Development of Smart Parking at Vikas Nagar in ward No 29 under Shimla Smart City Mission

Amount

Cutting in earth work in all kinds of soil including spade work, pick work, jumper work and blasting work and disposal of excavated earth up to all leads and lifts as directed by Engineer-in-Charge. (Disposal of earth/muck in MC dumping site at Bharyal free of cost, transportation charges will be paid extra)

Excavation in earth work in all kinds of earth work including spade work, pick work, jumper work, B/work chiseling wedging out of rock etc. up to all lifts in earth work including dressing of sides and bed and disposing of excavated earth to be leveled and neatly dressed as directed by the Engineer-in-charge. (Disposal of earth/muck in MC dumping site at Bharyal free of cost, transportation charges will be paid extra)

Excavation in earth work and filling in 15 cm. layers in foundation and plinths including ramming, watering and consolidating upto a lead of 20 metres and lift upto a 1.5 metres.

Disposal of materials (earth work) by mechanical transport including loading and unloading and stacking upto 10 km (disposal of earth at approved MC dumping site)

Providing from work with steel plates 3.15 mm thick welded with angle iron in frame 30*30*5mm so as to give a fair finish including centring , shuttering and propping etc.with wooden battens height of propping and centring below supporting floor to ceiling upto all heights and removal of the same for insitu -reinforced concreate & plain concreate work in:-. Foundation , footing basis of coulmn etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs ,landings and the like Floor etc. up to 200 mm in thickness

Coulmn , pillars , post and struts:-

Beams , cantilever , grinders and lintels:- Sides and soffits of beams beam haunching cantilevers , brssumers and lintels not exceeding 1 metre in depth in all heights from floor

Vertical surfaces such as walls partition and the like including attached pilasters buttresses plinth and string courses and the like.

Stair case with sloping or stepped soffits including risers & stringers excluding landing.

Providing and laying cement concrete 1:4:8 (1 cement: 4 sand: 8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth with in all leads , lifts of materials and other incidentals.

Providing and laying cement concrete 1:1:2 (1 cement : 1 sand :2 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement in reinforced concrete work in :Foundation And Plinth

Walls (any thickness but not exceeding 0.1 m thickness) including attached pilasters, buttersses,plinth and string concrete etc. From the top of foundation level up to 2 level.

Suspended floors roofs, landing and shelves and their supports , balconies, beams, griders, bressumers and cantilivers upto floor two level.

Lintels, beams girders bressumers and cantilevers up to floor two level :

Column, pillars, posts and struts upto floor two level :

Stair cases (except spiral cases) excluding landing,but preparing of the the surface & finishing of nosing upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete up to floor two level:

Steel work welded in built up section , trusees and framed work including cutting , hoisting, fixing in postion and applying a priming coat of red lead paint inculding carriage of materials with in all leads and lifts.

Brick work using common burnt clay building bricks in in Superstructure above plinth level upto floor two level :Cement mortar 1:6 (1 cement : 6 sand)Second Class Bricks

Cement concrete flooring 1:2:4 laid in one layer finished with a floting coat of neat cement including carriage of materials withinn all leads and lifts.40 mm thick

6mm Cement plaster to ceiling In Cement mortar 1:3(1 Cement:3 Sand)

15mm thick cement plasters in single coat on fair side of brick/concrete /stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in grith and finished even and smooth with cement morter 1:6 (1 cement:6 sand).

15mm thick cement plasters in single coat on rough side of brick/concrete /stone walls for exterior plastering up to all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in grith and finished even and smooth in cement morter 1:6 (1 cement:6 sand).

Distempering (Two Coat) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface on all floor to give an even shade over and including priming coat of whiting after thoroughly brushing the surface free from morter dropping and other foreign material including preparing the surface even and sand papered smooth including carriage of materials within all leads and lifts:-

Applying white cement based wall care putty over plaster surface after thoroughly brushing the surface free from morter drops , dust , loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. (a) 150mm dia pipes

Stone filling behind retaining Wall.

