Rajbhawan colony sthit awas no-1 (purana) type-6 me kitchen ki neechi pipe line ko uncha karne ke phalswaroop aagan me kota stone ki marramat karne ka karya, lawn me interlocking tiles lagane ka karya, ek asthai shade banane ka karya evam anya avashy

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of above 25mm and up to 40 mm DAR NO-15.23.2

Providing and layeing in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level:1:5:10 (1 cement :5 coasre sand ( Zone-III) :10 graded stone aggregate 40 mm nominal size dar-4.1.10

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved DAR NO-16.91.2

Brick work with common burnt clay (non madular) brick of class- 150 in superstructure above plinth level up to floor V level in all shape and sizes in cement mortar 1:4 ::(1 cement :4 coarse sand )( Dar 6.4.1)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix:1:3 ( 1 cement :3 fine sand ) 13.8.1

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick dar-11.26.1

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required::In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (10.25.2)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m² DAR NO-12.1.1

Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required(12.8)

Supply of woter stroage tank cover Double insulation effect .A-Aluminum foil effectively reflvety B-Rainforced bubble core prevent heat loss C-Aluminum foil enhance insulation effect.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.DSR 10.27.1

Providing and fixing stainless steel (grade-304 ) ralling made of hollow tube , channels , plates etc . Including welding , grinding , buffilg , polishing and making curvature (wherever requried ) and fitting the same with necessery stainless steels nuts and bolts complete i/c fixing the railling with necessery accessories & stainless steel dash fasteners , stainless steel bolts etc of requried size on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts , bolts fasteners etc ) dar-10.28