ADDN/ALTN TO CERTAIN OMQS AND CERTAIN MINOR WORKS AT AFS PUNE UNDER GE AF LOHEGAON

S&F pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F Rolled Mild Steel roof trusses(framed),trussed ,purlins ,rails and fastenings etc.,confirming to Fe 410 - S including distance pieces, cleats, etc., complete all as specified and directed.

Taking down cement plaster on brick/ stone wall including raking out joints, hacking for key scrubbing down with water etc. and clearing off the premises all as specified and directed.

M & L rendering 15mm thick on surface of brick work/concrete surface in CM 1:6 and is to be finished even and smooth with out using extra cement complete all as specified directed

M & L for 10mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surfaces with mixing of waterproofing compound and finishing the surface even and smooth (without using extra cement) etc.all as specified and directed.(Water proofing compound will be measured separately)

M & L for preparation of new steel/iron surfaces of any description having width/girth exceeding 10cm and applying two coats of synthetic enamel paint over red oxide primer all as specified and directed.

Demolition of Brick/precast concrete block/Stone/boulder masonary walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed

M&L for precast solid cement concrete block masonry exc 10cm in width built with solid blocks Grade C1 (1:3:6 mix) 20mm graded aggregate and set in CM (1:6) all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware /PVC/ AC or Reinforced concrete) set in cement mortar all as specified and directed.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors or wall all as specified and directed.

All as per item No 10 above but 110mm dia

M&L for PVC (SWR) bends of any radius with oval and access door of 75mm dia all as specified and directed.

All as per item No 12 above but 110mm dia

S &F PVC (SWR) cowls of 75mm dia

S & F PVC (SWR) reducers 75mm dia

S &F 110mm PVC (SWR) junction single (Single T) equal or unequal with acess door all as specified and directed.

S &F 75mm PVC (SWR) junction single (Single T) equal or unequal with acess door all as specified and directed.

Taking down or up 15mm dia steel tubing galvanised along with fittings or any other type of pipe and removing to store or cleaning for refixing.

Taking down or up 20mm dia steel tubing galvanised along with fittings or any other type of pipe and removing to store or cleaning for refixing.

M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors in repairs all as specified and directed.

M&L for GI tubing 20mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs all as specified and directed.

Dismantling of PVC water tanks of exc 500 and n.exc 1000 ltr capacity and removing to store and all as specified and directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks (cylindrical / vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of 1000 ltrs capacity.

Disconnecting existing water tank exc 500 ltr and nexc 1000 ltrs, setting aside (for lowering if required) for repair cleaning, removing all scale and dirt etc from tanks and from mouth of circulatring pipes and re-fixing in position all as directed competete.

S&F in repair Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe of 20mm dia bore and fixed complete all as specified and as directed.

Dismantling roof treatment of any description in suspended slabs in roofs,suspended floors, chajjas, landings etc,including cement mortar bedding,padding concrete and rubbish of premises complete all as directed.

Cleaning the surface by roughening, sweeping clean and washing down and applying cement slurry @ 3 kgs/sqm

M&L cement concrete type B-0 1:2:4 (using 12.50mm graded stone aggregate) as in RCC roof surface with mixing of water proofing compound to horizontal or vertical surfaces finished cement concrete surface even and smooth including necessary form work (Water proofing compound will be measured separately)

M & L for 10mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. including water proofing compund all as specified and directed.(Water proofing compound will be measured separately)

Supply only Liquid WPC complete all as specified and directed.

Applying Bitumen Primer conforming to IS-3384 applied @ 3 kg/Sqm and Providing 3mm thick Atactic Polypropyle Polymer(APP) modified water proofing membrane weighting not less than 3 kg/sqm reinforced with non woven polyester matt weighing not less than 150 gm/sqm and applying a coat of blown grade hot bitumen 85/25 over the mebrance @ 1.2 kg/sqm top of membrane surface shall then be finished complete all as per manufacturer instructions and as directed by Engineer-in-Charge.

Applying aluminium bitumen based paint complete all as directed by Engineer-in-Charge.

M&L for applying two coats of smart care dampproof crack seal, with open and widen the cracks in a 'V' shaped groove and provide a strong base for adhesive of crack seal to the surface wire brush and clean the area throughly with water to free it from dust and loose particles any algal/fungal growth must be cleaned using bio-wash such as bleaching powder and as directed by Engineer-in-Charge. Note:- 1. These are two storey bldgs therefore, scafolding arrange by contractor on own expense.

M&L for applying two coats of Damp proof (Acrylic water proof) of fiber reinforced elastomeric liquid on filling of crack seal applied portion on both sides of cracks each side 75mm wide as directed by Engineer -in-Charge. Note:- 1. These are two storey bldgs therefore, scafolding arrange by contractor on own expense.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than than 50gm/litre and UV resistance as per IS 15489:2004 Alkali and fungal resistance, dirt resistance exterior paint or required shade with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @0.9 litre/10 sqm over new surfaces/old surfaces of wall all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm in floors {Superior/Premium quality}, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 6) complete all specified and directed.

S&F aluminium powder coated three track sliding window with two shutters of 5mm thick tinted glass of modigaurd and one shutter of stainless steel wire mesh including good quality of bearing handle, locks, PVC rubber lining including frame work etc complete all as specified. :- Three track bottom – 20957, Three track top/vertical – 20958, Handle – 20606,Interlocking – 20605, Top and bottom – 20604 complete all as specified and directed.

Taking down chowkat with shutter without taking out shutter from the frame exc 1.5 and n.exc 4 Sqm each complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving's not exc 15 cm thickness (below or above ground level)

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in plinth protection etc.including finishing even and smooth without using extra cement complete all as specified and directed.