Providing and fixing 0.6mm thick prepaintd steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of ployster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

VENTILATION Design, manufacture, supply, installation, testing and commissioning of wall mounted tube axial exhaust air fan with motor of following capacity complete with starter panel, wire mesh etc. along with other accessories, as required. (For Pump Room & DG Room at Gr & 4th Floor) Capacity: 2,000 CMH, 10 mm WC

Design, manufacture, supply, installation, testing and commissioning of wall mounted tube axial exhaust air fan with motor of following capacity complete with starter panel, wire mesh etc. along with other accessories, as required. (For Electrical Room 6th Floor) Capacity: 1,500 CMH, 10 mm WC

Design, manufacture, supply, installation, testing and commissioning of wall mounted propeller type exhaust air fan with motor of following capacity complete with starter panel & other accessories, as required. (For Toilets at 6th Floor) Capacity: 750 CMH, Free air delivery

Design, manufacture, supply, installation, testing and commissioning of extruded aluminium powder coated fixed blade type exhaust air grilles, as required.

Internal Plumbing Details SANITARY FIXTURE AND CP FITTINGS Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing C.P brass toilet paper holder

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of require shapoe & size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

INTERNAL DRAINAGE (BUILDING) Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand). Stone ware spout

WATER-SUPPLY (BUILDING) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 15 mm nominal outer dia. Pipes.

20 mm nominal outer dia.Pipes.

25 mm nominal outer dia. Pipes.

32 mm nominal outer dia. Pipes.

40 mm nominal outer dia.Pipes.

50 mm nominal outer dia.Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia.Pipes.

50 mm nominal outer dia.Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.(for rising main from UGT to terrace) 25 mm dia nominal bore

32 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 25 mm dia nominal bore

32 mm dia nominal bore

Fire Water Pumping System Supply, Installation, testing and commissioning (SITC) of Electric motor driven Horizontal Centrifugal End Suction Type Main Pump having flow 137m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set.(IS Approved)

Supply, Installation, testing and commissioning (SITC) of Diesel Engine driven Horizontal Centrifugal End SuctionType Standby Pump having flow 137 m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set. Including fuel tank (fabricated from 3mm MS sheet, painted with two coats of synthetic enamel paint over a coat of primer) of capacity adequate to sustain pump operation for 8 hours continuous working. The tank shall be fitted with Magnetic oil level indicator, MH with cover, drain valve, air vent including structural supports (painted with approved shade), 2 Nos. x 12 volt battery WITH CHARGER, heat exchanger with necessary piping connections & fittings, flexible coupling, coupling guard & exhaust pipe connection complete as required. Cost shall be inclusive of providing & fixing of fuel tank of required capacity etc. all(IS Approved)

Supply, Installation, testing and commissioning (SITC) of Electric motor driven Horizontal Centrifugal End Suction Type Jockey Pump having flow 10.8 m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set.(IS Approved)

Supply, Installation, testing and commissioning (SITC) of Piping complete confirming to IS: 1239 and IS: 3589 (6 mm thick) Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing in trench, wall, Ceiling by using suitable structural supports etc.(UL/FM approved grooved fittings) 250 NB

Supply, Installation, testing and commissioning (SITC) of Valves Gate Valve 250 NB

Non return valve 250 NB

150 mm dia

Supply, Installation, testing and commissioning (SITC) of Air Vessel Air Vessel of 300 mm dia.& Height 1.2 mtrs. Heavy class G.I. pipes as per IS 3589 complete with nozzles for inlet , outlet, air release valve , pressure switch panel and drain , etc. complete

Supply & installation Auto Air vent for Air Vessel, suitable for pressure not less than 15 Kg/Sq.cm.

Supply, Installation, testing and fixing of dial type (100 mm) pressure gauge with isolation globle valve suitable with ‘U’ tube for working pressure of 12 Kg/cm2 having calibration of 0-16 Kg/cm2. Cost shall be inclusive of providing any short pieces, nipples, elbows etc as required.

Supply, Installation, testing and commissioning (SITC) of Pressure switches. The Pressure Switch shall be diaphragm type. The housing shall be die cast aluminum, with SS 316 movement, pressure element and socket. The Switch shall be suitable for consistent and repeated operations without change in values. It shall be provided with IP: 65 enclosures. Range of pressure switch shall be 0-16 kg/cm2 and shall be provided with isolation ball valve.

