CONSTRUCTION OF GUARD ROOM ,VEHICLE PARKING SHED,SPECIAL REPAIR TO PERS LINE OF MH AND CERTAIN MINOR WORKS UNDER GE SATWARI

Amount

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) exc 1.5 sqm & n. exe 4 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) n exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down shutters of any description exc 1.00 Sqm but not exc 2 sqm each and removing from the site all as specified & directed.

Taking down shutters of any description and refixing it in the same opening exc 1.00 Sqm but not exc 2 sqm all as specified & directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises.

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster / demolition of cement concrete any thickness and removal of debris off the premises complete all as specified and as directed by Engineer-In-Charge.

Taking down cement plaster of any description on brick wall including racking out joints, hacking for key, scrubbing down with water and removing all the demolished material outside cantt area complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing all the demolished material outside Cantt area complete all as specified.

Demolition of cement concrete (unreinforced) ground floor to 4th floor and pavings n exc 15 cm thickness (below or above ground level ) and removing unserviceable material outside cantt area complete all as specified.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,cables,pipe line,pole etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out, in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

Surface dressing n exc 15cm deep and getting out in any type of soil complete all as specified.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil, all as specified.

Spreading and levelling in layers n exc. 25 cm thick,watering and well ramming in layers as in floors with earth obtained from excavation complete all as specified and directed by Engineer-In-Charge.

Returning filling in including spreading, leveling watering and well ramming in layers n.exe 25cm thick in any type of soil complete all as specified.

Removal of surplus soil to a distance n.exc 50mtr and depositing at a level n.exc 1.5m above starting point all as directed by Engr-in-Charge.

Material and labour for concrete bed in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) to drain pipe 150mm bore including packing under & haunching against the sides after they are laid and tested complete all as specfied.

Material and labour for salt glazed stone ware 150 mm bore internal diameter drain pipe grade 'A' laid in trenches and jointed in cement mortar 1:2complete all as specified and directed by Engr-in-Charge.

Plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate), as in subbase, mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate), as in subbase, mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for ATT treating in contact with foundation at the rate of 7.5 ltrs of emulsion per sqm of vertical surface area

Material and labour for ATT treating under the soil surfaces of plinth protecion at the rate of 5 ltrs of emulsion per sqm of surface area

Material and labour for ATT treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area

Material and labour for ATT treating the top surfaces of filled earth at the rate of 5 ltrs of emulsion per sqm of surface area

Material and labour RCC (Design Mix) M-25 as in columns, pillars, piers, posts and struts etc complete all as specified and directed

Material and labour RCC (Design Mix) M-25 as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed

Material and labour RCC (Design Mix) M-25 as in foundation beams, plinth beams, basement slabs, bases for columns etc under reamed piles and mass concrete complete all as specified.

Material and labour for RCC M-25 design mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns complete all as directed.

Material and labour RCC (Design Mix) M-25 as in in slabs supported on walls beams and columns in floors, roofs, landings, balcony, canopies, deck slabs and in slaves and like..

Material and labour RCC (Design Mix) M-25 as in chajjas fins, facias,etc completed all as specified as directed

Material and labour Pre-cast PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in manhole cover slab set in CM 1:4 complete all as specified and directed

Supplying, laying, jointing & testing galvanised iron pipe 20 mm bore medium grade with screwed joint together with all fitting such as bends, elbows,tees,short pieces and union etc fixed to walls or laid in floors,trenches including all fittings complete all as specified and directed.

Supplying, laying, jointing & testing galvanised iron pipe 15 mm bore medium grade with screwed joint together with all fitting such as bends, elbows,tees,short pieces and union etc fixed to walls or laid in floors including all fittings complete all as specified and directed.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified.

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 over 5 mm thick in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified.

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified.