Taking down chowkat with shutter without taking out shutter from the frame n.exc 1.5 Sqm.

Demolition or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings dressed stonework and precast concrete articles all as specified and directed.

S & F aluminium powder coated frame ( miniumum thickness of powder coating 50 micron) for doors widnow, ventilator with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge (For sliding window )

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane all as specified and directed by Engr -in-Charge.

M&L 9mm thick Prelaminated particle board ,exterior grade having decoratie choice lamination on both sides fixed with aluminium beadings on aluminium frame work all as specified and directed.

M&L for preperation of new concrete /plastered surface of any description, two coat of dIstemper oil emulsion over a coat of primer complete all as specified and as directed complete all as specified and as directed.

M&L for Cutting holes in brick/stone walls in mud/cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed by Engineer-in-Charge.

S &F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

M & L for 25mm thick PCC 1:2:4, type B-0, (using 12.50 mm graded stone aggregate) as in under layer of tile flooring & finishing the surfaces rough to receive screed bed complete as specified and directed.

M&L for vetrified ceramic tiles 10mm thick full body (light shade ) (square/rectangular) polished, area of each tiles exceeding 0.42 but not exc 1.00 sqm in floors over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L for preperation of new plastered wall surface of any description and applayng two coats of cement based paint over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered wall surface of any description and applying three coats of white wash complete all as specified and directed.

M&L for Non-skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 350X250X7/450X350X7 mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg over & including 10mm thick rendering in CM(1:4) complete all as specified and as directed.

S&F Vitreous China Half stall Urinal, flat back, white with grating and union for discharge pipe and PTMT waste coupling with waste pipe (excluding flushing cistern, flush pipe and waste pipe)

S&F Vitreous china wash down water closet scouting pattern, white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device including trap set and necessary concrete complete.

S&F 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed.

S&F in repairs PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long complete all as specified and directed.

S&F Two way bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap).

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: including stainless steel butt hinges and necessary S S screws)

S&F 200mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F GI tubing of 15 mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by the Engr-in-C.

S&F GI tubing of 20mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by the Engr-in-C.

M&L for nonskid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm in floors {Superior/Premium quality}, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 4) complete all specified and directed.

M&L for nonskid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm in floors {Superior/Premium quality}, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 4) complete all specified and directed.

All as per Item No3,4 &5 above but as in skirting/dados over and including 10mm thick rendering in CM 1:4 complete all as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incluidng rubbing and polishing complete including screed bed 15mm thick in cement motar 1:6 complete all as specified and directed.

M&L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with 10mm thick plaster in CM 1:4 all as specified and directed.

Taking down Chowkats or framesn. exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkat with shutter without taking out shutter from the frame n.exc 1 Sqm.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as directed .

S& F stainless steel Butt hinges 100 mm size . Complete all as specified and directed.

S&F almunium powder coated louvers concealed type for ventilltor size 0.60 X0.45 having arrangement of 4/6 blades fixed to almunium frame complete all as specified and directed .

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beadingscrews etc. complete all as specified complete all as specified and directed .

S&F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F Door closer hydraulically regulated, designation No. 3, Almunium extruded sectiom universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S&F floor door spring double cylinder suitable for door shutter upto 100 kg and fixed complete all as specified

S&F Floor door stopper 150mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor etc

S&F Stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F 5.5 mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq mtr in each pane complete all as specified and as directed.

S&F of Collapsible steel gates side hung, considering of channel pickets , pivoted flat bars, top and bottom runners,handles etc, as specified,errected in position and securing runners with hold fasts and brackets, complete all as specified and directed by Engr-in- Charge

Demolition or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings dressed stonework and precast concrete articles all as specified and directed.

Material and labour for suspended false ceiling using anodized aluminum snap grid frame work. Including Hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G I flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete. Exposed metal frame ceiling with 8mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid as per manufacturer instruction all a specified and directed by Enginner in Charge.

Material and labour for providing point wiring with two runs of 1.5 Sqmm multi stranded copper conductor Flame retardant PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core multi stranded copper conductor Flame retardant PVC insulated 1100 Volts grade wire for continuous earthing complete in and including PVC casing and caping with all fittings/fixture etc and open recessed type Plastic Enclosure( Plastic Switch Board ) ISI Marked (IS:14772) for housing switches / sockets all a specified and directed

(a) One light point controlled by one switch complete all as directed by Engineer-in-Charge

(b) One Fan point controlled by one regulator/switch complete all as directed by Engineer-in-Charge

Supply and fix switch piano flush type 5 Amp one way. complete all as specified & directed

S/F Fan Regulator electronic step type 230V, 100 W complete all as directed by Engineer-in-Charge

Supply and fixing LED luminair 600mmx600mm 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complet with driver, holders & LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as directed by Engineer-in-Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as directed by Engineer-in-Charge

S&F MCB DB SPN 08 way IP43 IK-09 with metal door suitable for housing of MCBs complete all as directed by Engineer-in-Charge

M&L for sub main wiring complete with two runs of single core 4 sq mm FRLS PVC insulated unsheathed multi stranded copper conductor 1100 V grade with colour code and one run of 4 sqmm single Flame retardant PVC insulated unsheathed multi stranded copper conducator green colour cable for continuous earthing complete in & including PVC casing & caping with all fitting & fixtures all as directed and specified ( Note Two runs of 4 sqmm copper cable and one run of 4 sqm copper cable including PVC casing & caping shall be measured and paid as one length).

S&F MCB SP 240 Volts, 10 KA C Curve MCB Sp 6 to 32 Amps,complete all as specified and directed by Engr-in-Charge

S&F MCB SPN 240 Volts , 10 KA C Curve MCB Sp 40 to 63 Amps complete all as specified and directed by Engr-in-Charge

Please Enable Macros to View BoQ information