Repair to Rolling shutter, Stone masonry, PCC flooring and Misc works in certain units in Zone-II under GE (A) Jaisalmer

Amount

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed by Engineer-in-charge.

Taking down chowkat (without taking of shutter from the frame) not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 and white wash and cement base paint complete all as specified and directed by Engineer-in-charge.

Ditto- all as per item No 02 above but exc 1.5 sqm and n exc 4 sqm each

Running welding in repair thickness of metal to be welded n.exc 6mm including cleaning and preparing the surfaces to be together, holding the members in the true position while welding and bevelling of edges complete all as specified and directed by Engineer-in-charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes, S&F in opening as per specification & drawing given in SSR 2010.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing ccomplete all as specified and directed by Engineer-in-charge.

S&F Pressed steel frame size 125 x 60mm for doors with one or more rebates including necessary fixing lugs,hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-charge.

S&F Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats second class hard wood 35mm thick for door shutter complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-charge.

S&F aluminium anodized tower bolt 150mm size complete all as specified and directed by Engineer-in-charge.

S&F Butt hinges Aluminum 75 mm type C21 complete all as specified and directed by Engineer-in-charge.

S&F Butt hinges MS 100 mm cold rolled complete all as specified and directed by Engineer-in-charge.

S&F aluminium handle 125 mm cast type anodized complete all as specified and directed by Engineer-in-charge.

S&F mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and directed by Engineer-in-charge.

M&L preparation of new wooden surfaces exc 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L preparation of new decorded steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-charge.

S& F Galvanized mild steel wire cloth, .56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples fixed complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass of any thickness size,quality or description from metal frames and S&F 3mm thick frosted glass with glazing clips and oil putty complete all as specified and directed by Engineer-in-charge.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge.

M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring/hard standing complete all as specified and directed by Engineer-in-charge.

M&L for 25 thick sand cushing for laying of precast concrete interlocking tiles including watering and consolidation complete all as specified and directed by Engineer-in-charge.

M&L for 60mm thk, M 35 grade machine pressed precast concrete interlocking paver block rubber mould using grey cement and no pigment of any shape and size conforming to IS 15658 - 2006 complete all as specified and directed by Engineer-in-charge.

S&F chequered cement concrete tiles 20cm X 20 cm X 25mm thk with grey cement and pigments, set jointed in neat cement slurry as in floors/path etc over and including 15mm thk screed bed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for 75 mm thick PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in flooring complete all as specified and directed by Engineer-in-charge.

M& L for 50mm thick PCC (1:3:6) type C1 using 20mm graded stone aggregate laid in alternative as in plinth protection including finished the surface even and fair without using extra cement and filling the joints with mastic filling ie one part of bitumen 85/25 & 3 parts of sand by weight complete all as specified & directed by Engineer-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. loaded bedded and pointed in any mortar complete all as specified & directed by Engineer-in-Charge.

M&L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types complete all as specified & directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid over screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes screeding and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laying floor finishes all as specified and directed.

M&L sand stone slabs 5cm thick in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified & directed by Engineer-in-Charge.

Taking down cement plaster on brick/stone/concrete surface including wall tiling or terrazo finish and hacking out joints hacking for key scrubbing down with water etc complete all as specified & directed by Engineer-in-Charge.

M&L rendering 15mm thick on surface of stone masonry or surface other than fair face of brickwork in CM 1:6 all and it is to be finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:4 & finished the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for rendering 5 mm thick on fair faces faces of brick work or concrete surfaces of ceilings in cement plaster 1:3 & finished the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L preparation of new plastered surfaces and applying two coat of oil bound distember over a coat of white wash on walls complete all as specified & directed by Engineer-in-Charge.

M&L for two coats of cement base paint over a coat of primer on walls complete all as specified & directed by Engineer-in-Charge.

M&L preparation of new plastered surfaces and applying three coat of white wash on ceiling complete all as specified & directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) complete all as specified & directed by Engineer-in-Charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floorS&Finishing the surface even & smooth without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, joint free non skid tiles and including scread bed or bedding layer 15mm thick in CM 1:6 complete all as specified & directed by Engineer-in-Charge.

