / Havells

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed. Make :- Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Taking down and Supply and fixing of Change over Three Pole Neutral AC 63 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed. Make: Havells Cat No IHKDTW4063 or equivalent.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make :- Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make :- Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make :- : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .complete all as specified and directed. Note. The unit rate includes for protection pipe and GI wire 4.00mm from top of earth plate up to 7.5 meter above ground level.

Shree Sai Ram Enterprises

Abdul Gani Abdul Sattar

kirtiman traders

SHREE BALAJI TRADING CORPORATION

M/s S. K. Construction Co.

M/s Jai Jinendra Constructions

M/S Nexus Projects

M/S AL ASMA ENTERPRISES

PD GUPTA AND COMPANY