SPECIAL REPAIRS TO ROOF SHEETS OF BLDG NO.P-2 OTM ACCN AND CERTAIN LBW REV WORKS

Amount

S&F pre- coated coloured Galvalume Aluminum Zinc coating GI based corrugated steel sheet profile pattern 0.50 mm thick of any colour having tensile strength of 550 Mpa (AZ150) as in roof covering/ clading to wall, including crimping sheet at end fixed with self tapping screws complete all as specified and directed

S&F pre-coated Galvalume Aluminum Zinc coating GI based corrugated steel sheet profile pattern 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ150) as in ridge 0.6m wide fixed with self tapping screws complete all as specified and directed

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St-240 complete all as specified and directed

Excavation over areas not exc 1.5m deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep in any type of soil for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sqm on plan and getting out complete all as specified and directed.

M&L for moorum/red bajri filling in trenches or paving laid in layers not exceeding 25 cm thick spread, levelled and rammed including watering complete all as specified and directed.

Removing excavated materials (soil) to a distance exc. 1.50 km and deposting where directed, at a level not exc 1.5m above the starting point complete all as specified.

Returning filling in, incl spreading, levelling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggregates) as in mass concrete, foundation filling, etc., complete all as specifed and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc basement slabs, under reamed plies and mass concrete, complete all as specified and directed

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Columns, pillars, piers, posts and struts and the like, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span and the like, complete all as specified and directed.

M&L mild steel "TMT" bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending sprially for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with chips complete all as specified and directed.

All as per Srl item No. 13 above but for 5mm dia and over upto 10 mm dia and including 10mm dia in stirrups, spacers and binders -ditto-

M&L for form work to sides & soffits of plinth beam and sides of footings getting for fair finished surfaces of concrete complete all as specified and directed.

M&L for form work to sides of columns as in fair finished surfaces of concrete complete all as specified and directed

M&L for formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. for fair finished surfaces of concrete flat complete all as specified and directed

M&L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as per specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as sub bases of floors and finished the surface even and rough to receive the topping layer complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in levelling course of sub base finished even and rough to receive the topping layer, complete all as specified and directed

M&L for joint free non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with laid over and including 15mm thick screed bed layer in CM 1:6 complete all as specified and directed.

All as per Srl item No.21 but in dado / skirting etc with & including 10 mm thick rendering in CM 1:4 -ditto-

M&L for 75mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in plinth protection surface finished even & smooth using extra cement providing with construction joints 10mmx20 mm filled with bitumen and sand mortar 1:3 complete all as specified and directed.

S&F aluminium windows and ventilators sliding type three track powder coated consisting of frame 91.80 mm x 45 mm shutters 39 mm x 18 mm with rollers and locking arrangements with 4 mm thick plain glass with rubber gasket and aluminium beading , Al. handle,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.45 mm dia etc including necessary cutting holes on wall and floor and confirming to IS complete all as directed by Engr-in- Charge (Al. section thickness 1.50 mm )

S&F glazed aluminum door powder coated of any colour consisting of frame of 63mm x 38 mm size with shutter fixed on frame both side openable on pivotal arrangement with including necessary cutting holes in wall & floor Door shutter consists of top rail size is 84.45x44.45 mm , bottom rail & lock rail size is 101.80 x 44.45 mm & style of door shutter is 83mmx 44.45 mm glazed with 5mm thick tinted /colour glassof approved make with handles 2 Nos in each door , hinges has fitted on frame as required fixed with rubber gasket & aluminum beading any No of panels with aluminum handle , locking arrangemen,floor spring and floor door stopper incl. necessary joining cleats , glazing clips etc complete (aluminum section thickness 2 mm) confirming to IS complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:4 on even surface of brick wall mixed with 3% WPC finished even and smooth without using extra cement, complete all as specified and as directed. (Note:- Water proofing compound shall be measured and paid separately under respective items).

M&L for 15 mm thick rendering in cement mortar 1:6 in other than fair faces of brick work finished even & smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed

M&L for prepration of newly plastered wall sufaces & applying two coats exterior emulsion weather proof paint over one coat of exterior wall primer incl of walls complete all as specified and directed . Make:- Asian ACE or equivalent make as approved by GE

M&L for preparation of newly plastered surfaces of wall and applying 2mm thick Birla / J K wall care white putty on walls and applying two coat of Interior Acrylic emulsion over a coat of alkali resistant primer complete (internal wall) complete all as specified and directed.

M&L for suspended false ceilling comprising of 4 mm thick non asbestos fibre cement bulding boards of size 595mmx595mm ‘E’ Board Classic Design Lake & hill including supply and fixing GI ‘Tee” grid frame work made of special section of M.S galvanized sheet 0.30mm thick , bottom portion painted with cellular nitro painting, warping the suspending wire around the existing wooden/steel purlin /rafter for suspending grid frame work of size 605mmx605mm suspended with 4 mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mmx24mmx0.60mm, cross runner tee 37mmx24mmx0.60mm and perimeter angle of 24mmx24mmx0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450 mm c/c along the perimeter of wall including applying two coats of distemper oil emulsion complete all as specified and directed

M&L for 18mm to 20 mm thick pre-polished Granite slab, machine cut, for floors/ shelves,cooking platforms window cill, steps, jambs and pillor top laid over 15mm thck CM 1:4 cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone complete all as specified and directed.