Material and labour for repairing of concrete surfaces such as chajjas,upward facia,downward facias,ceiling and similar items with plain cement concret 1:2:4 type B-0 or rendering 10mm thick in CM 1:3 includind dubbing coat without using extra cement finished even and fair including necessory formwork and scaffolding complete all as specified and directed.

Plain cement concrete M-15(1:2:4), type B-0 (using 12.5mm graded crushed stone aggregate), nominal mix, 25 mm thick, as in floors, finished even and fair complete all as specified and as directed by Engineer-In-Charge.

Material and labour for hardcore of broken stone of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick watered and well rammed to a true surface, complete all as specified and directed

Material and labour for machine pressed precast concrete interlocking paver block of any shape and size conforming to IS 15658-2006 of 60mm thickness M-40 Grade with white cement and pigment to match laid over and including 25 mm thick dry sand cushoning etc (colour and pattern as per sample kept in GE office as approved by GE) laid over 75mm thick PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate over rammed earth complete all as specified and directed by Engr-in-Charge.

Material and labour for precast factory made designer tiles (Rectified interlocking tiles) glazed top made in white cement and pigment base of thickness not less than 20mm in different colour and pattern (compressive strength not less than 250 kg/sqcm) set and jointed in neat cement slurry (colour and pattern as per sample kept in GE office as approved by GE) including 15 mm thick screed bed in CM 1:6 all as specified and directed by Engr-in-Charge

Use and waste formwork to sides of pillars, posts, struts, pier, column square, rectangular or polygonal rough finished surface of concrete

Use and waste formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves etc with fair finished surface of concrete.

Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete rail­ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon­tal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste formwork to chullah hoods, cha­jjas, troughs and similar items including edges complete for flat and rough finished surfaces all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified.

TMT bars 10 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

Description all as per item No 49 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and builders.

TMT bars 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

Rendering 15 mm thick on concrete surface over roofs in cement mortar 1:4 finished even and smooth without using extra cement on walls/floors including mixing of water proofing compound complete all as specified and as directed by Engineer-In-Charge. (WPC shall be measured and paid for separately)

Applying roof treatment as below:-- (i) Applying 1st coat of bitumen primer membrane 0.4ltr/sqm by the same membrane manufacturer of density at 25 degree C’ 0.87-0.89Kg/Litre and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely (ii) Applying 2nd course of a coat of blown type bitumen of grade 85/25 heated to a temperature of 180 degree centigrade and applying @ 1.2 kg/sqm completely (iii) Applying 3rd course of Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3.6 Kg/Sqm with 160 grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 overlap in length using butane torch with 10cm over laps which shall be thermo fused by flame (iv) Applying course of two coats of aluminium paint over the APP membrane all as specified. All joints and change in direction shall be covered with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement and curved before laying membrane MAKE-IWL/Pidilite Note : Ponding shall be done over RCC slab by filling water which shall be kept for 48 hours.In case a slightest indication of seepage / leakage is noticed the same shall be rectified by grouting the affected portion at no extra cost.Thereafter ponding test shall be repeated till there is no indication of seepage /leakage before application of roof treatment.A proper record of ponding test of RCC slabs shall be maintained by Engr in Charge.The arrangement of ponding test shall be made by the contractor and shall be included in the quoted rates..

Complete removal of existing treatment including washing, rubbing down with sand paper and stopping of distempered and painted surfaces including preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion over and including one coat of primer over two coats of Birla wall care putty 2 to 3 mm thick on plastered surfaces, preparatory to distempering, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation of new surface over 10cm width or girth complete all as directed by Engr-in-Charge

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer including necessary putty filling with knife of same colour where required to achieve smooth and even surface complete all as specified ooth complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement paint over and including one coat of primer, complete all as specified and as directed by Engineer-In-Charge.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of cement paint, complete all as specified and as directed by Engineer-In-Charge.

Preparation of old plastered surfaces including prepation of old surfaces ,peeling off and applying two coats of white wash on ceilings complete all as specified and directed by Engineer-in-charge.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing, complete all as specified and as directed by Engineer-In-Charge.

