REPAIR/MAINT OF SUBMERSIBLE PUMP SET, MONO BLOCK PUMP SET, HORIZONTAL SUBMERSIBLE PUMP SET, WATER FOUNTAIN, DOL/STAR DELTA STARTER AND OTHER MACHINERIES OF WATER SUPPLY SYSTEM ALONG WITH CERTAIN CONNECTED WORKS UNDER GE E/M LUCKNOW

Amount

Dismantling of Oil immersed starter electrically & mechanically of capacity 7.5 HP to 30 HP of any make /size and transporting from Pump House to Contractor's work shop for carryout necessary repair and overhauling, including re-assembling complete all as specified and directed. Note:- (i) New spares/ parts shall be measured & paid separately for unserviceble parts under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Supply only set of fixed and moving Contact complete all as specified and directed.

Supply only of base Plate assembly complete all as specified and directed.

Supply only set of auxiliary switch I No (Normal open contact) + 1 NC (Normal closed contact), complete all as specified and directed.

Supply only magnet coil with auxiliary winding rated 415V, AC, 50 Hz complete all as specified and directed.

Supply only thermal overload relay type RB-1 63 range 25 to 40 Amp or 36 to 60 Amp complete all as specified and directed.

Supply only start & Stop Switch complete all as specified and directed.

Supply only thermal time delay, relay without transformer type RZ-12 having actuating time range 3 to 12 second complete all as specified and directed.

Supply only kit kat fuse suitable for 25 HP starter complete all as specified and directed.

Supply only terminal links RYB & Delta complete all as specified and directed.

Rewinding of unserviceable / burnt auto transformer with existing size of winding wire complete all as specified and directed.

Supply only reset push button assembly complete all as specified and directed.

Transportation of submersible pump or motor 20 HP to 35 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump and reassembling complete motors/pump sets & depositing the same after necessary repair to site complete all as specified and directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

M&L for cutting out the burnt existing winding of startor of submersible motor of any make and rewinding with the same size of , copper winding wire, etc as per existing complete all as specified and directed.

Straightening only of the slots of stator of submersible motor, complete all as specified and directed.

Supply only thrust of ball bearing block complete for submersible motor, complete all as specified and directed.

Renewal only of worn out gun metal bushes for submersible motor as per manufacturer's design, complete all as specified and directed.

Supply and fixing in repairs PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 6 sqmm size, 8 mtr long complete with suitable clips, complete all as specified and directed.

Supply only sand guard of submersible motor, complete all as specified and directed.

Supply only sleeves of end plates of submersible motor, complete all as specified and directed.

Supply only cable grommet (guard), complete all as specified and directed.

Supply only water seal, complete all as specified and directed.

Re-metaling of motor shaft, turning to bring it to original size and shape and polishing of shaft of submersible pump complete all as specified and directed.

Supply & fixing in repair coupling of submersible motor and pump with key, complete all as specified and directed.

S & F in repair of broken Pump shaft with new piece, making key slot, grinding to make coupling size, and balancing the rotor, complete all as specified and directed.

M&L in repair of pump shaft of submersible pump by carrying out, balancing of pump shaft and cutting of key slots, repairs to bowl assembly, rethreading of wornout studs holes and provding over size studs with nuts complete all as specified and directed.

Supply only bowl bushes complete all as specified and directed.

Supply only neck ring complete all as specified and directed.

Supply only steel distance pieces & key, complete all as specified and directed.

Supply only impellor gun metal as per existing, complete all as specified and directed.

Supply only cast iron, bowl, complete all as specified and directed.

Supply only CI, non return valve of required dia, complete all as specified and directed.

Supply only of Wedges of slots, complete all as specified and directed.

Jointing of 3 core submersible cable of any size by using puncture/ rubber compound roll & tape / Sealing compound etc, complete all as specified and directed.

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed. Note:- Painting shall be done by spray machine.

Transportation of submersible pump or motor 15 HP/7.5/5.0 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump & depositing the same after necessary repair, reassembling complete to site complete all as specified and directed. Note:- (i) Spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

M&L for cutting out the burnt existing winding of startor of submersible motor of any make and rewinding with the same size copper winding wire, etc as per existing complete all as specified and directed.

Straightening of the slots of stator in repair of submersible motor complete all as specified and directed.

