CWE/P-83/2020-21 SPECIAL REPAIR TO BLDG NO NP-79 (MD ACCN) AT BHADOURIYA COMPLEX UNDER GE (SOUTH) PATHANKOT

Amount

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and including taking out existing roof treatments, brushing neat cement slurry with 3.0 Kg of cement per sqm complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in padding over roof slab for providing proper slabs 1:40 and approx thickness 75mm or less, and finishing the surfaces even & smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:4 mixed with WPC @ 3% by weight of cement on fair face of concrete roof surface finished even & fair to receive treatment on roof complete all as specified and directed

Supply only intergal water proofing compund complete all as specified.

Providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane complete all as specified and directed. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

M & L 40 mm thick brick tiles laid on 15 mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified and directed

M&L taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out hold fast complete all as specified and directed.

All a per Srl item No 7 here in before but exceeding 1.5 Sqm but not exceeding 4 Sqm (without taking off shutters from the frames) complete all as specified and directed

Taking down shutters of any description exceeding 1sqm and not exceeding 2 Sqm each, complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 165 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated complete all as specified and directed..

M&L factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated complete all as specified and directed..

M&L factory made solid PVC puff door frame of size 90 x 55 mm made out of 5 mm thick plain colour PVC sheet with one or more rebate reinforced with MS square tube fixed in opening as per specifications and drawings No CEPZ/TD-378/11 sheet No 1/1 etc complete all as per specified and directed.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site all as specified and directed

S&F for Steel windows with tubular frame factory made with double shutter (wire gauged shutter & glass glazed shutter, wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl projecting type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and including 10mm square bar grills complete, including two coats of synthetic enamel paint over one coat of red oxide primer all as specified & pattern shown in drg No CEPZ/ID-245/01 and 246/02 sheet ½ & 2/2 complete all as specified and directed.

S&F steel ventilator with tubular frame factory made of size 79mmx39mm, 16 gauge rectangular tubular frame with side hung shutter ,bottom portion glazed and top portion gauzed shutter with glazing bars 12x3mm flat iron including projecting type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and including 10mm square bar grills and frosted glass and wire cloth complete, including two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

Supply and fixing extruded Aluminium alloy handle fabricated anodised, 150mm size (ISI marked) complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled, 100mm long, complete all as specified and directed.

Supply and fxing Mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 300mm long, complete all as specified and directed.

Supply and fxing , 250mm thick aluminium with hasp and staple bolt type and fixing clips of sheets cast or extruded section and fixing bolts and sliding bolts or extruded section complete all as specified and directed.

Supply and fxing , 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate (ISI marked) complete including all neccesary welding if required complete all as specified and directed..

S & F for floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor over all length of cover plate 140mm thick complete all as specified and directed.

S & F galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Hacking out old broken glass 3.0 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each panes complete all as specified and directed.

M&L 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE complete all as specified and directed..

M&L preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of colour as approved by GE complete all as specified and directed.

M&L preparation of new wooden surface and applying two coats of synthetic enamel paint with a coat of pink primer of any description, not otherwise described over 10cm width or girth, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

M & L prelaminated particle, board 18/19mm thick , exterior grade,prelmainated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cup board shutters and shelvs complete all as specified and directed.

M&L for continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30mm complete all as specified and directed

M&L for hasp and staple, 100 mm long aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed (ISI Marked)

Taking down old eaves gutters and rainwater pipes (any size or pattern), including all fitting, head, shoes, bend, swan-nacks etc, including cleaning for refixing or removal to store complete all as specified and directed.

M&L PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint fixed to walls as drainage pipe complete all as specified and directed.

M&L PVC (SWR) shoes 110mm dia complete all as specified and directed.

M&L PVC (SWR) bends 110mm dia complete all as specified and directed.

S&F in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 450 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc including provision of cement concrete bedding complete, all as specified and as directed.

S&F in repair PVC valve less symphonic action type flushing cistern 10 litres capacity , low level white with inlet ball valve float and handle including brackets including flush pipe for low level cistern including all joints ,complete all as specified and as directed.

S&F in repair Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

S&F in repair centre hole basin mixture valve, cast copper alloy fancy type 15mm brass chromium plated mixer (central hole basin mixer w/o pop up waste system) for mixing hot & cold water screwed down for iron pipe fixed in repair, complete all as specified.