Preparation of newly plastered surfaces of wall and applying two coats of Oil bound distemper over a coat of alkali resistant priming paint with 2mm thick birla white wall putty as under coat complete all as specified.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing, complete all as specified and as directed by Engineer-In-Charge.

Preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered surfaces of wall and applying two coat of cement base paint including a base coat of primer surface complete all as specified and as directed by Engineer-In-Charge.

Preparation of old plastered surfaces of wall and applying two coat of cement base paint complete all as specified and as directed by Engineer-In-Charge.

Material and labour for Vitreous China squatting pan 'Orissa' pattern size 580x440mm white with integral foot rest with 'P' or 'S' trap (excluding flushing cistern and flush pipe) and provision of lime concrete and making good floor, all as specified.

Supply and fixing Vitreous china bowl urinal flat back, size 465 x 355 x 265 mm, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete, fixed in repairs all as specified and as directed.

Material and labour for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

Plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in surface channels and drains including necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms,moulds,mitred/stopped ends etc complete all as specified and as directed by Engineer-In-Charge.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe,complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap, including soft closing seat cover , closed pattern with flat bottom, complete all as directed.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets,PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Vitreous China wash basin, white, flat back, size 550x410X190 mm including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of chromium plated brass, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Bib taps long body,cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe complete all as specified and as directed by Engineer-In-Charge.

Stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe,Supply and fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Angle valves cast copper alloy, chromium plated fancy type half turn screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing fancy type soap dish holder chromium plated complete all as specified.

Supply and fixing ABS Brass chromium plated shower rose with swivel joints 125mm size for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge

Supply and fixing tubular towel rail, 20mm dia, D type, 60cm long between flanges, chromium plated fixed to walls with chromium plated brass screws complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Supply and fixing in repair 25mm outer dia curtain rod brackets/end pieces fancy type fixed to wall with screws and PVC rawl plug complete all as specified and directed (ISI marked)

Material and labour for brick work in cement mortar 1:6 using sub-class B bricks straight or curved on plan exc 6 mtr mean radius all as specified.

Material and labour of Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6mtr mean radius built in CM 1:4 complete all as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan any radius half brick thick wall built in CM (1:4) complete all as directed.

Material and labour PCC 1:4:8, 75mm thick type D-2 using 40mm graded crused stone aggregate as in subbase complete all as directed.

Supply and fixing stainless steel gratings of outer frame dia 150 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement.

Supply and fixing GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed by Engr-in- Chage.

Material and labour for cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) in cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like incl weathering slightly rounded our chamfered angles and threading complete all as specified and directed.

Machine cut kota stone slab, (minimum size shall be 550x550mm), flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, laid over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Machine cut kota stone 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, , set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles over and including 10mm thick rendering in cement mortar 1:4, as in verticle surfaces complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 75 mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

Cutting chases, pinning in. making good to facings in brick walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing pressed steel frames( factory made) made of cold rolled mild steel sheets of 1.25mm thickness as indicated in IS for door with one or more rebates incl lugs, hold fast, lock strike plate etc complete of size 105 x 60mm including back filling of chowkats in PCC 1:3:6 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spd and as directed.

Supply and fixing in repairs Pressed steel frame (factory made) of size 125x60mm for doors with double rebated including mild steel hinges medium weight 100 mm long and 25x3 mm flat iron in holdfast, tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc., complete as specified including back filling of chowkats in PCC 1:3:6 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spd and as directed.

Supply and fixing pressed steel cup board frame made to size from MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:3:6 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Material and labour 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fixed to chowkats complete all as directed.