Supplying and installing fire brigade Inlet Header, G.I. 'C' class pipe as 1 Mtr high, having 4 Nos. of 63 mm gun metal instantaneous inlet with inbuilt spring type NRV, including aluminium chain & PVC cap. And Sluice valve of suitable size for supplying water, etc as complete to operate.

Supplying and installing fire water draw off connection 150mm dia G.I. "C" class pipe, from Water Tank to outside approachable location. Including the flanges to be provided for the easy maintenance with Isolation Sluice valve for system, etc as complete to operate

Supply, Installation and erection of Structural Steel for supports including anchor fastners, ISMB Channels, angles, painting of structures.

Over Head Fire Water Tank Pumping System Supply, Installation, testing and commissioning (SITC) of Electric motor driven Horizontal Centrifugal Monoblock Type Booster Pump having flow 900 LPM & 35 WMC head along with all accessories required for the pump set.

Supply, Installation, testing and commissioning (SITC) of Piping complete confirming to IS: 1239 and IS: 3589 Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing on RCC pedestal supports and suitable structural supports etc. 150 NB

Supply, Installation, testing and commissioning (SITC) of VALVES Gate Valve 150 NB

Non return valve 150 NB

Y type strainer ( Mesh Size 40 ) 150 NB

Supply & Installation of Pressure indicators complete with isolation valve, tubing etc.

External Fire Hydrant System Supply, Installation, testing and commissioning (SITC) of Piping complete confirming to IS: 1239 and IS: 3589 Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing in RCC trench by using suitable supports. 200 NB

Supply, Installation, testing and commissioning (SITC) of Underground piping complete confirming to IS: 1239 and IS: 3589 Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing on earth by using suitable supports,Wrapping and coating for underground piping as per IS: 10221:1982. etc. 200 NB

Supply and installtion of Gate Valves 200 NB

Supply and erection of Valve chamber in masonary / RCC construction with M.S.cover

Excavation & Back Filling for the following items Soft Soil

Hard Soil

Soft Rock

Hard Rock

Hydrant Accessories Supply, Installation, testing and commissioning (SITC) of external Hydrants confirming to IS 5290 (Type “A”) Hydrant valve shall have single outlet having 80 NB flanged inlet. Outlet shall be oblique female instantaneous type coupling having spring loaded lugs; internal parts shall be of copper or gunmetal. A cap with chain shall be provided on the outlet of the valve. Stand post of 80 NB of suitable length

Designing, Supply and installation Orifice plate made out of stainless stand plate (SS 304, 6mm thick) for following size of pipe to reduce pressure upto 7 Kg/sqcm complete in all respects. 80 mm NB

Supply & installation controlled percolation fire hose pipe (as per IS:8423) of 63 mm dia and 15 meter length rated for brust pressure of 35.7 Kg/sqcm. The hose shall be tested for flame resistance test in accordance to IS:8423. Hose shall be complete with ISI marked gun metal male & female coupling (IS:903) bound & riveted to hose pipe with copper rivets & 1.5 mm copper wire (Location : External fire hydrant).

Supply & installation of 63 mm dia instantaneous pattern, short gun metal branch pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling complete as required.

Supply & installation Weather proof standard fire hose cabinet having single or double opening glazed (3.0 mm thick glass) shutter including necessary locking arrangement by allan key, stove enamelled Fire red finish (as per IS : 5, shade no. 536) with " Fire Hose" marked on front, suitable for housing 2 nos. Hose pipe, 1 No. branch pipe .

Internal Fire Hydrant System - Wet Riser Supply, Installation, testing and commissioning (SITC) of Piping complete confirming to IS: 1239 and IS: 3589 Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing in RCC Trench, Ceiling, Duct (fire shaft) by using suitable supports etc. 150 NB

Supply, Installation, testing and commissioning (SITC) of Pipes confirming to IS:1239 Pt 1 & IS:3589 Heavy grade GALVANISED , including cutting, threading, welding etc. and providing all fittings e.g.. elbows, reducers, clamps, UL listed hangers and pipe supports, fastners , flanges, gaskets, nuts, bolts and washers etc. It shall be including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade. It shall be including cutting holes and chases in brick or rcc walls/slabs and making good the same etc. complete in all respect as required.150 NB

Excavation & Back Filling for the following items Soft Soil

Hard Soil

Soft Rock

Hard Rock

Supply, Installation, testing and commissioning (SITC) of Gate Valve 200 NB

Supply and erection of Valve chamber in masonary / RCC construction with M.S.cover

HYDRANT ACCESSORIES Supply, Installation, testing and commissioning (SITC) of Internal Hydrants confirming to IS 5290. Hydrant valve shall have twin outlet having 100 NB flanged inlet. Outlet shall be oblique female instantaneous type coupling having spring loaded lugs; internal parts shall be of copper or gunmetal. A cap with chain shall be provided on the outlet of the valve.