Supplied and fixed Rotational moulded polyethlene water storage tanks of 500 ltrs capacity ISI marked (cylindrical vertical with closed threaded top cover) hoisted and fixed in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old broken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M&L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item no 46 here in before but except tubing complete all as specified and directed

M&L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item no 48 here in before but except tubing complete all as specified and directed

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick masonry, complete all as specified.

Supply and fixing in repairs Bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type with long shank with capstan head, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing in repairs, concealed stop cock, fancy type , chromium plated (ISI marked) with long shank and cup , screwed down, high pressure, with capstan head, screwed both ends for iron pipe of 15mm bore, complete all as specified and directed.

M&L 15mm bore swivel shower of PTMT any colour for fixing with 15mm pipe including shower arm 15mm size, 195mm long with bend of 45 degree with flenge of PTMT (Minimum weight 40gms) fixed in reapairs, complete all as specified and directed.

M & L 15 mm Stop valves/ Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

Supply and fixing CP wall mixture, valve cast copper alloy fancy type for mixture hot and cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia complete all as specified.

M&L Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl necessary brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

M&L Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S&F Chromium plated towel ring fixed with brass screws complete all as specified. (ISI marked)

S & F soap dish of CP fixed with and including chromium plated brass screws and wooden/plastic plugs, all as specified and directed.

S&F stainless steel plate rack 600x750mm made of 1mm thick sheet of approved make fixed with mild steel screws , complete all as specified.

S&F in repair 100 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints laid in floors, complete all as directed

S&F in repairs 100 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

S&F in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm ISI marked, complete all as specified.

S&F in repairs cast iron bends (any radius) with duck's foot or heel rest for 100mm dia of pipe, complete all as specified.

S&F in repairs, cast iron floor trap of 75mm dia of outlet, with grating including jointing to waste pipe with fixed in cement concrete 1:2:4, type B-1 complete all as specified.

S&F 75 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints laid in floor, complete all as directed

S&F 75 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

Supply and fxing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm ISI marked, complete all as specified.

S & F 50 mm dia cast iron cowl complete all as specified and directed.

S&F 50 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

S&F Stainless steel sink 1mm thick for kitchen with plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically described complete all as directed by Engineer-in-Charge.

M&L PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) as in sunken portion all as specified and directed by Engr –in Charge

M&L for rendering 15mm thick in cement mortar 1:2 and mixing with WPC 3% by weight of cement complete all as specified (WPC paid separately)

S&F for applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per Sqm and binding with clean dry sand @ 0.05 Cum per Sqm complete all as specified

S&F for polyethene film, 50 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 Kg per Sqm cement complete all as specified

Demolition of cement concrete (reinforced) any description and in any position not otherwise specifically described complete all as directed by Engineer-in-Charge.

M & L Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:6) including necessary form work complete all as specified and directed by Engineer-in-Charge.

TMT bars, 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified

M&L 20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layer in cement mortar 1:4 etc complete all as specified and directed. Note:- The stone slab shall be in one piece over kitchen plateform,making gas pipe holes 25mm dia with rounded holes throughout the depth of granite & slab and all open edges to be half rounded.

M&L 20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layer in cement mortar 1:4 etc for skirting of vertical surfaces complete all as specified and directed. Note:- The stone slab shall be in one piece over kitchen plateform,making gas pipe holes 25mm dia with rounded holes throughout the depth of granite & slab and all open edges to be half rounded.

M&L machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including screed bed or bedding layer 20mm thick in cement mortar 1:4 complete all as specified and directed. Note :-The size of kota stone shall not be less than 55 cm x 55cm & Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine.

All as per Srl item No 84 here in before but on vertical surfaces on 10mm thick cement mortar 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified & directed.

M&L rendering 10mm thick on concrete surface in CM 1:3 in facia or edging of chajjas, ceiling and roof projection etc incl taking out pealed off plaster/concrete and making good to cracked RCC surface in true line /shape by providing RCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate including all necessary form work to thickness at required at GF and FF finish even and smooth without using extra cement complete all as specified and as directed by eng-in charge. NOTE- the rate will be inclusive of scafolding for single or double storey including making hole in brick work and making good in cement mortar.