Supply only thrust ball bearing block as per existing size complete for submersible motor complete all as specified and directed.

Renewal worn out gun metal bushes for submersible motor as per manufacturer's design and specification, complete all as specified and directed.

Supplty & fixed PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 4 sqmm size, 8 mtr long complete with suitable clips complete all as specified and directed.

Supply only sand guard of submersible motor, complete all as specified and directed.

Supply only sleeves of end plates of submersible motor, complete all as specified and directed.

Supply only cable grommet (guard), complete all as specified and directed.

Supply only water seal, complete all as specified and directed.

Supply only studs with nuts of required length & dia, complete all as specified and directed.

Re-metaling of pump shaft, turning to bring it to original size and shape and polishing of shaft of submersible motor complete all as specified and directed.

Supply only coupling of submersible & pump with key motor complete all as specified and directed.

M&L in repair of submersible pump by carrying out, balancing of pump shaft and cutting of key slots, repairs to bowl assembly, rethreading of wornout studs holes and provding over size studs with nuts complete all as specified and directed.

Supply only bowl bushes, complete all as specified and directed.

Supply only neck ring, complete all as specified and directed.

Supply only steel distance pieces & key, complete all as specified and directed.

Supply only impellor gun metal as per existing, complete all as specified and directed.

Supply only cast iron bowl assembly, complete all as specified and directed.

Supply only CI non return valve of required dia, complete all as specified and directed.

Supply only Head Extention (cast iron) complete all as specified and directed.

Jointing of 3 core submersible cable of any size by using puncture/ rubber compound roll & tape / Sealing compound complete all as specified and directed.

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed. Note:- Painting shall be done by spray machine.

Transportation of Centrifugal monoblock pump set/Horizontal submersible Pump- 10HP to 20HP, AC, 3 phase, 415/420 V from pump house at any location/Yard transporting to contractor's work shop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete to site complete all as specified and directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Cutting out the existing winding of the motor, opening of winding, re winding of motor with same size of winding wire as existing including varnishing, drying and making connection complete all as specified and directed.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer, complete all as specified and directed.

Supply only driven end bearing of pump shaft, complete all as specified and directed.

Supply only gun metal / stainless steel bush of pump shaft, complete all as specified and directed.

Remateling and repairing of pump shaft, complete all as specified and directed.

Supply only non driven end bearing of pump shaft, complete all as specified and directed.

Supply only of gland and packing, complete all as specified and directed.

Supply only CI impeller of similar make complete all as specified and directed.

Supply only connection pipe, complete all as specified and directed.

Supply only coupling with studs between motor & pump, complete all as specified and directed.

Supply only sleeve of motors as per existing size complete all as specified and directed.

Re-metaling of pump shaft, turning for bring it to Internal dia size of bearing in rear end cover complete all as specified and directed.

Supply only Neck ring, complete all as specified and directed.

Dismantling of Centrifugal pump Set/Horizontal submersible pump set from its existing position and re-fixing in the same location and necessary electric connection, nut & bolt etc, complete all as specified and directed.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed. Note- Painting shall be done by spray machine.

Transportation of monoblock pump sets/ Horizontal submersible pump set 1 HP to 7.5 HP, AC, Single/three phase, 220/440 V from pump house at any location/Yard in Cantt area contractor's workshop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete all as specified and directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete.

Cutting, opening of winding, re- winding of monoblock pump set/ Horizontal submersible pump set of any make and rewinding with same size of copper winding wire, varnishing, backing complete all as specified and directed.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer. Balancing and repairing of pump shaft, complete all as specified and directed.

Supply only water seal and packing complete, complete all as specified and directed.

Supply only driven end bearing of pump shaft, complete all as specified and directed.

Supply only non driven end bearing of pump shaft, complete all as specified and directed.

Supply only cooling fan, complete all as specified and directed.

Supply only cooling fan cover, complete all as specified and directed.

Supply only CI impeller of as make complete all as specified and directed.

Supply only connection plate, complete all as specified and directed.

Supply only capacitor of required capacity, complete all as specified and directed.

Removing of Monoblock pump Set from its existing position and re-fixing of repaired pump set including replacement of worn out nuts & bolts and supply and fixed nuts, bolts and electric connection complete all as specified and directed.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) complete all as specified and directed. Note:- Painting shall be done by spray machine.

