Construction of Temple Peer Gouns Pak Giyarwinwala, at Changer Makrer, Dev. Block Bangana, Distt. Una H.P. (SH- Balance work for the completion of basement l and basement ll )

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in Excavation in foundation trenches etc. in earth work in all kinds of classification of soil such as pick work, jumper work, pick jumper work, blasting work in jumper blasting work soft and hard blasting and doing work in saturated soil, including chiseling or wedging out rock where blasting is prohibited, or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads, as directed by Engineer-in-Charge and then returning the stacked soil in 15cm (fifteen centimeters) layers when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials within all leads and lifts. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto all lead and lifts, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:5:10 (One cement is to five sand isto ten graded crushed/ broken stone aggregate 40mm (Forty millimetre) nominal size and curing complete excluding cost of form work in retaining walls, return walls, walls (any thickness) including attached plasters, columns, piers, abutments, pillars, posts, struts, bittresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, complete as per HPPWD specification, as directed by the Engineer-in-Charge, and carriage of materials within all leads and lifts and other incidental charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (1cement :4sand :8 graded stone aggregate 40mm. nominal size) with 15 % plum and curing complete excluding cost of form work in retaining walls/ Breast walls, the size of plums shall usually be 150mm. to 300mm. as per H.P.P.W.D. Specification as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering, strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partition and the like including attached pillasters, buttresses, plinth and string courses and the like, up to all floor level, complete as per HPPWD specification and as directed by Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

6 mm thick cement plaster to ceiling in cement mortor 1:3 ( 1 cement : 3 sand)up to all floor complete including carriage of material with all leads, lifts and other incidentals . The rates includes Ocroi , royality, Malakana, Sate tax, Toll tax,CGST,SGST or any other taxes imposed by the Govt.

15 mm thick cement plaster on fair side of brick / concrete/ stone masonary walls for interior plastering internal rounded anges not exceeding 80 mm grith and finished even and smooth with cement mortor 1 : 5 ( 1 cement : 5 sand ) above plinth level including carriage of materials within all leads, lifts and other incidentals as p[er specifications approved drawings , design and directed by the Engineer in Charge . the rate includes Ocroi, Royality, Malakana, sate tax , CGST , SGST or any other taxes imposed by the Govt.

20 mm thick cement plaster on rough side of brick / concrete/ stone masonary walls for interior plastering internal rounded anges not exceeding 80 mm grith and finished even and smooth with cement mortor 1 : 5 ( 1 cement : 5 sand ) above plinth level including carriage of materials within all leads, lifts and other incidentals as p[er specifications approved drawings , design and directed by the Engineer in Charge . the rate includes Ocroi, Royality, Malakana, sate tax , CGST , SGST or any other taxes imposed by the Govt.

P/L machnically and vibrated mixed cement concete 1:2;4 ( 1 cement :2 sand : 4 graded stone agg 20 mm thick ) Including carriage of materisls with all leads. Lifts and other incidentals . The rates includes octroi royality, malkana, sale tax, toll tax , CGST,SGST or any other taxes imposed by the Govt.

Provoding and fixing powder coated aluminium work for door,window ,ventilators and parttions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868.(Minimum anodic coating of grade AC 15 ) fixed with rawplugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junction,at top,bottom sides with required PVC/Neoprene felt etc.Aluminium sections shall be smooth,rustfree,straight,mitred and jointed mechanically where ever required including cleat angle,aluminium,snap beading for glazing /panelling C.P brass/Stainless steel screws .All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.