Material & labour flush shutters,factory made both side commercial face door shutter 30 mm thick solid core construction, with block board core and plywood face panels commercial type on both sides complete all as specified and as directed by Engr-in-Charge.Make Archidply,Centuryply,Greenply

Material and labour for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete and similar work conforming to Fe 410-W(Gde-E- 250) quality-A complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing 35mm thick 2nd class Hardwood factory made rail and style plain framed, panelled shutter (any number of panels) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as directed.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixingin repair Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement Supply and fixing in frame at site as per specification.

Supply and fixing Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including locking arrangements complete all as directed by the Engineer-in-Charge.

Supply and fixing Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including locking arrangements complete all as directed by the Engineer-in-Charge.

Supply and fixing steel ventilators with top hung shutters including projecting type hinges with steel handles, 2 Nos steel tower bolts on each shutter, 100mm long peg stay complete with glazing bars, dovetailed or welded including locking arrangements complete all as directed by the Engineer-in-Charge.

Supply and fixing Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of size 250mm long.(ISI marked)

Supply and fixing extruded aluminium alloy handles, fabricated type,anodised 150 mm size all as specified and directed (ISI marked)

Supply and fixing hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws 100 mm size all as specified and directed (ISI marked)

Supply and fixing butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

Supply and fixing stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified.

Supply and fixing Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supply and fixing Aluminium anodised, barrel tower bolts size 100 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supply and fixing Aluminium anodised, barrel tower bolts size 50 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supply and fixing aluminium anodized door handle size 150mm size of extruded section complete all as specified and directed.

Supply and fixing mild steel helical/ordinary rat tail rod pattern door spring 375 mm including roller and roller plate complete fixed with welding all as specified.

Supply and fixing in repair continuous (piano) hinges, heavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( ISI Marked)

Supply and fixing in repair 18/19 mm thick MDF board as in shutters/shelves etc exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed to frame work with leaping (15 mm thick three side and 20mm thick leaping hinge side) around the shutter and fix with screws to etc complete all as specified and directed.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(65x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung including pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specified and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs.

Supply and fixing Aluminium alloy, anodised, sliding door bolt size 300 mm (length of bolt) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete al as specified. (ISI Marked)

Supply and fixing Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured).

Material and labour Non - skid Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the surface over and including 15mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour glazed ceramic tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over and including 10 mm thick rendering in CM 1:4 all as specified. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Supply and fixing 75 mm bore PVC (SWR)Type B pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches or fixed with wall complete all as directed.Make:Finolex/Kisan/Supreme

Supply and fixing 110 mm bore PVC (SWR)Type B pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches or fixed with wall complete all as directed.MakeFinolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) bends provided with access door radius 75mm bore Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) bends provided with access door any radius for 110 mm bore Make :- Finolex/Kisan/Supreme

PVC (SWR) branch piece,single (double T) equal or unequal of 100 mm bore, any radius, complete all as specified and as directed by Engineer-In-Charge.

PVC (SWR) branch piece,double (double T) equal or unequal of 75 mm bore, any radius, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair PVC (SWR) reducers( Grade " B " ) 110 mm bore complete all as specified and as directed by Engineer-In-Charge. Make :- Finolex/Kisan/Supreme

Supply and fixing PVC Waste pipe 32mm bore for required length complete with waste coupling .Make: Prayag Cat No 3272,Hindware,Somany,CERA,Jaquar

Material and labour for urinal spreader of brass, chromium plated fixing with 15mm dia pipe.

Supply and fixing in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

Supply and fixing PVC (SWR) floor trap 75 mm bore type B , plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing Salt-glazed stoneware gully traps, square or round mouthed, type 'P' Size 150 x100 mm complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing 75 mm bore UPVC (SWR) Type B vent cowl complete all as directed.

Supply and fixing 110 mm bore PVC (SWR) Type B vent cowl complete all as directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm- 2 1 0 gms screwed both ends for iron pipe or for unions and fixed for 20 mm bore pipe in repairs, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) triple layered,white,hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe and 20 mm dia galvanised iron pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings , including making connections complete all as specified.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) triple layered,white,hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe and 20 mm dia galvanised iron pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings , including making connections complete all as specified.