Designing, Supply and installation Orifice plate made out of stainless stand plate (SS 304, 6mm thick) for following size of pipe to reduce pressure upto 7 Kg/sqcm complete in all respects. 100 MM NB

Supply & installation controlled percolation fire hose pipe (as per IS:8423) of 63 mm dia and 15 meter length rated for brust pressure of 35.7 Kg/sqcm. The hose shall be tested for flame resistance test in accordance to IS:8423. Hose shall be complete with ISI marked gun metal male & female coupling (IS:903) bound & riveted to hose pipe with copper rivets & 1.5 mm copper wire (Location : External fire hydrant).

Supply & installation of 63 mm dia instantaneous pattern, short gun metal branch pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling complete as required.

Supply & installation Weather proof standard fire hose cabinet having single or double opening glazed (3.0 mm thick glass) shutter including necessary locking arrangement by allan key, stove enamelled Fire red finish (as per IS : 5, shade no. 536) with " Fire Hose" marked on front, suitable for housing 2 nos. Hose pipe, 1 No. branch pipe .

Supply & installation of swinging type First Aid hose reel in red colour drum with 30 mts long and 20 mm dia heavy duty rubber water hose, 20 mm dia gate valve stop cock, (IS:778, class - II) terminating with G.M. Coupling & nozzle of 6mm outlet with shut off valve confirming to IS 8090 complete with MS socket for tap-off, drum and brackets (including painting) for installation on wall with anchor fastner, bolts & nutsconforming to IS:884 complete as required.

Supply & Installation of Four Way Fire Brigade Inlet Connections for each wet riser Supply & Installation of Cast Iron body fire brigade inlet breaching head as per IS:904 Specification with 63 mm dia instantaneous type inlet and 150mm dia flanged outlet with built-in check valve for fire brigade connection etc. complete with 150 NB Gate valve and 150 NB Non return valve.

Supply & installation Auto Air vent for risers, suitable for pressure not less than 15 Kg/Sq.cm.

Supply & Installation of 25 mm NB, drain valve for each wet Riser

Sprinkler System Supply, Installation, testing and commissioning (SITC) of piping complete confirming to IS: 1239:2004 and IS: 3589:2004 Heavy Grade Galvanised with suitable type of supports, anchor fastners, bolts & nuts (Galvanised), clamps, fittings such as Reducers, Tees, Elbows, Flanges. Including cutting, welding, fixing in RCC trench by using suitable supports. 200 NB

Supply, Installation, testing and commissioning (SITC) of Gate Valve 200 NB

Excavation & Back Filling for the following items Soft Soil

Hard Soil

Soft Rock

Hard Rock

Supply, Installation, testing and commissioning (SITC) of Sprinkler Check (Alarm) Valve Sprinkler Alarm Check Valve complete with all factory made standard trims, pressure gauges, drain valve, etc.150 NB

Supply, Installation, testing and commissioning (SITC) of Pipes confirming to IS:1239 Pt 1 & IS:3589 Heavy grade GALVANISED , including cutting, threading, welding etc. and providing all fittings e.g.. elbows, reducers, clamps, UL listed hangers and pipe supports, fastners , flanges, gaskets, nuts, bolts and washers etc. It shall be including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade. It shall be including cutting holes and chases in brick or rcc walls/slabs and making good the same etc. complete in all respect as required. 150 NB

Sprinkler (UL Listed) Extended Coverage Pendant sprinkler of 80 degree Celsius with escutcheon plate

ZONE CONTROL VALVES (Gate valve) 150 NB

Inspection Test Connection Supply & Fixing of inspectors test assembly complete with test valve, sight glass sectional drain valve, union; necessary piping, threading, jointing & with corrosion resistant orifice all complete strictly as per drawing.