M&L for vetrified ceramic coloured tiles 9 to 10 mm thick area of each tile not exc 0.38sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as directed (size 600mm to 600mm) complete all as specified & directed by Engineer-in-Charge.

M&L non skid ceramic coloured tiles 7-8mm thick(square/rectangular) area of each tile exceeding .11Sqm but n.exc .18Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engineer-in-Charge.

M&L glazed ceramic coloured tiles (450x300mm)x 7mm thick joint free in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 etc complete all as specified & directed by Engineer-in-Charge.

Dismantling boarding of any description fixed in any position fixed with screws complete all as specified & directed by Engineer-in-Charge.

S&F 18/19mm thick pre-laminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination alround 6mm th teak fillets fixed in kitchen CB or pelmet complete all as specified & directed by Engineer-in-Charge.

M&L for 2nd class hard wood fillets square, rectangular as in lippings fixed with nails of area exc 3Sqcm but n.exc 6sqcm complete all as specified & directed.

S&F 40mm width of flaps (when open) continuous (piano) hinges, mild steel bright finish or electroganised fiwed to wooden or angke iron frame complete all as specified & directed by Engineer-in-Charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-Charge.

S&F 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws /fixed in repairs complete all as specified & directed by Engineer-in-Charge.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-Charge.

S&F in repair 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed by Engineer-in-Charge.

S&F in repairs Floor door stopper of aluminium alloy body 140mm long complete all as specified & directed by Engineer-in-Charge.

S&F in repair aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified .

S&F in repair aluminum handles cast type, anodised, 150mm size complete all as specified & directed by Engineer-in-Charge.

S&F in repairs Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified & directed.

S&F in repair 4 lever mild steel mortice lock, vertical type, size 100 mm complete all as specified & directed by Engineer-in-Charge.

S&F in repair aluminium die cast body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed approved by Engr-in-Charge

S&F in repair anodised aluminium alloy Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.(Curtain rods) complete all as specified & directed by Engineer-in-Charge.

S&F in repair butt hinges Aluminum 100 mm type C21 complete all as specified and as directed

S&F in repair Steel rolling shutter (thickness of lath 1.25mm thick) without ball bearing as specified including top hood cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated and including taking down of any thickness etc, complete push pull or manual type complete all as specified & directed by Engineer-in-Charge.

S&F in repair Steel rolling shutter (thickness of lath 1.25mm thick) without ball bearing as specified including top hood cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, and including taking down of any thickness etc, complete gear operated type with bevel gear box and crank handle complete all as specified & directed by Engineer-in-Charge.

Taking down Aluminium anodised door, window and ventilator complete w/o taking off the from frame complete all as specified & directed by Engineer-in-Charge.

S&F Aluminium anodised frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc complete all as specified & directed by Engineer-in-Charge.

S&F aluminium anodised window and ventilator shutters,hung type without sash bar aluminium section wt 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised snap beading, screws etc, complete all as specified.

S&F Anodised aluminium door shutters,aluminium section wt 0.55 kg/m including necessary jointing cleats ,glazing clips rubber neoprane packing ,handles 2 Nos in each door hinges, anodised aluminium snap beading screws etc complete all as specified.

Hacking out old broken glass (any thickness, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-Charge.

S&F 5.5mm thick sheet glass, ordinary quality and glazing in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

Dismantling of Ceiling Board of any description and any thickness including Cover Fillets, Cornices, etc complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling complete all as specified & directed by Engineer-in-Charge.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified & directed by Engineer-in-Charge.

M&L for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified & directed by Engineer-in-Charge.

M&L for 12mm thick seamless calcium silicate ceiling made out of 1800 x 1200x 12 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately complete all as specified & directed by Engineer-in-Charge.

BHAGWATI CONSTRUCTION

JASOL MAA ENTERPRISES

M/s Shri Inder Construction Company

S AND S Constructions

Leelashah Enterprises

GEMRARAMCONTRACTOR

S R ENTERPRISES