Material & labour for framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 all as directed by the Engineer-in-Charge.

Supply and fixing 3 mm thick sheet glass ordinary quality glazing with steel pins,oil putty to steel windows and, beads nails etc to wooden surfaces as in square exc 0.50 sqm in each pane, (up to 4th storey with necessary scaffolding) all as specified.

Supply only Water proofing compound liquid.

Soakage well, 3.0 mtr dia and 3.00 mtr depth below inlet pipe (depth of inlet pipe 45cm below normal ground) including excavation and earth work in any type of soil, cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate in foundation, brick work in CM 1:4, RCC 1:2:4 Cover slab, manhole cover with angle iron frame, appropriate and suitable size brick bat filling, SWG junction 150mm bore CI vent pipe and Cowl etc. complete all as specified and as shown on drawings. (Soak well shall be constructed as per CE Pathankot Zone TD No CEPZ/C-TD/013/13 Sheet 1 to 5).

Material and labour for tube light grade galvanized with all fitting and fixed complete to wall and ceiling or laid in floors ,under road,path or along poles of size 40 mm dia complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Gun-metal, globe or gate valves, 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified. ( ISI Marked)

Material and labour for point wiring one light/fan point controlled by one, one way switch 6 Amp complete with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , terminated into modular galvanised suitable size sunken boxes incl white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed.Make of wire: Havells/Polycab.

Description all as per srl item No 147 but one 3 pin socket outlet 6 amp independent board.

Description all as per srl item No 147 but one 3 pin socket outlet 6 amp on same board.

Description all as per srl item No 147 but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for piont wiring and 2.5 sqmm as in continuous earth wire. complete all as specified and directed.

Supply and fixing sub main wiring with single core cable 2x 6 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x6 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.Make of wire: Havells/Polycab.

Supply and fixing LED tubelight fitting 18-20 W LED, 230V, Box type complete in all respect . Cat part No DMLN1LT8-16 of Crompton or equivalent in Havells, Wipro alongwith LED tubeRod with heat dissipation capability suitable for G-13 base tube lights base fluorescent T8/T12 luminaries, 20 watt LED wattage with colour temp of 5700 K 1800 lumens and with surge arrestor complete in all respect. Cat Part No LTT8-20 of Crompton or equivalent in Havells, Wipro. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fixing E-lite LED tubelight fitting 9 watt, 230V complete in all respect alongwith LED tubeRod complete in all respect including its connection with 2 core flexible copper conductor cable.. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fixing of lamp holder, PVC /Polycarbonate type with back plate for batten fitting with LED bulb 7 Watt.

Supply and fixing LED lamp suitable for B22 holder of capacity 7 watt Make : C&S Cat no. LTHPLEDLAMP7W/B22 or equivalent in Havells, Philips, Wipro.

Supply and fixing Distribution Board (SPN) double door 08 Way and should be IP 43 protected with Copper Bus bar, Earth Bar ,neutral Bar Door Earthing .Makes: IndoAsian Optipro Cat Part No 811807 or or equivalent in Havells/ Legrand

Supply and fixing modular switch Polycarbonate material ISI marked one way, 6 Amps, 240 V Make: Cat Ref 800100 Elvira Indoasian or equivalent in Havells, Legrand.

Supply and fixing modular socket outlet 6 Amps 3 pin Universal socket complete all as specified and as directed. Make: Cat Ref 800120 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing modular switch Polycarbonate material ISI marked one way, 16 Amps, 240 V Make: Cat Ref 800103 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing modular socket outlet 2 in 1, 6 / 16 Amps 3 pin socket complete all as specified and as directed having pencil free operation & child safety shutter . Make: Cat Ref 800122 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fix modular fan regulator step type (electronic ) 2 Module for 1200/1400mm sweep AC ceiling fan.Make: Cat Ref 800142 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fixing Distribution Board (SPN) double door 04 Way and should be IP 43 protected with Copper Bus bar, Earth Bar ,neutral Bar Door Earthing .Makes: IndoAsian Optipro Cat Part No 811805 or or equivalent in Havells/ Legrand