Supply and fixed in repairs Single Phase Preventor Relay Minilex BSP-II, complete all as specified and directed.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 20 to 25 HP, 3 Phase, 415 V electric motor including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all as specified and directed.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 30 to 35 HP, 3 Phase, 415 V electric motor including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all specified and directed.

M&L Mild screw nut, bolts with washer 12 mm dia and 100 mm long ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed

Supply & fix in repairs electronic control timer type ET-100 of suitable capacity as required at site, complete all as specified and directed.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 16 sqmm 3 core complere all as specified and directed.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 10 sqmm 3 core complere all as specified and directed.

S&F tail pipece in replacement made out MS ERW pipe heavy duty 100 mm dia upto 1.0m in length suitable for submersible pump upto 30 HP including making arrangements for fixing of tie rod, cutting thread & welding flange all as sper site requirement complete all as specified and directed.

Disconnection of submersible pump set of any capacity/ size from existing water supply system electrically & mechanically and Taking out /Uplifting the U/S pump set from deep borewell with disconnected from lowering pipe line of any size with manual or suitable electric driven chain pully upto 240 ft depth and re-lowering after neccesary repair the pump set in same borewell complete all as specified and directed. Note:- (i) Repair of U/s pump set will be paid separately. (ii) All type of T/P required to complete the job will be arranged by contractor. (iii) Job will be done round -o-clock continued as per site requirement as directed by AGE. (iv) Items required for motor connection such as PVC insulation tape, valcanised rubber / puncture tube etc will be provided by the contarctor to complete the work and rate as deemed to be quoted in unit rate no extra payment will be made to the contractor.

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 100 bore flange lowering pipe cut type complete all as specified and directed

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 150 bore flange lowering pipe cut type complete all as specified and directed

S & F in repair submersible pump assy upto 12 stages not less than 07 stages incluiding bearing, bush ,shaft, bowls, thrust bearing, bronze impellers of pump etc comprising /suitable arrangement for directly coupled with motor of cap 15 HP cast iron body suitable for 300 mm dia borewell multi-stages ,discharge of 600-800 LPM at 91 Metre head and complete with suitable end connecting tail piece, NRV complete all as specified and directed.

S & F in repair submersible motor assy of capacity 15 HP with Stator incluiding insulated copper winding, rotor, bearing, bush, thrust plate terminal plate and casing of motor comprising with arrangement of directly coupled with pump cast iron body electric driven 415V, TP along with connecting tail piece, NRV and submersible cable minimum 7.5 RM complete all as specified and directed.

S & F in repair submersible pump assy of 12 stages incluiding bearing, bush ,shaft, bowls, thrust bearing, bronze impellers of pump etc comprising /suitable arrangement for directly coupled with motor of cap 25 HP cast iron body suitable for 300 mm dia borewell multi-stages ,discharge of 600-800 LPM at 91 Metre head and complete with suitable end connecting tail piece ,NRV complete all as specified and directed.

S & F in repair submersible motor assy of cap.25 HP with Stator incluiding insulated copper winding, rotor, bearing, bush, thrust plate terminal plate and casing of motor comprising with arrangement of directly coupled with pump cast iron body electric driven 415V, TP along with connecting tail piece, NRV and submersible cable minimum 7.5 RM complete all as specified and directed.

Attending the complaint of Oil immersed star delta starter with auto transformer upto 50 HP capacity And AMF Panel round the clock including Sunday & Holiday at any location in Lucknow Cantt area with in specified time not more than two hours complete all as specified and directed. (Note :- (i) Work requisition as per Annx I duly signed by all concerned kept on record and shall be submitted to GE alongwith RAR. (ii) Spare parts upto cost of Rs. 100.00 shall be included in the unit rate quoted by the bidder. (iii) Any other spare parts shall be measured and paid separately under appropriate items. (iv) Complaint shall be recitifed within 72 Hours from the date of complaint, failing which recovery shall be charge @ Rs. 50.00 per complaint per day.)

M&L for replacement of MS panel of steel water tank installed at AMC Trg area made out of MS sheet 4mm thick connected with nut, bolts & washers of MS panel end to end inside and outside surface of panel of size 1.2m x 1.2m (variable size) panel size, cutting & grinding, welding with and including two coat of synthetic enamel paint over a coat of red oxide primer and preparation of new steel surface with putty, complete all as specified and directed.

commercial construction

Magneoflux