Supply & installation Auto Air vent for risers, suitable for pressure not less than 15 Kg/Sq.cm.

Providing and fixing MS cabinet (size 600 x 450 x 150 mm) fabricated from 16 gauge MS sheet with full front glass door & locking arrangement with suitable shelves for keeping 15 Nos. spare sprinklers of each type & one no. spanner properly fixed in shelves. Cabinet shall be painted with enamel paint of approved shade.

PORTABLE FIRE EXTINGUISHER SYSTEM SUPPLY & INSTALLTION OF PORTABLE FIRE EXTINGUISHER SYSTEM AS PER IS 2190 & 15683 Dry Chemical Powder Fire Extinguisher 9 Kg capacity

Carbon dioxide (CO2) Fire Extinguisher 4.5 Kgs capacity

Carbon dioxide (CO2) Fire Extinguisher 2.0 Kgs capacity

ELECTRICAL POINT WIRING AND SUBMAINS Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.Group C

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

CABLES & CABLE TRAYS LT Cables Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size:- 2C x 6 Sqmm Cu

4C x 6 Sqmm Cu

4C x 10 Sqmm AL

3.5C x 25 Sqmm AL

3.5C x 120 Sqmm AL

3.5C x 150 Sqmm AL

3.5C x 300 Sqmm AL

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2C x 6 Sqmm Cu

4C x 6 Sqmm Cu

4C x 10 Sqmm AL

3.5C x 25 Sqmm AL

3.5C x 120 Sqmm AL

3.5C x 150 Sqmm AL

3.5C x 300 Sqmm AL

CABLE TRAYS Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 70 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 70 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 70 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 70 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Distribution Board Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface / recess, with provision to mount 8 module incomer, 2 module sub-incomer and SP MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Double door-2+4 way (8+6+12),horizontal type

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Single door-6 way

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- Single pole. Cat-A.

Double pole. Cat-A.

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 Amps. Cat-A.

Triple pole & Neutral. Cat-A. (32A)

Lighting Fixtures and Fans Supply, loading, unloading at site, installation, testing and commissioning of LED fixtures complete in all respects such as all clamps, internal wiring between accessories and earthing terminal etc. All LED lighting fixtures shall be provided with drivers and shall be a part of the lighting fixtures. Surface mounted Industrial Batten LED fixture of Philips BN308C LED20S-6500 L12O PSU WH or equivalent

Surface mounted Industrial Batten LED fixture of Philips BN308C LED40S-6500 L120 PSU WH or equivalent

15W LED surface mounted Philips SM251C LED20S-6500 PSU WH or Equivalent

Recessed mounted circular downlighter LED fixture of Philips DN092B LED10S-6500 PSU WH or Equivalent

10W LED Mirror light BN021 LED10S-6500 PSU GR-S1 or Equivalent

Exhaust Fan :Supply, installation, testing & commissioning of Exhaust fan of 300 mm dia. 900rpm single phase heavy duty complete with all accessories.

Earthing System Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for pipe earth electrode complete as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Supply, installation, testing & commissioning of following sizes of G.I./Cu strip/wire clamped to walls, cable trays, cables in recess or surface etc for equipment /system earthing complete as required including inter connection between length at joints, all fixing accessories saddles clamps etc, and other fixing hardware material as required for proper installation. 50 x 6 mm strip GI

Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for earth connections etc. as required.

Providing and fixing 25mm x 5mm copper strip on surface or in recess for earth connections etc. as required.

Providing and fixing 6 SWG (4 mm dia.) G.I. wire on surface or in recess for loop earthing as required.

Lighting Protection System Supplying and fixing G.I. tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run)

Supplying and fixing G.I. tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck,nuts and spring washers etc. complete as required.

Supplying and laying G.I. tape 32mmx6mm thick from earth electrode directly in ground as required.

Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Distribution Board and Pannel LT Panel cum APFC Panel as described above

METERING PANEL-SHOPS (6th Floor) as described above

DG Set 125kVA

OIL TANK Supplying, unloading, fixing and commissioning diesel oil storage tank of 225 litres capacity made of 3 mm MS sheet with manhole, glass gauge, inlet and outlet connections with gate valve, drain plug, piping between tank and engine, vent etc. mounted on suitable MS staging to maintain gravity flow of diesel oil from tank to DG Set including painting.