Supply and fixing MCB single pole neutral complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.Make:- IndoAsian Optipro Cat Part No 811151 or equivalent in Havells/ Legrand

Supply and fixing MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, ISI Marked complete all as specified and directed. Make:- IndoAsian Optipro or equivalent in Havells/ Legrand

Supply and fixing service connection with PVC insulated and PVC sheathed flat twin core cable 1100V grade heavy duty electric cable served all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire and loop insulators and as directed of size 16 sqmm cross sectional area stranded aluminium conductor complete all as specifed

Supply and fixing sub main wiring with single core cable 2x 4 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x4 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chasing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing AC single phase 240 Volt 50Hz ceiling fan of size 1200mm sweep complete in white colour 5 star rating with canopy with all accessories incl nuts, bolts, clamps etc., complete all as specified and directed. Make : Havells cat part No ES-50 premium 5 star ISI marked, Crompton cat part No : Entrust 50 or equivalent in Bajaj Excel star

Material and labour for cutting of existing wall of any thickness for fixing of Exhaust fan and making good the existing surface including matching with existing surface by rendering in cement mortar 1:4 and distempering all as specified and as directed by EIC.

Supply and fixing exhaust fan 380 mm sweep, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 900 rpm complete with louvers for wall mounting including grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. Make : Havells Cat part No Turbojet SP or equivalent in Crompton./Bajaj Note : Each exhaust fan shall be marked with the MES No in black/white paint clearly visible to naked eye when fitted in position.

Supply and fixing AC single phase 240 Volt 50Hz PVC exhaust fan 300 mm sweep complete with louvers for wall mounting including grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. Make : Havells Cat part No Ventil Air - DS or equivalent in Crompton/Bajaj. Note : Each exhaust fan shall be marked with the MES No in black/white paint clearly visible to naked eye when fitted in position.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 16 Sqmm X 2 core complete all as specified and directed by Engineer-In-Charge..

Supply and spreading dry river sand in trenches for cushioning of cable 8 cm thick layer before laying the cable and 15cm thick layer after laying the cable.

Supplying and laying dry bricks in trenches over under ground electric cable for mechanical protection with width equal to length of bricks with well-burnt sub class ‘B’ old size bricks laid flat complete.

Supply and fixing LED 1X30 watt LED IP66 New generation energy saving & environment friendly long life versatile pressure die-cast aluminium with lens and touchened glasstype roadway luminaire with high power LEDs as light source including electronic driver 30W LED 6000K working voltage 220-240V and as directed by Engr-in-Charge. Make : CAT PART NO LSTS-30-CDL of Crompton or equivalent IN C&S / Phillips / Havells / Jaquar fittings all as specified and as directed by EIC.

Supply and fixing LED roadway light luminaire aesthetically designed comprising of die cast aluminium housing including, poly carbonate cover with in-built electronic control gear with short circuit, over voltage and surge protection suitable for and including 45W LED with lenses, complete, all as specified and directed by Engr-In-Charge. Make:- Crompton Cat No LSTP-45-CDL or equivalent IN C&S / Phillips / Havells / Jaquar fittings all as specified and as directed by EIC.

Supply and fixing light bracket made out of GI pipe 1.5 Mtr long, 40 mm dia medium grade bent to shape as directed including two no clamps made out of 50 mm x 6 mm flat for fixing bracket suitable for PCC poles including nuts and bolts, washers and other connected items of required size including painting with one coat of aluminium paint over a coat of red oxide/primer all as specified and as directed.

Material and labour for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick buried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinforcement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

M/S K D Construction Co

M/S Shesh Paul Gupta

M/S PARAMJEET SINGH

Modh Hafiz Khan