M&L 75 mm thick cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as in plinth protection in panels, joints filled with bitumen mastic including finishing the surfaces even and fair including demolition of exisying concrete in plinth protection, path etc complete all as specified and directed

Demolition of brick or stone masonry, in ground floors and paving not exceeding 15cm thickness, complete all as specified.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), all as specified and directed.

All as per Srl item No 90 here in before but ecxept bricks complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base for receiving floor tiles and mass concrete all as specified and directed by Engr –in Charge

M&L Glazed ceramic coloured tiles in skirting/dado 350 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M&L Non skid coloured ceramic tiles 600x600mm 9 - 10 mm thick area of each tile in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6) for laying floor finishes, complete all as specified and directed.

M&L Non skid coloured ceramic tiles 600x600mm 9 - 10 mm thick in dado/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 10mm thick screed bed in CM (1:4) for laying floor finishes, complete all as specified and directed.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 15mm thick cement plaster rendering in CM 1:4 on fair faces of stone masnory/brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L 15mm thick cement plaster rendering in CM 1:6 on fair faces of stone masnory/brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L Preparation of new plastered surfaces of walls and applying two coats cement base paint of approved brand all as specified and as directed .

M&L Preparation of old plastered surfaces of walls and applying two coats cement base paint on walls of approved brand all as specified and as directed .

M&L Preparation of old plastered or unplastered surfaces of wall /facia/Chajjas etc of any description and applying one coat of weather proof exterior emulsion paint over a coat of primer complete all as specified

M&L Preparation of newly plastered or unplastered surfaces of wall /facia/Chajjas etc of any description and applying two coat of weather proof exterior emulsion paint over a coat of primer complete all as specified

M&L three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M&L two coats of white wash including preparation of old plastered surfaces of ceiling complete all as specified.

M & L for complete removal of existing treatment from internal/external surfaces of wall by brushing with wire and washing, rubbing down and stopping of surfaces complete all as specified and as directed .

M&L for preparation of surfaces by leveling/edging of the disturbed planes/edges of old/new plastered surfaces of wall by using wall care putty of 1 to 2 mm thic on vertical surfaces to true vertical and horizontal lines of bricks/concrete walls finish to even and smooth with two layers of screylie wall care putty complete all as specified and as directed

M&L Preparation of existing finished by wall care putty surfaces of wall and applying one coat of asian primer over two coat of oil bound distemper on old walls surfaces complete all as specified and as directed

Supply and fxing in repair curtain rod 25 mm dia pre painted synthetic enamel paint of wooden finish , fixed with screws complete all as specified.

Supply and fxing in repair wooden (turned, weathered & mitred) brackets of Ist class hard wood pre polished with french polish and touch wood with cut hole suitable for 25 mm dia rod fixed with screws and gutties in wall, complete all as specified and directed.

All as per Srl item No 113 here in before but end caps with wall ornament and fixed to curtain rod with screws of design/shape complete all as specified and directed.

M&L for Cement concrete (1:3:6) type B-1 using 20mm graded stone aggregate as in copings, bands, plinth courses, string courses, lacing courses, kneelers, apex stones, bed plates, including necessary form work complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

M&L 75 mm thick cement concrete (1:3:6), type C-1 using 40mm graded stone aggregate as in floors, hard standing etc and laid in alternate bays complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed

M&L for sand filling under floors or in foundations including watering and consolidation including spreading and levelling in layers not exceeding 25 cm thick complete all as specified and directed

M&L Machine pressed coloured rubberised finished precast concrete interlocking paver block any shape and size as approved by GE confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment laid over complete all as specifiecd and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M & L Point wiring for light/fan point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for switches and sockets, including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be in each point etc. b) On RCC roof ceiling PVC conduit shall be provided on surfaces of any necessary point with proper fixing clips and no extra cost shall be paid for job etc all as directed (c) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per above item no 121.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 121.00 here in before but for one socket outlet 5 amp on independent board all as specified and directed

All as per above item no 121.00 here in before but one for light point controlled by 2 nos two way 230 Volts switches complete all as specified.

M&L Point wiring with 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for one 3 pin socket outlet 15 Amp on independent board including 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) complete all as specified and directed.hite wash/colour wash to matching with the existing colour complete all as specfied and directed.

S&F Switch piano flush type 5 Amp single pole one way, 5 amps, 230 Volts (ISI marked), complete all as specified.

S&F switch socket combination 2 in 1, 3 pin, 5 Amp & 15 Amp flush type ,complete all as specifed.