M&L for rounding, chamfer, splays or arris and smooth finishing at the edges of stone as in steps, cooking platform and other similar locations complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured chemically treated rubber moulded interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658 - 2006 of 80mm thick, M-35 grade complete all as specied and directed.

M&L for machine pressed precast cement concrete coloured chemically treated rubber moulded interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658 - 2006 of 60mm thick, M-35 grade complete all as specied and directed.

M&L for crushed quarry stone dust filing under floors or in foundation or cushion bed for paver blocks complete all as specified and directed

M&L for PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Dismantling Asbestos cement (corrugated semicorrugated etc ) sheets in roof covering complete all as specified and directed.

Dismantling AC Sheets Ridge/hip for (corrugated semicorrugated etc ) sheets in roof covering complete all as specified and directed.

Dismantling unframed timber scantlings 40 sqcm & over in section, in any position complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description complete all as specified and directed..

S&F structural steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc complete all as specified and directed.

S&F MS plates (plain or chequered) channels square cut to or notched forming holes with riveted bolted or welded attachment conforming to Fe-410W complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 22.5cm & not exc 30cm long, dia of shank 16 to 20 mm complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified & directed.

M&L for preparing the new plastered suface of the wall and applying three coats of white wash on walls surface complete all as specified and directed.

Demolition of existing ceiling boards (fiber, pulp, insulation, etc.) or insulation board/slabs/blankets, any thickness, including frames.complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep in soft/loose soil for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 sqm on plan and getting out complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and depth exc 1.5 m but not exc 3.0 m in hard/ dense soil for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sqm on plan and getting out soil complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and depth exc 1.5 m but not. exc 3.0 m in soft/disintegrated rock complete all as specified and directed.

M& for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like and the like, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded aggregates as in chajja and the like and the like, complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; n exc. 200m thick (horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and directed

M&L for formwork to edges of concrete flats, breaks in floor, openings in concrete walls, floors and roofs exc 10 cm but n.exc 20 cm width for fair finished surfaces complete all as specified and directed.

M&L for provn of water proofing roof treatment to non accessible RCC roof with approved modified membrane with non-woven polyster reinforcement of weight not less than 3 kg/sqm comprising with following items complete all as specified and as directed:-

(a) The surface of roof, parapet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut . (b) M&L for 10 mm thick plaster in CM (1:4) mixed with and including water proofing compound @ 3% by weight of cement applied over roof slab, complete all as specified and directed. (Note : WPC Shall be measured and paid separately) (c) Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kg per sqm to be applied on prepared surface till the surface is properly impregnated (d) Applying one coat of hot blown bitumen of 85/25 grade @ 1.20 kg/Sqm (e) Laying of water proofing treatment of weight not less than 3 Kg / sqm APP modified polymeric water proofing membrane composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is sandwitched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc. (f) Applying one coat of hot blown bitumen of 85/25 grade @ 1.20 kg/Sqm over the membrane (g) Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces, complete all as specified and directed at site .

M&L for 150 mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregates) as sub bases of floors and finished the surface even and rough to receive the topping layer complete all as specified and directed.

M&L for 150 mm thick PCC (1:2:4) type B-1 using 20 mm graged stone aggregate as in floors and finished the surface complete all as specified and directed.

M&L for machine cut Kota stone slab of size 550mmx550mm as in flooring 20mm to 22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including cutting of grooves for steps, laid over and including 20 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed

All as per Srl item No.60 above but in skirting / dado /risers of steps including 10 mm thick rendering in CM 1:4 complete including cutting of grooves for steps all as specified and directed.

M&L for second class hardwood plain, solid, straight chowkhat and frames wrought framed rebated on the solid, rounded on the solid or chamfered put together with glue pinned at joints complete all as specified and directed

S&F 35mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides with complete air titght door including rubbers, cleats etc complete all as specified and directed

S&F aluminum, anodized, barrel tower bolts of extruded section 200 mm long complete all as specified and directed

S&F aluminium alloy, anodised, sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F extruded aluminum alloy handle, fabricated type, anodized 125 mm size complete all as specified and directed.

S&F mild steel butt hinges 'medium weight', cold rolled mild steel 100 mm size complete all as specified and directed.

M&L for hardcore of broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed

M&L for rendering 5 mm thick cement plaster in CM 1:3 on concrete surfaces as in ceiling finished even and smooth (without using extra cement) complete all as specified and directed

M&L for prepration of newly plastered wall sufaces & applying Birla / J. K. wall care white putty 2 mm thick for levelling the surfaces & applying two coats exterior emulsion weather proof paint over one coat of exterior wall primer incl. of walls complete all as specified and directed. Make:- Asian ACE or equivalent make as approved by GE

M&L for prepration of newly plastered wall surfaces & applying Birla / J. K. wall care white putty 2 mm thick for levelling the surfaces of walls and applying two coat of distemper oil emulsion over a coat of wall primer incl. preparation of surfaces of walls etc complete all as specified & directed.