Supplying, fixing, connecting of fuel pipe supply & return of class C MS pipe from raised service tank to day tanks inside canopy of suitable dia.

Safety and Fire Protection Equipments Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and fixing H.T.danger notice plate of 250mm x 200mm made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Supply and fixing wooden framed covered with glass shock treatment chart printed on cloth in English ,Hindi & Local language.

Supply and fixing suitable size wooden framed covered with glass for Main Panel SLD in electrical room as per IE rules fixed to wall as required.

Supply and providing ISI marked electrical 1.1 kV grade 3 mm thick anti-skid rubber mat, 2 x 1 mtr as per IS:15652-2006 with up to date amendment.

Supply, installation, testing and commissioning of Standard First aid box complete with all accessories as required.

Co2 type duly refilled 4.5 Kg & ready to use

5kg DCP type Fire extinguisher

Providing & fixing 4 nos. fire buckets with stand.

Providing & fixing of 'No Smoking' and 'No Unauthorized Entry' signboards in English and Hindi, as per IPR- 1970.

Passenger Elevators MRL (680 kg) 10 Persons, 7 stops , 1.75 mps & rise 21.6 mtr. a) 2150 D x 1900 mm W

ICT Fire Detection & Alarm (FDA) System Supply, installation, testing & commissioning of Networkable Intelligent Addressable Fire Alarm Control Panel (EN/UL Approved) having provision of 1 loop with each loop capable of connecting upto 99 detector and 99 devices, with minimum 200 character LCD display, multiple access levels, event history file in non-volatile memory (EEPROM) to store 20000 events, including Loop driver cards, network card, in-built battery backup for 72 hrs in standby mode & 30 min in alarm condition mode in metal enclosure and other required accessories. 1 Loop

Supply, Installation, Testing and Commissioning of Work station with PC with Printer and with GUI based network software (License FOR 250 devices) capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various sensors locations or device locations with Required communication Network modules to Run the GUI based Building Integrator.

Supply, installation, testing & commissioning of follwing type Addressable detectors (EN/UL approved) with detector mounting base and other required accessories. Photoelectric type Smoke detectors

Heat detectors

Supply, installation, testing & commissioning of Hooter in ABS plastic body having sound adjustible Db level upto 90 dBs and a multi tone facility and light ajustable to 110 candelas complete with mounting base, enclosure & required accessories.

Supply, installation, testing & commissioning of follwing Break Glass Type Manual Call Points in having "Break glass" message embedded on the glass with required accessories.

Supply, Installation, Testing & commissioning of 2 core1.5 sq.mm,FRLS , Armored , Shilded Cablewith saddle and required accessories

CCTV System Providing, installation, testing and commissioning of Fixed IP Indoor Dome Day/Night IP High Definition Camera, ONVIF Profile G compliant.

Providing installation testing and commissioning IP based Bullet PoE Camera (IP 66) with variable focal lens (12 mm) on ceiling/ wall or other desired location with mounting accessories.

Providing installation testing and commissioning of 32 channel NVR (Network Video Recorder) with 26 TB Storage including all connections as required.

Supply, Installation, Testing and Commissioning of Work station with PC for CCTV System

Providing installation testing and commissioning of 42" size LCD MONITOR at desired location including all accessories, connections etc as required.

Design, Supply, testing, installation and commissioning of Network Switch (L2 Manage POE Gigabit Switch) 8-ports 10/100/1000 Base-T POE Smart Switch plus 2 SFP, SFP transceiver need to be considered separately.

Supplying and laying following sizes one number PVC insulated, PVC sheathed, steel armoured, copper conductor controle cable of 1.1 KV grade in exiting PVC/ GI pipe etc as required. 3 x 1.5 sq. mm

Supplying and drawing UTP 4 pair Cat 6 LAN cable in existing surface/ concealed steel/ PVC conduit as required.

Smart Parking Management System Supply, Installation, testing & commissioning of Ultrasound Detector to sense the vehicle occupancy with automatic detection range set up. Operating voltage @ DC15~24V,with minmum Power consumption, Ultrasonic Sensing with RS485 as communication protocol, detectable range of 0.3m~4.5m, operating temp:-20～+50 Degree celcius with Standard Baud rate & Housing Material with all required mounting connectors & Accessories as per specifcation.