S&F Switch piano flush type 5 Amp single pole two way, 5 amps, 230 Volts (ISI marked), complete all as specified.

S&F switch socket combination 3 pin, 5 Amp flush type complete all as specifed.

S&F switch socket outlet , 3 pin, 2 in 1 flush type , 5 Amp 230 volts complete all as specifed.

S&F switch bell push 5 amp, 240 volt, single pole flush type (ISI marked) , with polycarbonate body one way complete all as specifed.

S&F in replacement fan regulator electronic, step up type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required or directed by Engr-in-Charge. Testing complete after servicing and fixing for smooth and noise free operation.

S&F bell multi music type , AC 230 Volts, Single pole complete all as specifed.

M&L for ceiling rose 2-3 terminal size 65x20mm complete all as specifed.

S&F in replacement sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S & F in replacement existing unsv distribution board iron clad, with double door 4 way with IP-54,1K-09 protection,cemet spill prptector suitable for MCCB as incommer AC 415 Volts three pole with thermal release adjustable type (80% to 100 % ) and MCB as outgoing ,complete with appropriate size copper bus bar and neutral link complete with including one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 25 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).

S & F MCBs (SP) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution complete all as specified and directed

S & F MCBs (SPN) 6 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution complete all as specified and directed

Supply and Fix decorative box type fitting 4 feet long with blue coloured end caps for LED tube 1x20W LED including LED tube 4 feet long of 20W having bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F LED bulk head light fitting 1x10 W suitable connecting including electrically to ceiling rose using cord flexible 3 core PVC insulated overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as directed by Engr-in-chagre

S&F in replacement existing UNSV Sleek LED mirror light fitting 2 feet long 1x10 W with complete all accessories pre wired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor. Cable of size 0.75 Sqm 3 core complete all as specified and directed.

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S&F LED Lamp 230 volts,50 Hz,inverter LED 18/20 watt ,lumen 900 lm, rated current 0.045A, CRI >80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

S&F LED Lamp 9 Watt, 240 Volt 230 volts, complete all as specififed and direccted.

S&F sheet metal enclosure single pole and neutral with a 2 pin and earth plug and socket 20 A 240 V complete with one single pole MCB of capacity 20 A complete all as specified and directed.

S&F 1200mm sweep ceiling fan, energy saving 5 star rated, with remote control and BLDC motor complete with canopy, blades downrod split pin etc complete of approx wattage 30 to 32 watt rated suitable for operation on AC 220-240 V AC, 50 Hz, PF>0.95, Air delivery approx 230 cum/min with 5 speed control complete all as specified and directed.

S&F Domestic Exhaust fan steel body of 300 mm sweep with louvres higher air flow, low noise suitable for 230 Volts AC 50 Hz electric supply including connecting to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

Supply & Ventilation fan AC sinlge phase 230/240 volts of size 200 mm sweep having plastic body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

S&F Geyser 25 Ltrs capacity, 230 volts, vertical type with BEE star rated, 5 stars rating suitable for 8 bar pressure with nano polymer coated tank, incoloy heating element, rust proof ABS body etc incl necessay drilling, provn of anchor bolts of suitable size and making electrical connections complete all as directed by Engr-in-charge.

M&L Earthing complete with galvanised steel earth plate electrode of size (60 x 60 x 6) mm thick buried directly into ground (Earth pit not less than 2.25 metre below normal ground level) with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, connected to galvanized iron wire 4mm dia as earth lead by means of bolt nut, check nuts and washers of GI and provision of GI tubing medium grade (ISI marked) of size 15mm for protection of GI earth wire upto test point, 20 mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle of size 40x40x4mm, adequate quantity of charcoal dust and salt layers all around the earth plate, excavation, earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR part-1 and all specified or indicated including testing on completion Note: Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth strip upto 7.5 m long for connecting to test point etc all as required at site for complete earthing..

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35sqmm 3.5 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of GI pipe/LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

M & L Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Cutting and existing steel tubing for alteration or addition including screwing existing steel tubing to form connection/branch pipe etc for 40mm bore pipes complete all as specified and directed.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

jagdambe traders

M/S BISHAN DASS AND SONS

Surya & Gautam Builders

M/S Ajay Kumar Mahajan

VIKRAM SINGH MANHAS

malghotra construction co