M&L for applying three coats of white wash on newly plastered ceiling surfaces including preparation of these surfaces complete all as specified & directed.

M&L for applying two coats of synthetic enamel paint over a coat of primer on Wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surfaces complete all as specified & directed.

M&L for PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) as in kerbs or mud stops,rounded or chamfered on edges complete all as specified.

Taking down carefully copper/aluminum pt wiring (light fan, socket or power) complete including fittings such as switches, sockets, c/roses, lamp holders, tube light fittings, sketch fittings, wooden boards, bell push, call bell, MCBs, & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall/floor complete all as specified and directed

Taking down main switch, DB/change over, TL fitting, MCBs,AC box of any capacity complete all as specified and directed

M&L for point wiring for the following with 1.5 Sqmm PVC insulated FR, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC trunking of size not less than 20mm bore ISI marked ivory white with all accessories such as tee, bend, joint cover including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green:- .

For one light point or fan point controlled by one switch

For 5Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

All as per Srl item No.77 here in before but for power point wiring using with 2.5 sqmm PVC FR insulated, unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as continuous earth wire

S&F switch piano type flush, single pole, one way 5 A 230 V complete all as specified and directed.

S&F socket outlet, 5 pin, 5 Amp, flush type, 230 V complete all as specified and directed.

S&F switch piano type flush, single pole, one way 15 A 230 V complete all as specified and directed.

S&F socket outlet 2 in 1,6 pin, 5/15 A, flush piano type 240 V complete all as specified and directed.

S&F ceiling rose, surface backlit, 63.5mmx48mm size, three terminal complete all as specified and directed.

S&F lamp holder with 9 watts LED bulb insulated with back plate suitable for Angle/Batten fitting complete all as specified and directed.

S&F electronic double space rotary 5 speed type regulator 120-280 V complete all as specified and directed.

S&F MCB SP 240 volt 6 Amp to 32 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.

S&F MCB SPN 240 volt 16 Amp to 40 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar complete all as specified and directed.

S&F double door metallic sheet metal enclosure for DB double door TPN 4 Way 415 Volts with 200 Amps rated bus bars complete all as specified and directed. Note :- Cutting and chasing in stone masonary and making good to disturbed surfaces shall be included in the quoted rate

S&F TPN 63 Amps 415 V including making electrical coming/outgoing connections with lugs/thimbles complete all as specified and directed

S&F LED TL fitting 20/18 watt for surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brighness complete all as specified and directed. Make:- Havells Cat Part No LHEXBLP7PN1W020, 4 feet/Bajaj cat part No BCLSB 20 WH/ CG Cat part No LCTC-18-CDL

M&L for provn of earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate no 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs.

S&F LED Bulk head 13/10 watt designed for modern homes availave in PIR as well as non PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer complete all as specified and directed

S&F surface conduit sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit conduit PVC trunking of suitable size . ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire including taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed

Taking down fan ,sealing cable end,dismantling blades and removing fan and blades to store and refixing/hanging in only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed

Supply and laying in replacement cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 16 sqmm, 4 core complete all as specified and directed

M&L for sand coushioning with dry and clean over and under the cable for protection of cable , 80 mm sand laid before laying the cable 150 mm sand after laying the cable and filling the sand in cable duct of inside the sub station building complete all as specified ans directed

M&L for sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable complete all as specified and directed.

S&F in repair pipe galvanised iron light grade ( ISI marked) 40mm bore with all fittings laid in trenches or on pole, crossing of road,fixed on wall for protection of cables complete all as specified and directed.

M&L for concealed point wiring for one light, point controlled by one switch with 1.5 Sqmm PVC(FR) insulated, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc/square Top blocks at junction for batten holders, ceiling rose etc screws, gutti/roul plugs PVC all as per site requirement including MS sunken boxes made out of ms sheet and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green:-

S&F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep metallic body complete all as specified and directed.

Supply and lay cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 6 sqmm, 2 core all as specified and directed.

M&L for point wiring for the following with 1.5 Sqmm PVC insulated FR, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC Casing caping/ conduit of size not less than 20mm ISI marked ivory white with all accessories such as tee, bend, joint cover including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green:-

For one light point point controlled by one switch

For one 5Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

S&F ceiling fan 1200 mm sweep and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed

S&F in replacement double door metallic sheet metal enclousure for DB double door (IP-42/43) when MCBs to be used SPN 4 Ways, 240V with 200 Amps rated bus bar complete all as specified and directed.

Supply and laying cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 10 sqmm, 2 core complete all as specified and directed.

maharaja construction and suppliers

A Raza Enterprises

M K Construction