Supply, Installation, testing & commissioning of LED Iindicator (RED/GREEN/BLUE).Common-anode double color light design, Operating Voltage @DC18~24V,LED Luminance for Green-9000mcd & RED - 5000mcd & Blue- 3200 mcd for Disables indication with all required mounting connectors & Accessories.

Supply, Installation, testing & commissioning of ZONAL CONTROLLER equipped with digital filtering technology. Operating voltage @AC220V, 50Hz,output voltage:DC18V (DC24V optional) communication protocol: RS485, Indicator light with Standard Baud rate & the above shall be housed in a vandal proof, lockable & secure MS powder coated Cabinets to be supplied along with the Controllers & all other Required Necessary Accessories As per Specification.

Supply, Installation, testing & commissioning of MASTER CONTROLLER. Operating voltage :AC220V± 10%, Power consumption:10 W, Communication protocol : upward RS232/ downward RS485, with Standard Baud rate & the above shall be housed in a vandal proof, lockable & secure MS powder coated Cabinets to be supplied along with the Controllers & all other Required Necessary Accessories. As per Specification

Informatory Signs Boards Supply, Installation, testing & commissioning of Main Display at Entry Of basement & first floor of Building : 1 ROW LED DISPLAY 3 Numeric Character (For indicating total empty slots at respective level).LED DISPLAY with (At main Entrance)

Supply, Installation, testing & commissioning of SINGLE ROW LED DISPLAY 3 Numeric Character (For indicating total empty slots at respective floor level).LED DISPLAY with

Supply, Installation, testing & commissioning of LED DIRECTION DISPLAY (For guiding the vehicle through parking levels and to the exits). With 2 Numeric Character of 4" Height

Parking Guidence Serever with Software Supply, Installation, testing & commissioning of GUI Server with Software (Windows 7 based embedded OS, 24" monitor, keyboard), with PGS Software. The software will get the realtime data from the ultrasound sensors to calculate the total occupancy levels and free space availabilty and will create the respective output to the direction/ counting displays baywise and floor wise. it will also give the realtime graphical representation of the floor occupancy on the software .

Parking Management System Supply, Installation, testing & commissioning of Automatic Ticket Dispensor with proxy card reader inbuilt with printed information about the car park access (date, time, terminal number, etc.),Entry bar-code ticket printer, Ticket exit slot specifically to protect them (weather, incorrect extraction when half printed, etc.), 125kHz proximity isocard subscribers reader, 2 channel loop detector included, Electronically regulated interior heating and ventilation system, blinking high-visibility pushbutton (flush mounted + Anchor Base) with all required mounting connectors & Accessories as per specifcation.

Supply, Installation, testing & commissioning of ANPR/LPNR Camera IP Camera to take JPEG Image of Vehicle Registration Number

Supply, Installation, testing & commissioning of Automatic Motorized Boom Barriers with Signal ( Indication ) light at ENTRY & EXITS up to 3 m length Opening Closing Time <2.5 Sec, along with Vehicle loop detector.Compatible with card reader system,code or biometric devices. Quoted price shall be consider cabling for cabling between the Boom Barriers and the motor control center, card reader, push button, loop detector, controller & all necessary accessories

Supply, Installation, testing & commissioning of Manned Payment Booth at EXIT consisting of POS (Windows 7 based embedded OS, 18.5" monitor, keyboard), POS License, Bar code Ticket reader, Usb/Rs232 converter, Receipt barcode ticket printer for Manned Station, Courtesy display for Manned Station, 125kHz Isocard reader for manned station

Supply, Installation, testing & commissioning of Parking Software with licence for all Nodes

Cables & Accessories Supply, Installation, testing & commissioning of CAT 6 Cable including 20 mm PVC Conduit.

Supplying, installing, testing and commissioning of 4C x 1 Sq mm Annealed Tinned Copper Shilded armoured Multistrand cable for signal / power (from Sensor & Devices to Controller).

Supplying and laying of 3C x 2.5 sq.mm 1100 volts grade PVC insulated sheathed copper conductor armoured Power cable for Physical security equipments.

Misc Cables - If required

UPS for entire system 5 KVA UPS

Yashwant Singh Diwan